DLA DSCC-DWG-05009 REV B-2012 RESISTOR FIXED FILM CHIP (MELF) 1 4 WATT STYLE 0204.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new vendor. Add pure tin, manufacturer eligibility, and high power pulse paragraphs. Editorial changes throughout. 8 DEC 09 M. Radecki B Add vendors manufacturing plant. Editorial changes throughout. 8 MAR 12 M. Radecki Prepared in accordance with ASME

2、Y14.100 Source control drawing REV STATUS OF PAGES REV B B B B B B B PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Andrew Ernst DESIGN ACTIVITY: DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 4 March 2005 CHECKED BY Andrew Ernst TITLE RESISTOR, FIXED, FILM, CHIP (MELF), 1/4 WATT, S

3、TYLE 0204 APPROVED BY Kendall Cottongim SIZE A CODE IDENT. NO. 037Z3 DWG NO. 05009 REV B PAGE 1 OF 7 AMSC N/A 5905-2012-E01 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitt

4、ed without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, film, chip resistor (MELF), style 0204. 1.2 Part or Identifying Number (PIN). The complete PI

5、N is as follows: 05009 - * * * I I I I I I I I Drawing Resistance value Characteristic Tolerance number (see 3.3.1) (see 3.3.2) (see 3.3.3) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include

6、 documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of

7、 this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents

8、 are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Fixed, Film, Chip, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans

9、and Procedures. MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available

10、 online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document

11、 and the references cited herein (except for related, specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual

12、item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.3 Electrical characteristics. Provided by IHSNot for ResaleNo reproduction or networking pe

13、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAGE 3 Inches mm .015 0.40 .039 1.00 .053 1.35 .137 3.50 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Tolerances

14、 shall be .015 inch (0.40 mm). FIGURE 1. Chip resistor. 3.3.1 Resistance. The nominal resistance expressed in ohms is identified by four digits; the first three digits represent significant figures and the last digit specifies the number of zeros to follow. When the value of resistance is less than

15、100 ohms, or fractional values of an ohm are required, the letter “R“ shall be substituted for one of the significant figures. The resistance value designations are shown in table I. Minimum and maximum resistance values shall be as specified in 3.3.1.1. Resistance values not listed in table IV of M

16、IL-PRF-55342 for the appropriate resistance tolerance shall be considered nonconforming to the specification. TABLE I. Resistance value designations. Designation Resistance ohms 10R0 to 98R8 inclusive 1000 to 9880 inclusive 1001 to 9881 inclusive 1002 to 9882 inclusive 1003 to 9883 inclusive 1004 10

17、.0 to 98.8 inclusive 100 to 988 inclusive 1,000 to 9,880 inclusive 10,000 to 98,800 inclusive 100,000 to 988,000 inclusive 1,000,000 3.3.1.1 Resistance range. Minimum and maximum resistance shall be in accordance with table II. 3.3.2 Resistance characteristic. The resistance characteristic shall be

18、in accordance with table II. 3.3.3 Resistance tolerance. The resistance tolerances shall be in accordance with table II. 3.4 Termination material. Termination material shall be in accordance with MIL-PRF-55342, code letter B. Provided by IHSNot for ResaleNo reproduction or networking permitted witho

19、ut license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAGE 4 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exce

20、ed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6 Voltage rating. The continuous voltage shall not exceed 200 volts. 3.7 Power rating. The power rating shall be 0.25 watt from -55C to +70C. For operation at temperatures higher than +70C, derate in

21、accordance with figure 2. 3.8 Temperature range. The temperature range shall be -55C to +125C. 3.9 Marking. Marking of the individual chip resistors is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manu

22、facturers name or Commercial and Government Entity (CAGE) code, date, and lot codes. The body may be color coded as called out in MIL-STD-1285 or the manufacturers catalog. TABLE II. Resistance characteristics, tolerances, and range. Characteristics Tolerances Resistance range (ohms) Symbol ppm/C Sy

23、mbol percent Minimum Maximum B 5 A 0.05 100 600K B 0.10 C 0.25 D 0.50 F 1.00 C 10 A 0.05 100 600K B 0.10 C 0.25 D 0.50 F 1.00 D 15 A 0.05 100 600K B 0.10 C 0.25 50 600K D 0.50 F 1.00 E 25 A 0.05 100 600K B 0.10 C 0.25 50 600K D 0.50 20 600K F 1.00 H 50 A 0.05 100 600K B 0.10 C 0.25 50 800K D 0.50 10

24、 1M F 1.00 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically

25、 advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAGE 5 * 3.11 Manufacturer eligibility. To be eligible for listing as an ap

26、proved source of supply, a manufacturer shall perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VAT 3.11.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting

27、to be an approved source of supply. 3.12 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. FIGURE 2. Derating curve

28、for high ambient temperatures. 4.2 Reliability assurance program. The reliability assurance provisions specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 are not applicable to this document. 4.3 Product level qualification. Product level qualification specified in MIL-PRF-55342

29、 and MIL-STD-690 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (ER level) and group B inspections. 4.4.1.1 Group A inspection. Group A inspection (ER level) shall be in accordance

30、with MIL-PRF-55342. PPM testing and verification as specified in MIL-PRF-55342 are not applicable to this document. 4.4.1.2 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-55342, subgroup 1 only. 4.4.1.2.1 Certification. The acquiring activity, at its discretion, may accep

31、t a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAG

32、E 6 4.4.1.3 Visual and mechanical inspection. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements 3.2, 3.9, and 3.12. 4.5 Inspection of packaging. Inspection of packaging shal

33、l be in accordance with MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the

34、 responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from t

35、he managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The chip r

36、esistors described herein are intended to be used in thick or thin film circuits where microcircuitry is intended; also for use in surface mounting applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: O

37、ne copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of comp

38、liance with group B requirements (see 4.4.1.2.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical

39、 operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, r

40、efer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when orderi

41、ng or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 that specifies a preventive packaging procedure. 6.5 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for

42、 such applications, damage and premature failure are possible. These resistors only see a one-time pulse (Short-time overload) as part of the group B inspection of MIL-PRF-55342. * 6.6 User of record. Coordination of this document for future revisions is coordinated only with the approved source of

43、supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. Provided by IH

44、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 05009 REV B PAGE 7 * 6.7 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as t

45、hey become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing PIN Vendors similar designation or t

46、ype number 1/ Vendor CAGE Vendors name and address 05009-* SMC0204 20940 Micro-Ohm Corporation 1088 Hamilton Road Duarte, CA 91010 Plant: Hikou, Hsin Chu Hsien, 300 Taiwan 05009-* MGP5009 56637 RCD Components, Inc. 520 East Industrial Park Dr. Manchester, NH 03109 Plant: Taipei, 10682 Taiwan 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-