DLA DSCC-DWG-09020 REV A-2012 CAPACITORS FIXED GLASS DIELECTRIC (AXIAL WIRE-LEAD TERMINALS).pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added a 10% tolerance option. 14 March 2012 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV A A A A A A PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DLA LAND AND MARITIME

2、COLUMBUS, OH 43218-3990 Original date of drawing 31 January 2012 CHECKED BY William E. Sindelar TITLE CAPACITORS, FIXED, GLASS DIELECTRIC, (AXIAL WIRE-LEAD TERMINALS) APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 09020 SCALE N/A REV A PAGE 1 OF 6 AMSC N/A 5910-2012-E06Provided

3、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09020 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for glass dielectric capacitors screened to MIL-PRF-23269.

4、1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 09020 -001 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents c

5、ited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this

6、specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are t

7、hose cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-23269 - Capacitors, Fixed, Glass Dielectric, Established Reliability, General Specification for. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch or from the Standardizat

8、ion Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), t

9、he text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-23269

10、and herein (see figure 1 and table I). 3.1.1 Case material. Glass. 3.1.2 Terminals. Solderable. 3.1.3 Seal. Hermetic. 3.1.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97

11、 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO

12、. 09020 REV A PAGE 3 Inches mm Inches mm .001 0.03 .078 1.98 .004 0.10 .141 3.58 .025 0.64 .750 19.05 .031 0.79 .766 19.46 .047 1.19 1.125 28.58 .062 1.57 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. See marking requirement. FIGURE 1. Dimension

13、s and configurations. 3.3 Electrical characteristics. 3.3.1 Capacitance tolerance. See table I. 3.3.2 Rated voltage. See table I. 3.3.3 Capacitance. When measured as specified in MIL-PRF-23269, the capacitance shall be within the applicable tolerance of the nominal value specified in table I. 3.3.4

14、Dissipation factor. When measured as specified in MIL-PRF-23269, the dissipation factor shall not exceed 0.1 percent. 3.3.5 Temperature coefficient and capacitance drift (manufacturer eligibility only (see 3.9). When measured as specified in MIL-PRF-23269, the capacitors shall meet the following req

15、uirements: a. Temperature coefficient: 140 parts per million (ppm)/C 25 ppm/C. b. Capacitance drift: 0.1 percent or 0.1 pF, whichever is greater. 09020 -001 TM 09A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO S

16、IZE A CODE IDENT NO. 037Z3 DWG NO. 09020 REV A PAGE 4 3.3.6 Insulation resistance (IR). When measured as specified in MIL-PRF-23269, the insulation resistance shall be 100,000 megaohms, minimum, at +25C. 3.3.7 Quality factor (Q) (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23

17、269. 3.4 Seal. In accordance with MIL-PRF-23269, test I. 3.5 Thermal shock (manufacturer eligibility group C only (see 3.9). In accordance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.1 percent maximum. 3.6 Moisture resistance (manufacturer eligibility only (see 3.9).

18、In accordance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.1 percent maximum. 3.7 Life (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. The following details shall apply: a. Capacitance (240 hours and 2,000 hours): 0.5 percent maximum. b. Dis

19、sipation factor (240 hours and 2,000 hours): 0.15 percent maximum. 3.8 Marking. In accordance with MIL-PRF-23269, except the capacitor shall be marked with the PIN as specified herein (see 1.2). 09020 DLA Land and Maritme drawing number -001 Non-significant dash number TM 09A | Trademark Year Sequen

20、tial 4 week lot code code 3.9 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-23269 Qualified Products Database for at least one part, or perform the group A and group C inspections specified herein on a sample of pa

21、rts agreed upon by the manufacturer and DLA Land and Maritime - VAT. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operation

22、al and maintenance requirements, and promotes economically advantageous life cycle costs. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.12 Workmanship. The capacitor shall be uniform in quality and fr

23、ee from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A insp

24、ection of MIL-PRF-23269. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible p

25、ackaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Mi

26、litary Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DW

27、G NO. 09020 REV A PAGE 5 TABLE I. Electrical characteristics and dash numbers. Capacitance (nF) Capacitance tolerance DLA Land and Maritime Drawing PIN 09020- 500 V dc 100 V dc 3.6 1% 001 101 3.6 2% 002 102 3.6 5% 003 103 3.6 10% 037 137 3.9 1% 004 104 3.9 2% 005 105 3.9 5% 006 106 3.9 10% 038 138 4

28、.3 1% 007 107 4.3 2% 008 108 4.3 5% 009 109 4.3 10% 039 139 4.7 1% 010 110 4.7 2% 011 111 4.7 5% 012 112 4.7 10% 040 140 5.1 1% 013 113 5.1 2% 014 114 5.1 5% 015 115 5.1 10% 041 141 5.6 1% 016 116 5.6 2% 017 117 5.6 5% 018 118 5.6 10% 042 142 6.2 1% 019 119 6.2 2% 020 120 6.2 5% 021 121 6.2 10% 043

29、143 300Vdc 100 V dc 6.8 1% 022 122 6.8 2% 023 123 6.8 5% 024 124 6.8 10% 044 144 7.5 1% 025 125 7.5 2% 026 126 7.5 5% 027 127 7.5 10% 045 145 8.2 1% 028 128 8.2 2% 029 129 8.2 5% 030 130 8.2 10% 046 146 9.1 1% 031 131 9.1 2% 032 132 9.1 5% 033 133 9.1 10% 047 147 10.0 1% 034 134 10.0 2% 035 135 10.0

30、 5% 036 136 10.0 10% 048 148 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 09020 REV A PAGE 6 6. NOTES (This section contains information of a general or explanatory nature wh

31、ich may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exc

32、lusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ord

33、ering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer.

34、c. Requirements for notification of change of product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whisk

35、ers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have

36、shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared spec

37、ification or drawing. 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these no

38、tations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. 6.6 Users of record. Coordination of this document for future revisions is coordinated only wit

39、h the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to capacitorfilterdla.mil, or by telephone (614) 692-4

40、709 or DSN 850-4709. 6.7 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email t

41、o capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 16299 AVX Corporation FM30*079192 3900 Electronics Drive Raleigh, NC 27604-1698 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-