DLA DSCC-DWG-09008-2009 RESISTOR FIXED WIREWOUND (ACCURATE) RADIAL LEADED 0 1 WATT (RBR81).pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Andrew R. Ernst DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 20 October 2009 CHECKED BY Andrew R. Ernst T

2、ITLE RESISTOR, FIXED, WIREWOUND, (ACCURATE), RADIAL LEADED, 0.1 WATT (RBR81) APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09008 REV PAGE 1 OF 7 AMSC N/A 5905-E706 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY C

3、ENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a fixed, wirewound (accurate), radial leaded, 0.1 watt resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following exa

4、mple: 09008- L 12601 F | | | | | | | | Drawing number Terminal (see 3.3.1) Resistance (see 3.3.2) Tolerance (see 3.3.3) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this documen

5、t to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39005 - Resistors, Fixed, Wirewound (Accurate), Nonestablished Reliability, and Established Reliability, General S

6、pecification for. MIL-PRF-39005/11 - Resistors, Fixed, Wirewound (Accurate), Nonestablished Reliability, and Established Reliability, Style RBR80 and RBR81. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-690 - Failure Rate Sampling P

7、lans and Procedures. MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardizatio

8、n Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this doc

9、ument takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-39005, and as specified herein. 3.2 Interfa

10、ce and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-39005/11 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE

11、A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 3 A, Max B, 0.005 (0.13) 0.500 (12.70) 0.400 (10.16) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parenthesis. 3. The lead measurements shall be made at the point of emergence from the body. 4. Leads are to be clean and solderable to

12、within 0.005 (0.13mm) from the resistor body. 5. Resistance measurement points for all values of resistance shall be .375 .0625 (9.53 mm 1.588 mm) from the end of the body. FIGURE 1. Radial leaded resistor. 3.3 Electrical characteristics. 3.3.1 Terminal. The terminal is identified by a single letter

13、 in accordance with table I. TABLE I. Terminal. Symbol Terminal L U Solderable Weldable Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 4 3.3.2 Resistan

14、ce. The nominal resistance is expressed in ohms and is identified by five digits; the first four digits represent significant figures and the last digit specifies the number of zeros to follow. When the values of resistance are less than 1,000 ohms, or when fractional values of an ohm are required,

15、the letter “R“ is substituted for one of the significant digits to represent the decimal point. When the letter “R“ is used, succeeding digits of the group represent significant figures. The resistance value designations are in accordance with MIL-PRF-39005. Minimum and maximum resistance values are

16、 as specified in table II. The standard values for every decade are in accordance with the “10 to 100” decade table of MIL-PRF-39005. The resistance values for 0.01 percent (T), 0.02 percent (Q), 0.05 percent (A) and 0.1 percent (B) resistance tolerances may be of any value, but it is preferred that

17、 the values are chosen within the “10 to 100” decade table of MIL-PRF-39005. 3.3.3 Resistance tolerance. Resistors are available in resistance tolerances in accordance with table II. TABLE II. Resistance and resistance tolerance. Resistance tolerance Minimum resistance Maximum resistance T (0.01 per

18、cent) Q (0.02 percent) A (0.05 percent) B (0.10percent) F (1.00 percent) 1 kilohms 100 ohms 100 ohms 10 ohms 10 ohms 200 kilohms 3.3.4 Resistance temperature characteristic. The resistance temperature characteristic shall not exceed the value listed in table III. TABLE III. Maximum resistance temper

19、ature characteristic. Resistance (ohms) Parts/million/C (ppm) Less than 100 ohms 100 ohms and above 10 5 3.3.5 Power rating. The power rating for all characteristics shall be 0.1 watt. Resistors power rating is based on continuous full load operation at an ambient temperature of +125C. For temperatu

20、re in excess of +125C, the load shall be derated in accordance with figure 1. 3.3.6 Voltage rating. The maximum continuous working voltage shall not exceed 100 volts. 3.3.7 Maximum weight. The maximum weight shall be 0.55 grams. 3.3.8 Maximum allowable reactance (see 4.5). The maximum allowable reac

21、tance shall be defined as follows: a. For resistance values less than 500 ohms, the phase angle shall not exceed +5 degrees. b. For resistance values 500 ohms or greater, but less than 20,000, the phase angle shall not exceed 10 degrees. c. For resistance values 20,000 ohms or greater, but less than

22、 50,000 ohms, the effective parallel capacitance shall not exceed 4.0 F. d. For resistance values of 50,000 ohms or greater, the maximum effective parallel capacitance shall not exceed 6.0 F. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SU

23、PPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 5 3.3.9 High Temperature exposure (see 4.6). The maximum allowable change in resistance after exposure to an ambient of 145C shall be as follows: a. For resistance values less of 10 ohms or greater, but less than

24、 100 ohms, the change in resistance shall not exceed phase angle shall not exceed 0.1 percent. b. For resistance values of 100 ohms or greater, the change in resistance shall not exceed 0.05 percent. FIGURE 1. Derating curve for high ambient temperatures. 3.4 Marking. Resistors shall be marked with

25、the PIN assigned herein (see 1.2) and manufacturers identification code (CAGE or logo), date code, and lot code. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent

26、, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceed

27、s the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-39005 Qualified Products List for at least one part, or perf

28、orm the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DSCC-VA. 3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a approved source of supply. 3.8 Workmanship. Resistors shall be unifor

29、m in quality and free from defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 6 4. VERIFICATI

30、ONS 4.1 Product assurance program. The product assurance program specified in MIL-PRF-39005 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Product level qualification. The product level qualification specified in MIL-PRF-39005 and MIL-STD-690 is not applicable

31、to this document. 4.3 Conformance provisions. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection and group B inspection of MIL-PRF-39005. 4.3.2 Group A inspection. Group A inspection shall be in accordance with MIL-PRF-39005. 4.3.3 Group

32、B inspection. Group B inspection shall be in accordance with MIL-PRF-39005 with an additional 30 samples to be performed on the maximum allowable reactance (see 3.3.8 and 4.5) and high temperature exposure tests (3.3.9 and 4.6) as described herein, with zero defectives allowed. 4.3.3.1 Certification

33、4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-39005. . The acquiring activity, at its discretion, may accept a certific

34、ate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.5 Maximum allowable reactance. The inherent reactance shall be measured as follows: a. Test instrument: Hewlett-Packard RX meter, model 250B; Tektronic LC meter, type 130, or any other equivalent meter. b.

35、Frequency range: 100 kHz to 500 kHz. 4.6 High temperature exposure. The high temperature exposure test shall be in accordance with MIL-PRF-39005. 5. PACKAGING 5.1 Packaging6. NOTES . For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When p

36、ackaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Depart

37、ment or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. (This section contains information

38、 of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistors are intended for use in dc amplifiers, voltmeter multipliers, electronic computers, meters, and laboratory test equipment. Provided by IHSNot for ResaleNo reproduction or networking permitted

39、without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09008 REV PAGE 7 6.2 Ordering data. The contract or purchase order will specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspecti

40、on data that parts have passed conformance inspection, with each shipment of parts by the manufacturer. c. Packaging requirements (see 5.1). d. Whether the manufacturer performs the group B inspection or provides a certificate of compliance (see 4.3.3.1). 6.3 Tin whisker growth6.4 . The use of alloy

41、s with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied ove

42、r top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Supplemen

43、tary insulation6.5 . Where potential to ground is over 250 volts, supplementary insulation should be provided. Low tolerance resistors6.6 . Low tolerance resistors (.005 and .01), exhibiting resistance shifts due to high humidity are normal to precision, fixed resistors. Before being considered out

44、of tolerance, resistors should be conditioned in a dry oven. Users of said resistors should contact suppliers for temperature and drying times. Resistors which continue to be out of tolerance after the above conditioning process should be considered rejects. User of record. Coordination of this docu

45、ment for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by

46、 telephone (614) 692-0552 or DSN 850-0552. 6.7 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.milor contact DSCC-VAT, Post Office Box 3990, C

47、olumbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 09008-* Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address Terminal: L and U Tolerance and Resistance: T - 1 kilohm to 200 kilohms Q and A - 100 ohms to 200 kilohms B and F 10 ohms to 200 kilohms HR340 54294 IRC Shallcross, Inc. U.S. 70 East Smithfield, NC 27577 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-