1、REVISIONS LTR DESCRIPTION DATE APPROVED A Modify corona voltages for both cables. 12 July 2007 Lee Surowiec B Interface clarifications. Specify gold plating in accordance with MIL-DTL-45204. Add additional keying configurations. Editorial changes throughout. 1 April 2010 1 April 2010 Prepared in acc
2、ordance with ASME Y14.100 Source Control Drawing REV PAGE REV STATUS OF PAGES REV B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 5 June 2007 CHECKED BY TITLE CONNECTOR, ELECTRICAL, PLUG, RADIO FR
3、EQUENCY, SERIES ZMA, SOCKET CONTACT, FOR .141 AND .086, SEMIRIGID CABLE Mary McWilliams APPROVED BY Lee Surowiec SIZE CAGE CODE DWG. NO. 05005 A 037Z3 REV B PAGE 1 OF 9 AMSC N/A 5935-E833-002 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU
4、PPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 2 Dimension letter Dimensions Cable accommodation Minimum (mm) Maximum (mm) A .089 (2.26) .091 (2.31) M17/133-RG405 1/ .145 (3.68) .147 (3.73) M17/130-RG402 1/ B .650 (16.51) Reference C .312 (7.92) hex D .
5、050 (1.27) .056 (1.42) - 1/ All dash numbers for this specification sheet shall also apply. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. See figure 2 for all keying options.
6、 FIGURE 1. General configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 3 NOTE: Angular tolerance is 0 +1 FIGURE 2. Keying options, seri
7、es ZMA socket contact. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 4 Dimension letter Dimensions Dimension letter Dimensions Minimum (mm) Maxi
8、mum (mm) Minimum (mm) Maximum (mm) A .362 (9.19) .368 (9.35) H .173 (4.39) .177 (4.50) B .294 (7.47) .299 (7.59) J (see note 3) - .130 (3.30) C .182 (4.62) .184 (4.67) K (see note 3) - .130 (3.30) D .117 (2.97) .122 (3.10) L .215 (5.46) .221 (5.61) E .086 (2.18) .090 (2.29) M .325 (8.25) - F .050 (1
9、.27) .056 (1.42) P .105 (2.67) - NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. These are performance based dimensions. FIGURE 3. Interface dimensions, series ZMA socket contact. Provided by IHSNot for ResaleNo reproduction or networking permitted withou
10、t license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 5 MATERIALS: Connector body: Stainless steel in accordance with SAE-AMS5640. UNS S30300 (type I) condition A. Connector bodies shall be plated to a minimum gold thickness of
11、 50 micro inches (1.27 m) in accordance with MIL-DTL-45204, type II, grade C, class 1 (or equivalent as permitted by the qualification and preparing activities), over 50 micro inches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, appendix A, type 2.at least in the area of solder attach
12、ment. Contacts: Beryllium copper in accordance with ASTM B194, ASTM B196/B196M or ASTM B197/B197M. The socket contact shall be plated to a minimum gold thickness of 50 micro inches (1.27 m) in accordance with MIL-DTL-45204, type II, grade C, class 1 (or equivalent as permitted by the qualification a
13、nd preparing activities), over 50 micro inches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, appendix A, type 2, including the ID, measured at a depth of .040 inch (1.02 mm) minimum. The plating on non-significant surfaces in the ID shall be of sufficient thickness to ensure plating c
14、ontinuity and uniform utility and protection. This plating may consist of an underplate only. A silver underplate shall not be permitted. Insulator: PTFE in accordance with ASTM D4894 or ASTM D4895, or FEP in accordance with ASTM D2116. ENGINEERING DATA: (Metric equivalents are in parentheses and gi
15、ven for general information only) Nominal impedance: 50 ohms. Frequency range: DC to 12.4 GHz. Voltage rating: 1/ Applies to all dash numbers in the referenced specification sheet. Temperature rating: -65C to +165C. REQUIREMENTS: Requirements of drawing 84148 are applicable. Dimensions and configura
16、tion: See figures 1, 2 and 3. Force to engage and disengage: Longitudinal force: 48 ounces, maximum. Torque: Not applicable. Cable 1/ V rms, maximum (at sea level) V rms, maximum (at 70,000 feet) M17/133-RG405 335 85 M17/130-RG402 500 125 Provided by IHSNot for ResaleNo reproduction or networking pe
17、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 6 Mating characteristics: See figure 3 for dimensions. Test pins finish, 16 microinches (0.406 m). Center contact (socket); Oversize test pin: .0375 +.0001 inc
18、h (0.952 mm +.002 mm). Test pin finish: 16 microinches (0.406 m). Insertion depth: .030/.040 inch (0.76 mm/1.14 mm). Number of insertions: 3. Insertion force test: Steel test pin diameter: .0370 +.0001 inch (0.940 mm +.002 mm). Insertion depth: .050/.075 inch (1.27 mm/1.90 mm). Test pin finish: 16 m
19、icroinches (0.406 mm). Insertion force: 2 pounds (8.90 N), maximum. Withdrawal force test: Steel test pin diameter: .0355 -.0001 inch (0.902 mm -.002 mm). Insertion depth: .050/.075 inch (1.27 mm/1.90 mm). Test pin finish: 16 microinches (0.406 mm). Withdrawal force: 1 ounce (.28 N), minimum. Coupli
20、ng proof torque: Not applicable. Permeability of non-magnetic materials: Applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Insulation resistance: In accordance with MIL-PRF-39012, 5,000 megohms. Center contact retention: Axial force: 6 pounds, minimum. Mois
21、ture resistance: In accordance with MIL-STD-202, method 106. No measurements at high humidity. Insulation resistance shall be 200 megohms minimum within 5 minutes of removal from humidity. Contact resistance (in milliohms, maximum): Initial After environment Center contact: 3 4 Outer contact: 2 N/A
22、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 7 Dielectric withstanding voltage at sea level: 1/ Applies to all dash numbers in the referenced s
23、pecification sheet. Thermal shock: In accordance with MIL-STD-202, method 107, test condition B. Salt spray: In accordance with MIL-PRF-39012. Vibration: In accordance with MIL-STD-202, method 204, test condition D. Shock: In accordance with MIL-STD-202, method 213, test condition I. Corona (at 70,0
24、00 feet): 1/ Applies to all dash numbers in the referenced specification sheet. RF high potential withstanding voltage: Test frequency: 5 to 7.5 MHz. Leakage: Not applicable. 1/ Applies to all dash numbers in the referenced specification sheet. VSWR: 1.20:1, DC to 12.4 GHz (M17/133-RG405 and all das
25、h numbers on the specification sheet). 1.18:1, DC to 12.4 GHz (M17/130-RG402 and all dash numbers on the specification sheet). Cable 1/ V rms, minimum M17/133-RG405 1,000 M17/130-RG402 1,500 Cable 1/ V rms, minimum M17/133-RG405 250 M17/130-RG402 375 Cable 1/ V rms, minimum (at sea level) M17/133-RG
26、405 670 M17/130-RG402 1,000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 8 RF leakage: -90 dB, minimum at 2 GHz. Insertion loss: .03 F (F in GH
27、z). Additive phase noise: Frequency of interest Allowed phase noise (dBc/Hz, max. 10 Hz -84 20 Hz -96 50 Hz -112 100 Hz -113 1 KHz -115 10 KHz -115 The phase noise through the Cabled Connector Under Test (CCUT) will be compared to the phase noise of the signal generator. The phase noise of the test
28、system is measured and must be at least 10 dB below the test limits. The CCUT is connected to the test system and the phase is adjusted for quadrature at the detector. The vibration table is energized and the detector is monitored during vibration over the frequency range of interest. Following comp
29、letion of the vibration sequence the data is collected and plotted vs. frequency. Cable retention force: 1/ Applies to all dash numbers in the referenced specification sheet. 2/ Torque to be applied 4 inches maximum from the end of the connector. Reverse bend not applicable. Connector durability: 50
30、0 cycles minimum, at 12 cycles per minute maximum. Connectors must meet force to engage and disengage after cycling. Coupling mechanism retention force: Not applicable. Part or Identifying Number (PIN): PIN Keying configuration Cable accommodation 05005ZSG-1 A MIL-DTL-17/133 05005ZSG-2 A MIL-DTL-17/
31、130 05005ASG-3 B MIL-DTL-17/133 05005ZSG-4 B MIL-DTL-17/130 05005ZSG-5 C MIL-DTL-17/133 05005ZSG-6 C MIL-DTL-17/130 05005ZSG-7 D MIL-DTL-17/133 05005ZSG-8 D MIL-DTL-17/130 Cable 1/ Pounds (minimum) Torque 2/ Inch-ounce M17/133-RG405 30 16 M17/130-RG402 60 55 Provided by IHSNot for ResaleNo reproduct
32、ion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 05005 REV B PAGE 9 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requir
33、ements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 05005ZSG-1 95077 8721-6005 05005ZSG-2 8721-6006 05005ZSG-3 8722-60011 05005ZSG-4 8721-60036 05005ZSG-5 8721-60037 05005ZSG-6 8721-600
34、38 05005ZSG-7 8721-60039 05005ZSG-8 8721-60040 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor Name and number address 95077 S/V Microwave 2400 Centrepark West Dr. STE. 100 West Palm Beach, Fl 33409 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1