DLA DSCC-DWG-07016 REV C-2013 CAPACITOR FIXED TANTALUM CHIP WEIBULL GRADED LOW ESR.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added parts from Kemet. 20 January 2011 Michael A. Radecki B Updated table II for vendor B. 21 February 2012 Michael A. Radecki C Updated table II for vendor B. 10 July 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV

2、 C C C C C C C C C C C C C PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Ken Bernier DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 30 March 2007 CHECKED BY Patrick Kyne TITLE CAPACITOR, FIXED, TANTALUM CHIP, WEIBULL GRADED, LOW ESR APPROVED BY Micha

3、el A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 07016 SCALE N/A REV C PAGE 1 OF 13 AMSC N/A 5910-2013-E16 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DESI N AC VI CAGE C DE 0Provided by IHSNot for ResaleNo reproduction or networkin

4、g permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-55365 describe the complete requirements for low ESR tantalum chip capacitors. 1.2 Part or Identifying Number (P

5、IN). The complete PIN is as follows: 07016- 001 K B C A Drawing Dash Capacitance Reliability Termination Surge current number number tolerance grade finish option (see table I) (see 1.2.1) (see 1.2.2) (see 1.2.3) (see 1.2.4) 1.2.1 Capacitance tolerance. The capacitance tolerance is identified by a s

6、ingle letter as follows: K = 10 percent, M = 20 percent. 1.2.2 Reliability grade. The reliability grade (Weibull failure rate level (FRL) is identified by a single letter as follows (%/1,000 hours): B = 0.1, C = 0.01, and D = 0.001. 1.2.3 Termination finish. The termination finish is identified by a

7、 single letter as follows: B = gold plated (50 microinch minimum), H = solder plated (100 microinch minimum), and C = hot solder dip (60 microinch minimum). 1.2.4 Surge current option. The optional surge current testing is identified by a single letter as described in MIL-PRF-55365 and as follows: A

8、 B, C, or Z. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every

9、 effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications standards and handboo

10、ks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55365 - Capacitor,

11、 Fixed, Electrolytic (Tantalum), Chip, Established Reliability, Nonestablished Reliability, and High Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts, Test Methods for. (Copies of these documents are available online at h

12、ttp:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited h

13、erein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COL

14、UMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 3 Case Size Length (L) Width (W) Height (H) Term Width W1 0.10 (.004) Term Length A 0.30 (.012) S Min. A 3.200.20 (.126.008) 1.600.20 (.063.008) 1.600.20 (.063.008) 1.20 (.047) 0.80 (.031) 0.80 (.031) B 3.500.20 (.138.008) 2.8

15、00.20 (.110.008) 1.900.20 (.075.008) 2.20 (.087) 0.80 (.031) 1.10 (.043) C 6.000.30 (.236.012) 3.200.30 (.126.012) 2.500.30 (.098.012) 2.20 (.087) 1.30 (.051) 2.50 (.098) D 7.300.30 (.287.012) 4.300.30 (.169.012) 2.800.30 (.110.012) 2.40 (.094) 1.30 (.051) 3.80 (.150) E 7.300.30 (.287.012) 4.300.30

16、169.012) 4.000.30 (.157.012) 2.40 (.094) 1.30 (.051) 3.80 (.150) V 7.300.30 (.287.012) 6.100.20 (.240.008) 3.450.30 (.136.012) 3.10 (.120) 1.40+0.30/-0.20 (.055+.012/-.008) 3.60 (.142) NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are in parentheses and are given for information onl

17、y. 3. The anode (+) terminal shall be indicated by a stripe marked on the top surface at the anode end. 4. Solderable surfaces are only those surfaces designated as such. Termination edges are not considered solderable. 5. Notch at option of the manufacturer. 6. When solder coated terminations are r

18、equired, add an additional .015 inches (0.38 mm) to the above listed tolerances for “L”, “W” and “H” for each case size. 7. The W1dimension applies to the termination width for the “A” dimensional area only. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or netw

19、orking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 4 TABLE I. Electrical characteristics. DSCC drawing PIN 1/ 07016- Cap (nom) uF Rated Voltage V dc DCL DF ESR 100 kHz +25C Case Size +25C +85C +125 C +25C

20、85/+125C -55C (A) (A) (A) (%) (%) (%) mOhms 001- 33 4 1.4 14 17 6 9 9 3000 A 002- 68 4 2.7 27 32 10 12 14 1500 A 003- 100 4 4 40 48 30 36 42 1400 A 004- 100 4 4 40 48 8 10 12 900 B 005- 1000 4 40 400 480 60 90 90 200 E 006- 3.3 6.3 0.5 5 6 6 9 9 8000 A 007- 4.7 6.3 0.5 5 6 6 9 10 6000 A 008- 6.8 6.

21、3 0.5 5 6 6 9 10 5000 A 009- 10 6.3 0.6 10 8 6 9 10 4000 A 010- 15 6.3 0.9 10 11 6 9 10 3500 A 011- 22 6.3 1.4 14 17 6 9 10 3000 A 012- 22 6.3 1.4 14 17 6 9 10 600 B 013- 33 6.3 2.1 21 25 6 9 10 600 B 014- 47 6.3 3.0 30 36 6 9 10 300 C 015- 68 6.3 4.3 43 51 8 10 12 500 B 016- 68 6.3 4.3 43 51 6 9 10

22、 200 C 017- 100 6.3 6.3 63 76 6 9 10 150 C 018- 100 6.3 6.3 63 76 6 9 10 75 C 019- 150 6.3 9.5 95 113 6 9 10 125 D 020- 220 6.3 13.9 139 166 8 10 12 125 D 021- 330 6.3 20.8 208 249 8 10 12 150 E 022- 330 6.3 20.8 208 249 8 10 12 50 E 023M- 470 6.3 29.6 296 355 10 12 14 200 E 024M- 470 6.3 29.6 296 3

23、55 10 12 14 50 E 025- 470 6.3 29.6 296 355 10 12 12 40 V 026- 4.7 10 0.5 5 6 6 9 10 5000 A 027- 6.8 10 0.7 7 8 6 9 10 4000 A 028- 10 10 1 10 12 6 9 10 3000 A 029- 10 10 1 10 12 6 9 10 1800 A 030- 15 10 1.6 16 19 6 9 10 3200 A 031- 15 10 1.6 16 19 6 9 10 1000 A 032- 15 10 1.6 16 19 6 9 10 600 B 033-

24、22 10 2.2 22 26 6 9 10 700 B 034- 22 10 2.2 22 26 6 9 10 500 B 035- 22 10 2.2 22 26 6 9 10 300 C 036- 33 10 3.3 33 40 8 10 12 700 A 037- 33 10 3.3 33 40 6 9 10 650 B 038- 33 10 3.3 33 40 6 9 10 425 B 039- 33 10 3.3 33 40 6 9 10 500 C 040- 47 10 4.7 47 56 6 9 10 350 C 041- 47 10 4.7 47 56 6 9 10 200

25、C 042- 68 10 6.8 68 82 8 10 12 300 C 043- 68 10 6.8 68 82 8 10 12 80 C 044- 68 10 6.8 68 82 6 9 10 150 D 045- 100 10 10 100 120 8 10 12 200 C See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBU

26、S COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 5 TABLE I. Electrical characteristics. - Continued. DSCC drawing PIN 1/ 07016- Cap (nom) uF Rated Voltage V dc DCL DF ESR 100 kHz +25C Case Size +25C +85C +125 C +25C +85/+125 C -55C (A) (A) (A) (%) (%) (%) mOhms 046- 100 10 10 10

27、0 120 8 10 12 75 C 047- 100 10 10 100 120 6 9 10 50 D 048- 150 10 15 150 180 8 10 12 50 D 049- 220 10 22 220 264 8 10 12 150 D 050M- 220 10 15 150 180 8 10 12 50 D 051- 220 10 22 220 264 8 10 12 50 E 052M- 330 10 33 330 396 8 10 12 150 D 053M- 330 10 33 330 396 8 10 12 50 D 054- 330 10 33 330 396 8

28、10 12 100 E 055- 330 10 33 330 396 8 10 12 50 E 056- 330 10 33 330 396 8 10 12 40 V 057M- 470 10 47 470 564 10 12 14 200 E 058M- 470 10 47 470 564 10 12 14 50 E 059- 470 10 47 470 564 10 12 14 40 V 060- 2.2 16 0.5 5 6 6 9 10 5500 A 061- 3.3 16 0.5 5 6 6 9 10 5000 A 062- 3.3 16 0.5 5 6 6 9 10 3500 A

29、063- 4.7 16 0.8 8 10 6 9 10 2000 A 064- 6.8 16 1.1 11 13 6 9 10 1500 A 065- 6.8 16 1.1 11 13 6 9 10 1200 B 066- 10 16 1.6 16 19 6 9 10 3000 A 067- 10 16 1.6 16 19 6 9 10 900 B 068- 15 16 2.4 24 29 6 9 10 800 B 069- 15 16 2.4 24 29 6 9 10 500 B 070- 22 16 3.6 36 43 6 9 10 600 B 071- 22 16 3.6 36 43 6

30、 9 10 375 C 072- 22 16 3.6 36 43 6 9 10 150 C 073- 22 16 3.6 36 43 6 9 10 500 B 074- 33 16 5.3 53 64 6 9 10 300 C 075- 33 16 5.3 53 64 6 9 10 100 C 076- 47 16 7.6 76 91 6 9 10 350 C 077- 47 16 7.6 76 91 6 9 10 110 C 078- 47 16 7.6 76 91 6 9 10 80 D 079- 68 16 10.9 109 131 6 9 10 150 D 080- 100 16 16

31、 160 192 6 9 10 125 D 081- 100 16 16 160 192 6 9 10 50 D 082M- 150 16 24 240 288 6 9 10 150 D 083M- 150 16 24 240 288 6 9 10 60 D 084- 150 16 24 480 288 6 8 10 45 V 085- 220 16 35.2 352 422 8 10 12 50 V 086- 1.5 20 0.5 5 6 6 8 10 6500 A 087- 2.2 20 0.5 5 6 6 8 10 3000 A 088- 4.7 20 1 10 12 6 8 10 40

32、00 A 089- 4.7 20 1 10 12 6 8 10 1800 A 090- 4.7 20 2 20 24 6 8 10 1000 B See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE

33、 6 TABLE I. Electrical characteristics. - Continued. DSCC drawing PIN 1/ 07016- Cap (nom) uF Rated Voltage V dc DCL DF ESR 100 kHz +25C Case Size +25C +85C +125 C +25C +85/+125 C -55C (A) (A) (A) (%) (%) (%) mOhms 091- 6.8 20 1.4 14 17 6 8 10 1000 B 092- 10 20 0.7 7 8 6 8 10 1000 B 093- 10 20 0.7 7

34、8 6 8 10 500 B 094- 10 20 1.4 14 17 6 8 10 700 C 095- 15 20 3 30 36 6 8 10 500 B 096- 15 20 3 30 36 6 8 10 450 C 097- 22 20 4.4 44 53 6 8 10 600 B 098- 22 20 4.4 44 53 6 8 10 400 C 099- 33 20 6.6 66 79 6 8 10 300 C 100- 33 20 6.6 66 79 6 8 10 200 D 101- 33 20 6.6 66 79 6 8 10 100 D 102- 47 20 9.4 94

35、 113 6 8 10 200 D 103- 47 20 9.4 94 113 6 8 10 100 D 104- 68 20 13.6 136 163 6 8 10 200 D 105- 68 20 13.6 136 163 6 8 10 70 D 106- 68 20 13.6 136 163 6 8 10 200 E 107- 100 20 20 200 240 8 10 12 60 V 108M- 0.68 25 0.5 5 6 4 6 8 10000 A 109- 1.0 25 0.5 5 6 4 6 8 8000 A 110- 1.5 25 0.5 5 6 6 8 10 7500

36、A 111- 1.5 25 0.5 5 6 6 8 10 3000 A 112- 2.2 25 0.5 5 6 6 8 10 7000 A 113- 2.2 25 0.5 5 6 6 8 10 2000 B 114- 3.3 25 0.5 5 6 6 8 10 2000 B 115- 4.7 25 1.2 12 14 6 9 10 3100 A 116- 4.7 25 1.2 12 14 6 8 10 1500 B 117- 4.7 25 1.2 12 14 6 8 10 700 B 118- 6.8 25 1.7 17 20 6 8 10 2800 B 119- 6.8 25 1.7 17

37、20 6 8 10 700 B 120- 6.8 25 1.7 17 20 6 8 10 700 C 121- 10 25 2.5 25 30 6 8 10 500 C 122- 10 25 2.5 25 30 6 8 10 300 C 123- 22 25 5.5 55 66 6 8 10 400 C 124- 22 25 5.5 55 66 6 8 10 275 C 125- 22 25 5.5 55 66 6 8 10 200 D 126- 22 25 5.5 55 66 6 8 10 100 D 127- 33 25 8.3 83 100 6 8 10 300 D 128- 33 25

38、 8.3 83 100 6 8 10 90 D 129- 33 25 8.3 83 100 6 8 10 100 E 130M- 47 25 11.8 118 142 6 8 10 250 D 131M- 47 25 11.8 118 142 6 8 10 175 D 132- 68 25 17 170 204 8 10 12 95 V 133M- 0.47 35 0.5 5 6 4 6 8 12000 A 134M- 0.68 35 0.5 5 6 4 6 8 8000 A 135- 1.0 35 0.5 5 6 4 6 6 7500 A See footnote at end of tab

39、le. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 7 TABLE I. Electrical characteristics. - Continued. DSCC drawing PIN 1/ 07016- Cap (nom) uF Rated

40、Voltage V dc DCL DF ESR 100 kHz +25C Case Size +25C +85C +125 C +25C +85/+125 C -55C (A) (A) (A) (%) (%) (%) mOhms 136- 1.5 35 0.5 5 6 6 8 9 7500 A 137- 1.5 35 0.5 5 6 6 8 9 5200 B 138- 2.2 35 0.8 8 10 6 8 9 2000 B 139- 3.3 35 1.2 12 14 6 8 9 1000 B 140- 4.7 35 1.6 16 19 6 8 9 1500 B 141- 4.7 35 1.6

41、 16 20 6 8 9 450 D 142- 6.8 35 2.4 24 29 6 9 9 350 C 143- 6.8 35 2.4 24 29 6 9 9 400 D 144- 10 35 3.5 35 42 6 9 9 1600 C 145- 10 35 3.5 35 42 6 9 9 125 D 146- 15 35 5.3 53 64 6 9 9 450 C 147- 15 35 5.3 53 64 6 9 9 300 D 148- 15 35 5.3 53 64 6 9 9 100 D 149- 22 35 7.7 77 92 6 9 9 400 D 150- 22 35 7.7

42、 77 92 6 9 9 125 D 151- 22 35 7.7 77 92 6 9 9 125 E 152M- 33 35 11.6 116 139 6 9 9 300 D 153M- 33 35 11.6 116 139 6 9 9 200 D 154M- 33 35 11.6 116 139 6 9 9 300 E 155M- 47 35 16.5 165 197 6 9 9 250 E 156M- 47 35 16.5 165 197 6 9 9 200 V 157M- 0.15 50 0.5 5 6 4 6 6 15000 A 158M- 0.22 50 0.5 5 6 4 6 6

43、 18000 A 159- 0.47 50 0.5 5 6 4 6 6 9500 A 160- 0.47 50 0.5 5 6 4 6 6 9500 B 161- 0.68 50 0.5 5 6 4 6 6 7900 A 162M- 1.0 50 0.5 5 6 4 6 6 6600 A 163- 1.0 50 0.5 5 6 4 6 6 7000 B 164- 1.5 50 0.8 8 10 6 8 9 2000 C 165- 1.5 50 0.8 8 10 6 8 9 1500 D 166- 2.2 50 1.1 11 13 6 8 9 1200 D 167- 3.3 50 1.7 17

44、20 6 9 9 800 D 168- 4.7 50 2.4 24 29 6 9 9 300 D 169- 6.8 50 3.4 34 41 6 6 6 600 D 170- 6.8 50 3.4 34 41 6 6 6 300 D 171- 6.8 50 3.4 34 41 6 6 6 400 E 1/ Complete PIN shall include additional symbols to indicate capacitance tolerance (where applicable), reliability grade, termination finish, and sur

45、ge current option. (see 1.2) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 07016 REV C PAGE 8 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface an

46、d physical dimensions shall be as specified herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally or externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a mini

47、mum of 3 percent lead by mass (see 6.3). 3.1.2 Operating temperature range. The capacitors are rated for their given voltages from -55C to +85C. They are derated two thirds of their given voltages at +125C. See table I. 3.2 Electrical characteristics. 3.2.1 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202. Maximum dc bias shall be 2.2 volts