DLA DSCC-DWG-09001 REV B-2013 CABLE FIBER OPTIC MIXED FIBER (MULTIMODE AND SINGLE MODE FIBERS).pdf

1、 AMSC N/A 6015-2013-E01 REVISIONS LTR DESCRIPTION DATE APPROVED A 1) Change “hybrid” to “mixed fiber”. Per JFOWG (military Joint Fiber Optic Working Group), the following terminology has been established, Cables, Hybrid - contain both optical fibers and metallic conductors, Cables, Mixed Fiber - con

2、tain more than one size and/or type of optical fiber. 2) Delete rip cord from figure 1. Cable does not include a rip cord. 3) Revise table II to add 62.5 m fiber column and its associated optical characteristics. 4) Replace text of paragraph 3.9 “crush resistance” with text from MIL-PRF-85045. 5) Pa

3、ragraph 3.3, revise “Material”. 6) Delete dynamic bend, paragraph 3.13. Not applicable to MIL-PRF-85045/8 cable. 7) Paragraph 3.21, change “method a procedure I” to change “method A procedure I”. 8) Insert new paragraph between 3.9 and 3.10, new requirement “Crosstalk. Crosstalk shall be performed d

4、uring the application of the crush resistance load.” 9) Revise paragraph 6.5 to specify approved source of supply and add table V providing OCC information as approved source of supply. 2 November 2011 M. Radecki B Revised table V to add Draka Cableteq as approved source of supply. 31 May 2013 M.Rad

5、ecki ALL SHEETS ARE REVISION B Prepared in accordance with ASME Y14.100 PMIC N/A PREPARED BY Eugene A. Ebert DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 7 April 2011 CHECKED BY Eugene A. Ebert TITLE CABLE, FIBER OPTIC, MIXED FIBER (MULTIMODE AND SINGLE MODE

6、 FIBERS) APPROVED BY Michael A Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09001 SCALE N/A REV B PAGE 1 OF 7 Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09001 REV B PAGE 2 SCOPE 1.1 Scope. This drawing describes the requirements for mix

7、ed fiber optic cable for ground tactical application. The mixed fiber cable detailed in this drawing consists of two multimode and two single mode optical fibers. Buffer colors identify individual fibers. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 09001 - XX Drawing

8、Dash number number (see table I) TABLE I. Dash number. Dash number Fibers (MM and SM) 01 50/125 and 9/125 02 62.5/125 and 9/125 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents c

9、ited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specif

10、ication, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those c

11、ited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49291 - Fiber, Optical, (Metric), General Specification For. MIL-PRF-85045 - Cables, Fiber Optic (Metric), General Specification For. DEPARTMENT OF DEFENSE STANDARD MIL-STD-1285 - Marking of Electrical and Electronic

12、Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent spec

13、ified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL ASTM - D470 - Wire and Cable, Crosslinked Insulations and Jackets for. Copies of this document are available online at http:/www.astm.org or from ASTM Internati

14、onal, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09001 REV B PAGE 3 TELECOMMUNICATIONS INDUSTRY ASSOCIAT

15、ION TIA 455.41 - Fiber Optic Cables, Compressive Loading Resistance Of. Copies of this document is available online at http:/www.tiaonline.org or from Telecommunications Industry Association, 1320 North Courthouse Road, Suite 200, Arlington, Virginia 22201. 2.4 Order of precedence. Unless otherwise

16、noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. R

17、EQUIREMENTS 3.1 General. The requirements for acquiring the product described herein shall consist of this drawing and MIL-PRF-85045. 3.2 Interface and physical dimensions. See figure 1. NOTE: 1. Dimensions are in millimeters, inch equivalents are given for reference purposes only. FIGURE 1. Mixed f

18、iber cable. 3.3 Material. 3.3.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and prom

19、otes economically advantageous life cycle costs. 3.3.2 Materials. See MIL-PRF-85045/8. Dimensions A B C 5.8 0.15 2.9 0.15 0.9 0.05 mm Inches 0.05 0.002 0.15 0.006 0.9 0.035 2.9 0.114 5.8 0.23 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDLA LAND AND MA

20、RITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09001 REV B PAGE 4 3.4 Fibers. a. Type: Two multimode 50/125 fibers in accordance with MIL-PRF-49291/1 and two single mode 9/125 fibers in accordance with MIL-PRF-49291/7 (see table I dash number 01), or two multimode 62.5/125 fibers in accor

21、dance with MIL-PRF-49291/6 and two single mode 9/125 fibers in accordance with MIL-PRF-49291/7 (see table I dash umber 02) shall be used. b. Colors: c. Buffer diameter: 900 m 0.05 m. 3.5 Cable weight. Cable weight shall be 31 kg/km maximum. 3.6 Tensile load. Tensile load shall be 1,800 N max during

22、installation and 600 N max during operation. 3.7 Bend radius. Bend radius shall be 8.7 cm minimum during installation and 5.8 cm during operation (corner bend 3.13). 3.8 Impact resistance. The impact resistance shall be 100 impacts at 25C and 50 impacts at -46C to 71C. 3.9 Crush. Compressive loading

23、 testing shall be accomplished in accordance with TIA 455.41 for the finished cable. The following special test conditions shall apply: a. The compressive load exposure shall be not less than 2,000 N/cm times the cable outer diameter (in cm), held for 3 minutes, and released. b. The compressive load

24、ing rate shall be not less than 2,000 N/min. c. The change in optical transmittance shall be measured while the specimen is under load and after load removal. Visual inspection of the specimen shall be made under 10X magnification after load removal. d. A break in any fiber caused by this test shall

25、 be a failure of the cable. e. Optical crosstalk shall be monitored in accordance with 3.10. 3.10 Crosstalk. Crosstalk shall be measured during the application of the crush resistance load. 3.11 Temperature ranges. a. Operating: -46C (-51F) to +71C (160F). b. Storage: -55C (-67F) to +85C (185F). Fib

26、er (m) Colors Multimode (50/125) blue, orange Multimode (62.5/125) aqua, rose Single mode (9/125) green, brown Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09001 REV B PAGE 5 3.12

27、 Optical characteristics. For optical characteristics, see table II. TABLE II. Optical characteristics. 50m 62.5 m Single mode Wavelength 20 nm 850 nm 1,300 nm 850 nm 1,300 nm 1,310 nm 1,550 nm Attenuation (max) 3.5 dB/km 1.0 dB/km 3.75 dB/km 1.5 dB/km 0.5 dB/km 0.5 dB/km Bandwidth (min) 500 MKz-km

28、500 MKz-km 300 MKz-km 600 MKz-km - - Zero dispersion slope at 1,312 nm 20 nm N/A N/A N/A N/A 0.092 ps/(nm2-km) 3.13 Corner bend. Applicable except the load shall be 500 N. 3.14 Temperature cycling. Change in optical transmittance measurements may be made periodically. At a minimum, one optical measu

29、rement shall be made over a period of 1 hour at the end of each temperature plateau. 3.15 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-85045 Qualified Products Listing (http:/www.landandmaritime.dla.mil/programs/q

30、mlqpl) for at least one cable product and submit results of tests specified herein (see 4.1 and table III) to: DLA Land and Maritime-VQP, P. O. Box 3990, Columbus, Ohio 43218-3990. 3.16 Certificate of compliance. Upon request, approved manufacturers shall provide a certificate of compliance. 3.17 Ma

31、rking. Marking shall be in accordance with MIL-STD-1285, except the mixed fiber optic cable shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.17.1 Marking durability. Applicable, except the applie

32、d mass shall be 100 grams. 3.18 Thermal shock. Applicable, except schedule A shall be used. 3.19 Barometric pressure (reduced). a. Operating: 3,000 m (test condition letter B). b. Nonoperating: 12,200 m. 3.20 Life aging. Test exposure time shall be 240 hours at 110C (230F). 3.21 Freezing water immer

33、sion. Applicable, except method A procedure I shall be used. 3.22 Flame extinguish. Not applicable. 3.23 Smoke propagation and flame extinguish. Not applicable. 3.24 Shock. Not applicable. 3.25 Water absorption. Applicable except the sample size shall be in accordance with ASTM-D470 and test shall b

34、e performed in accordance with the gravimetric method of ASTM-D470. 3.26 Paint susceptibility. Not applicable. 3.27 Halogen content. Not applicable. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09001 REV B PAGE 6 3.28 Toxicity. Not applic

35、able. 3.29 Workmanship. The cable shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling and inspection procedures shall be performed in accordance with MIL-PRF-8504

36、5. For approval testing see table III, for conformance testing see table IV. TABLE III. Approval testing. 1/ Requirement Test 3.2 Interface and physical dimensions 3.3 Recycled, recovered or environmentally preferred material 3.4 Fibers 3.5 Cable weight 3.6 Tensile load 3.7 Bend radius 3.8 Impact re

37、sistance 3.9 Crush 3.10 Crosstalk 3.12 Optical characteristics 1/ For approval, sample must pass these tests. TABLE IV Conformance inspection. Requirement Inspection 3.2 Interface and physical dimensions 3.4 Fibers 3.5 Cable weight 3.12 Optical characteristics 5. PACKAGING 5.1 Packaging. For acquisi

38、tion purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging

39、 requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files,

40、 CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDEN

41、T NO. 037Z3 DWG NO. 09001 REV B PAGE 7 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection wit

42、h each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Governme

43、nt assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 6.4 Users of record. Coordin

44、ation of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at FiberOpticGroupdla.mil or if in writing to: DLA Land and Maritime, ATTN: D

45、LA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0571 or DSN 850-0571. 6.5 Approved source(s) of supply. Current approved source(s) of supply are listed in table V. Additional sources will be added as they become available. Assistance in the use of th

46、is drawing may be obtained online at FiberOpticGroupdla.mil , or by contacting Defense Supply Center, Columbus, ATTN: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0571 or DSN 850-0571. TABLE V Approved source(s) of supply. DLA Land and Maritime d

47、rawing PIN 1/ Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 09001-01 OC-0003480 6Y528 Optical Cable Corporation 5290 Concourse Drive Roanoke, VA 24019 http:/ 09001-02 OC-0003479 6Y528 Optical Cable Corporation 5290 Concourse Drive Roanoke, VA 24019 http:/ 09001-01

48、H1537-S1032T-04 71102 Draka Cableteq 22 Joseph E. Warner Blvd. North Dighton, MA 02764 09001-02 H1538-S1032T-04 71102 Draka Cableteq 22 Joseph E. Warner Blvd. North Dighton, MA 02764 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for Resale-,-,-