DLA DSCC-DWG-09011-2009 RESISTOR NETWORK FIXED FILM PRECISION 8 PAD BALL GRID ARRAY.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Jesus V. Garcia III DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 Original date of drawing 17 December 2009 CHECKED B

2、Y Andrew R. Ernst TITLE RESISTOR NETWORK, FIXED FILM, PRECISION 8 PAD, BALL GRID ARRAY APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09011 REV PAGE 1 OF 9 AMSC N/A 5905-E708 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENS

3、E SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a precision fixed, film, resistor network with 8 pad ball grid array. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 09

4、011 - * * * Drawing number Resistance value designator (see 3.3.1) Resistance tolerance (see 3.3.3) Schematic (see 3.3.8) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications, standards and handbooks form a part of this document to the ex

5、tent specified herein. Unless otherwise specified, the issues of these documents are those listed in the cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level

6、, General Specification for. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the eve

7、nt of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The indi

8、vidual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342 and herein (see figure 1). 3.3 Electrical characteristics 3.3.1 Resistance. T

9、he four-digit resistance designation is applicable to all resistance tolerances. The nominal resistance is identified by four digits; the first three digits represent significant figures and the last digit specifies the number of zeros to follow. When the value of resistance is less than 100 ohms, o

10、r when a fractional value of an ohm is required, the “R” will be substituted for one of the significant digits to represent the decimal point. When the letter “R” is used, succeeding digits of the group represent significant figures. The resistance values designations are shown in table I. Standard

11、values for every decade will follow the sequence demonstrated for “10 to 100” decade in table II. Resistance values not listed in table II for the appropriate resistance tolerance will be considered as not conforming to the specification. Provided by IHSNot for ResaleNo reproduction or networking pe

12、rmitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 3 Inch mm Inch mm Inch mm Inch mm Inch mm 0.002 0.051 0.005 0.127 0.025 0.635 0.050 1.270 0.200 5.080 0.003 0.076 0.010 0.254 0.030 0.762 0.058 1.473 0.250 6.350 NOT

13、ES: 1. Dimensions are in Inches. Metric equivalents are given for general information only. 2. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functio

14、nal aspects of the device, are acceptable. 3. The bottom view shown above represents the mounting side. FIGURE 1. Resistor network. TABLE I. Designation of resistance values for resistance Designation Resistance ohms 10R0 to 98R8 incl. 10.0 to 98.8 incl. 1000 to 9880 incl. 100 to 988 Incl. 1001 to 9

15、881 incl. 1,000 to 9,880 incl. 1002 to 9882 incl. 10,000 to 98,800 1003 incl. 100,000 incl. 0.030“ 0.00210/90 Sn/Pb SOLDER BALLSAE*0.025“ 0.010 0.050“ 0.0100.200“ 0.010(VIEW FROM TOP) (VIEW FROM BOTTOM)1 2 N 99.6 %AluminaSubstrate0.058“ 0.0050.250“ 0.003 A1 L 0.025“ 0.0030.200 + 0.003 Provided by IH

16、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 4 TABLE II. Standard resistance values for the 10 to 100 decade. 1/ (B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J)

17、(B), (C) (D) (F) (G) (J) (B), (C) (D) (F) (G) (J) 10.00 10.00 10.00 18.40 33.20 33.20 58.30 10.10 18.70 18.70 33.60 59.00 59.00 10.20 10.20 18.90 34.00 34.00 59.70 10.40 19.10 19.10 34.40 60.40 60.40 10.50 10.50 19.30 34.80 34.80 61.20 10.60 19.60 19.60 35.20 61.90 61.90 10.70 10.70 19.80 35.70 35.7

18、0 62.00 10.90 20.00 20.00 20.00 36.00 62.60 11.00 11.00 20.30 36.10 63.40 63.40 11.10 20.50 20.50 36.50 36.50 64.20 11.30 11.30 11.00 20.80 37.00 64.90 64.90 11.40 21.00 21.00 37.40 37.40 65.70 11.50 11.50 21.30 37.90 66.50 66.50 11.70 21.50 21.50 38.30 38.30 67.30 11.80 11.80 21.80 38.80 68.0012.00

19、 12.00 22.00 39.00 68.10 68.10 12.10 12.10 22.10 22.10 39.20 39.20 69.00 12.30 22.30 39.70 69.80 69.80 12.40 12.40 22.60 22.60 40.20 40.20 70.60 12.60 22.90 40.70 71.50 71.50 12.70 12.70 23.20 23.20 41.20 41.20 72.30 12.90 23.40 41.70 73.20 73.20 13.00 13.00 13.00 23.70 23.70 42.20 42.20 74.10 13.20

20、 24.00 24.00 42.70 75.00 75.00 75.00 13.30 13.30 24.30 24.30 43.00 75.90 13.50 24.60 43.20 43.20 76.80 76.80 13.70 13.70 24.90 24.90 43.70 77.70 13.80 25.20 44.20 44.20 78.70 78.70 14.00 14.00 25.50 25.50 44.80 79.60 14.20 25.80 45.30 45.30 80.60 80.60 14.30 14.30 26.10 26.10 45.90 81.60 14.50 26.40

21、 46.40 46.40 82.0014.70 14.70 26.70 26.70 47.00 47.00 82.50 82.50 14.90 27.00 47.50 47.50 83.50 15.00 15.00 15.00 27.10 48.10 84.50 84.50 15.20 27.40 27.40 48.70 48.70 85.60 15.40 15.40 27.70 49.30 86.60 86.60 15.60 28.00 28.00 49.90 49.90 88.70 88.7015.80 15.80 28.40 50.50 89.80 16.00 16.00 28.70 2

22、8.70 51.00 90.90 90.90 16.20 16.20 29.10 51.10 51.10 91.0016.40 29.40 29.40 51.70 92.00 93.10 16.50 16.50 29.80 52.30 52.30 93.10 16.70 30.00 53.00 94.20 95.30 16.90 16.90 30.10 30.10 53.60 53.60 95.30 17.20 30.50 54.20 96.50 97.60 17.40 17.40 30.90 30.90 54.90 54.90 97.60 17.60 31.20 55.60 98.8017.

23、80 17.80 31.60 31.60 56.00 18.00 18.00 32.00 56.20 56.20 18.20 18.20 32.40 32.40 56.9032.80 57.60 57.60 33.00 1/ Resistance values not listed in table II for the appropriate resistance tolerance will be considered as not conforming to the specification. The resistance values for tolerances B, C, and

24、 D may be any value within the limits specified in 3.3.2, but it is preferred that values be chosen from “B”, “C” and “D” column of table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE I

25、DENT NO. 037Z3 DWG NO. 09011 REV PAGE 5 3.3.2 Resistance range and resistance temperature characteristic. The resistance range shall be from 10 ohms to 100 kilohms. The corresponding resistance temperature characteristic is specified in table III. TABLE III. Resistance range and resistance temperatu

26、re characteristic. Resistance range (in ohms) Resistance Temperature Characteristic (RTC) in ppm/OC 10 to 25 100 25.1 to 50 50 50.1 to 200 25 201 to 100K 25 3.3.3 Resistance tolerance. Resistors are available in resistance tolerances as specified in table IV. TABLE IV. Resistance tolerance. Symbol R

27、esistance tolerance percent Available resistance range (in ohms) B 0.1 50.1 to 100K C 0.25 10 to 100K D 0.5 F 1.0 G 2.0 J 5.0 3.3.4 Resistor power rating. The resistor power rating for individual resistors shall be 100 milliwatts (.1 Watt) maximum at 70OC derated to zero watts at 150OC. 3.3.5 Packag

28、e power rating. The package power rating shall be 400 milliwatts (0.4 Watt) maximum at 70OC derated to zero watts at 150OC (see figure 2). FIGURE 2. Derating curve. Percent of rated power-65 -50 -25 0 25 50 75 100 125 150 175 Temperature (OC) 100 80 60 40 20 0 70OC -55OC Provided by IHSNot for Resal

29、eNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 6 3.3.6 Maximum Voltage. The maximum voltage of the network shall not exceed 50 volts 3.3.7 Noise. The noise rating for the network

30、shall be less than () -25 decibels. 3.3.8 Schematic. The schematics of the resistor network are identified by a single letter in accordance with figure 3. Schematic A FIGURE 3. Schematic. 3.3.9 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externa

31、lly. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.4 Thermal shock. When networks are tested as specified in MIL-PRF-55342, for thermal shock the change in resistance shall not exceed 0.

32、1 percent 0.01 ohm. 3.5 Low temperature operation. When networks are tested as specified in MIL-PRF-55342, for low temperature operation the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.6 Short time overload. When networks are tested as specified in MIL-PRF-55342, for short time ov

33、erload the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.7 High temperature exposure. When networks are tested as specified in MIL-PRF-55342, for high temperature exposure the change in resistance shall not exceed 0.1 percent 0.01 ohm. 3.8 Resistance to soldering heat. When networks

34、 are tested as specified in MIL-PRF-55342, for resistance to soldering heat the change in resistance shall not exceed 0.05 percent 0.01 ohm. 3.9 Moisture resistance. When networks are tested as specified in MIL-PRF-55342, for moisture resistance the change in resistance shall not exceed 0.1 percent

35、0.01 ohm. 3.10 Resistance temperature characteristic. When networks are tested as specified in MIL-PRF-55342, the RTC shall not exceed the values specified (see 3.3.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS C

36、OLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 7 3.11 Marking. Marking is not required on this resistor; however, each waffle pack and each unit package shall be marked with the PIN assigned herein (see 1.2), the manufacturers identification code, the date code, and the lot code. A

37、t the option of the manufacturer, the resistor may be marked (i.e., laser, color dot, etc.). The marking shall remain legible after all tests. 3.12 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF-55342 Qualified Produ

38、cts List for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.12.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as approved sou

39、rces of supply. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economic

40、ally advantageous life cycle costs. 3.14 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and be free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL

41、-PRF-55342 is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and B inspections of MIL-PRF-55342. 4.2.1.1 Group A inspection. Group A inspection shall be in accordance with MIL-PRF-

42、55342 with the following exceptions. 4.2.1.1.1 Visual Inspection. The visual inspection of Subgroup 1 is not required. 4.2.1.1.2 Solderability. The method for solderability test for Subgroup 4 shall be conducted per manufacturers standard practice. All terminations shall exhibit a continuous solder

43、coating free from defects for a minimum of 95 percent of the critical surface area of any individual termination. Anomalies other than dewetting, non-wetting, and pinholes are not cause for rejection. 4.2.1.2 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-55342. 4.2.1.2.1

44、 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purpose, the packaging requirements shall be as specified in the contract or order (

45、see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within t

46、he Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot

47、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09011 REV PAGE 8 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.

48、) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery; One copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipm