DLA DSCC-DWG-09003 REV A-2009 SWITCHES DUAL IN-LINE PACKAGE (DIP) ROCKER ACTUATOR STANDARD PROFILE SINGLE POLE SINGLE THROW STATIONS SEALED BASE [Superseded DLA MIL-PRF-83504 1 D C.pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Pin detail changed. 2/9/09 Michael A. RadeckiPrepared in accordance with ASME Y14.100 Source Control drawing REV STATUS REV A A A A A A A A OF PAGES PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Mark A. Rush DESIGN ACTIVITY DEFENSE SUPPLY CENTER, COLUMBUS COLUM

2、BUS, OH Original date of drawing 20 November 2008 CHECKED BY Mark A. Rush TITLE SWITCHES, DUAL IN-LINE PACKAGE (DIP), ROCKER ACTUATOR, STANDARD PROFILE, SINGLE POLE, SINGLE THROW STATIONS, SEALED BASE APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09003 REV PAGE 1 OF 8 AMSC N/A

3、5930-E039Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. SCOPE 1.1 Scope. This drawing describes the requirements for switches, dual in-line package (DIP), rocker actuator, standard profile, single pole, single throw stations, sealed base. 1.2 Par

4、t or Identifying Number (PIN) The complete PIN is as follows: 09003- XXX Drawing number Dash number See Table 1 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other se

5、ctions of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether

6、 or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the soli

7、citation or contract (See 6.2). DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Components, Test Methods for. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from the Standardization Document Order Des

8、k, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regul

9、ations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified herein (see figure 1). 3.2.1 Pure tin. The us

10、e of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of switch components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (See 6.4). 3.3 Contact resistance, dry circuit. Switches sha

11、ll be subjected to 50 mv maximum open circuit at 50 ma maximum. A minimum of 10 readings shall be measured. Initial measurements shall be less than 50 milliohms and 100 milliohms after testing. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A PAGE 2 Prov

12、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A PAGE 3 .315 0.010 .320 .360 .240 .310 .012 .003 TYP .024 .015 .380.020A MAX SEE DETAIL -A- DETAIL -A- SEE DETAI

13、L -A- DIMPLES OR NOTCHES ACCEPTABLE IN THIS AREA FOR SWITCH ACTUATION NO. OF STATIONS STANDOFF 11 121 2 .100 TYP .005 Inches mm Inches mm .003 0.08 .140 3.56 .005 0.13 .270 6.86 .012 0.30 .300 7.62 .015 0.38 .320 8.13 .020 0.51 .360 9.14 .021 0.53 .380 9.65 .100 2.54 NOTES: 1. Dimensions are in inch

14、es. 2. Metric equivalents are given for general information only. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A P

15、AGE 4 TABLE I. Dash numbers and characteristics 1/ Dash number Number of stations Dimension “A“ inches (mm) 022 2 .280 (7.11)023 3 .380 (9.65)024 4 .480 (12.19)025 5 .580 (14.73)026 6 .680 (17.27)027 7 .780 (19.81)028 8 .880 (22.35)029 9 .980 (24.89)030 10 1.080 (27.43)031 11 1.180 (29.97)032 12 1.2

16、80 (32.51)1/ For cross reference of MIL-PRF-83504, DSCC 09003, and approved source part numbers see 6.3 3.4 Insulation resistance. Test between a minimum of 10 sets of open switches and a minimum of 10 sets of adjacent closed switch contacts. A test voltage of 100 vdc shall be applied for two minute

17、s before resistance is measured. Measurement shall be 1000 megohms minimum. 3.5 Dielectric withstanding voltage. Test between a minimum of 10 sets of open switches and a minimum of 10 sets of adjacent closed switch contacts. Apply 500 vdc dielectric withstanding voltage for 1 minute. 1 ma maximum le

18、akage current. No flashover or corona shall occur. 3.6 Electrical stability. Subject switch to 50 vdc at 1.0 ampere maximum current until temperature stabilizes. When three readings at five minute intervals are the same, the measured temperature rise shall not exceed 30C from ambient. 3.7 Capacitanc

19、e. Test between a minimum of 10 adjacent closed switch circuits. With a frequency of 100kHz applied the capacitance shall not exceed 5 picofarads. 3.8 Solderability. Contact post shall have a minimum of 95% coverage when subjected to immersion in active flux (5 to 10 seconds), allowed to drain (5 to

20、 20 seconds), immersed in molten 60/40 or 63/37 tin lead solder (3 to 5 seconds), and then cleaned using isopropyl alcohol. 3.9 Vibration. Switch shall be subjected to 20 Gs, 10-2000 Hz with 100 ma current applied. The vibrations frequency shall be varied logarithmically between the limits and retur

21、ned to 10 Hz in 20 minutes. The cycle shall be performed 12 times in each of three mutually perpendicular planes, for a total vibration time of 12 hours. There shall be no discontinuities of 10 microseconds or longer in duration. No physical damage shall occur. 3.10 Physical Shock. Switch shall be s

22、ubjected to 50 Gs half-sine shock pulses of 11 milliseconds duration. 3 shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. There shall be no discontinuities of 10 microseconds or longer in duration. No physical damage shall occur. Provided by IHSNot for ResaleNo

23、 reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A PAGE 5 3.11 Resistance to soldering heat. There shall be no physical damage to switch inserted into PC board and immersed in solder bath a

24、t 260C for 10 seconds, switch in the OFF position. 3.12 Terminal strength, pull test. Subject 10 random switch terminals to an axial pull of 2 pounds. No physical damage shall occur. 3.13 Terminal strength, bend test. Subject 10 random switch terminals to two 45 bend cycles, per MIL-STD-202, method

25、211, condition B. No physical damage shall occur. 3.14 Durability. Switch shall be mounted and subjected to 2000 cycles of actuation with a resistive load of 24 vdc and 25 ma maximum current applied. No physical damage shall occur. 3.15 Actuation force. Switch shall be mounted and force applied to a

26、ctuators. 24 ounces maximum per switch actuator initially and after durability. Switch shall be able to withstand a total actuation force of 3 pounds without resulting in improper operation or switch damage. 3.16 Thermal Shock. Subject switches in the ON and OFF condition to 5 non-operating cycles b

27、etween -55C and 105C. Each cycle shall consist of 30 minutes of each temperature with 5 minute transition between temperatures. No physical damage shall occur. 3.17 Humidity-temperature cycling. Subject switch to humidity between 90 and 100% relative humidity (RH) while temperature cycles between 25

28、C and 65C twice in 24 hours. 10 cycles are to be completed. Measure insulation resistance during recovery period. 3.18 Temperature life. Subject switches in the ON condition to temperature life conditions. No physical damage shall occur. 3.19 Mixed flowing gas. Subject switches in ON condition to en

29、vironmental class II for 20 days. Class II is defined as a temperature of 30C and a relative humidity of 70% with pollutants of Cl2at 10 2 ppb, NO2at 200 50 ppb, and H2S at 10 2 ppb. 3.20 Marking. As a minimum, marking shall be include manufacturers name or CAGE code and date code (except -022 and -

30、023 due to space constraints). 3.21 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.22 Manufacturer eligibility: To be eligible for listing as an approved source of supply a manufacturer shall perform group

31、A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.23 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the

32、 material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.24 Workmanship. The switch shall be uniform in quality and free from defects that will affect life, or serviceability. 4. VERIFICATION 4.1 Qualification inspection. Qua

33、lification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE S

34、UPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A PAGE 6 4.2.2 Group A inspection. Group A inspection shall consist of the tests specified in table II in the order shown. TABLE II. Group A inspection Inspection Requirement paragraph Sampling procedure Interface an

35、d physical dimensions. Marking Workmanship 3.2 3.20 3.23 5 samples 0 failures 4.2.3 Group B inspection. Group B inspection shall consist of the tests specified in table III in the order shown. TABLE III. Group B inspection Sample Number 1 2 3 4 5 6 7 Test or Examination Requirement Paragraph Test Se

36、quence 1/ Examination of product 3.2 1, 7 1, 8 1, 7 1, 5 1, 5 1, 3 1, 4 Contact resistance, dry circuit 3.2 3, 5 2, 4 2, 4 Insulation resistance 3.4 2, 6 Dielectric withstanding voltage 3.5 3, 7 Electrical stability 2/ 3.6 6 Capacitance 3.7 2 Solderability 3.8 2 Vibration 3.9 2 Physical shock 3.10 3

37、 Resistance to soldering heat 3/ 3.11 5 Terminal strength, pull test 3.12 3 Terminal strength, bend test 3.13 4 Durability 3.14 4 Actuation force 3.15 2, 6 Thermal shock 3.16 4 Humidity-temperature cycling 3.17 5 Temperature life 3.18 3 Mixed flow gas 3.19 3 1/ Numbers indicate sequence in which tes

38、t shall be performed for each sample. 2/ Test only 1 switch. 3/ Reserve only 1 switch for electrical stability test. 4.2.4 Certificate of compliance. A certificate of compliance for group B inspection requirements is acceptable, instead of performing group B inspection. 5. PACKAGING 5.1 Packaging. F

39、or acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements.

40、 Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packag

41、ing files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09003 REV A PAGE 7 6. NOTES (This sect

42、ion contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Switches conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not

43、available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing be

44、comes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance i

45、nspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Part Number Cross Reference MIL-PRF-83504 DSCC 09003 Tyco 1/ M83504/1-022 09003-022 2-435640-9 M83504/

46、1-023 09003-023 3-435640-0 M83504/1-024 09003-024 435640-2 M83504/1-025 09003-025 435640-3 M83504/1-026 09003-026 435640-4 M83504/1-027 09003-027 435640-1 M83504/1-028 09003-028 435640-5 M83504/1-029 09003-029 435640-6 M83504/1-030 09003-030 435640-7 M83504/1-031 09003-031 M83504/1-032 09003-032 3-4

47、35640-2 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime fro

48、m a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBU