DLA DSCC-DWG-10005-2010 RESISTOR PRECISION CURRENT SENSOR 100 WATTS.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Andrew R. Ernst DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 9 March 2010 CHECKED BY Andrew R. Ernst TITLE

2、RESISTOR, PRECISION CURRENT SENSOR, 100 WATTS APPROVED BY Michael Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 10005 REV PAGE 1 OF 6 AMSC N/A 5905-E727 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZ

3、E A CODE IDENT NO. 037Z3 DWG NO. 10005 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for 100 watts, precision current sensor resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 10005 - * * I I I I I I Drawing Number Resistance (3.3.1) Resistance t

4、olerance (3.3.2) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While ev

5、ery effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handboo

6、ks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fix

7、ed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Sta

8、ndardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text

9、of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-55342 and as specified herein. 3

10、.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified herein (see figure 1). 3.3 Electrical characteristics. 3.3.1 Resistance. The nominal resistance expressed in ohms is identified by five digits; an “R” shall be used to represent the decim

11、al point. The resistance value designations are shown in table I. Appropriate values not listed in the “10 to 100” decade table of MIL-PRF-55342 for the appropriate resistance tolerance shall be considered as not conforming to the specification. Provided by IHSNot for ResaleNo reproduction or networ

12、king permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10005 REV PAGE 3 Ltr Inches mm Min Max Min Max A 1.497 1.505 38.02 38.23 B 1.221 1.249 31.01 31.72 D .307 .323 7.80 8.20 E (ref) .161 .169 4.09 4.29 F .587 .595 14.91 15.11

13、G 1.186 1.194 30.12 30.33 H .161 .169 4.09 4.29 J .465 .481 11.81 12.22 K (ref) .351 .359 8.92 9.12 L (ref) .077 .081 1.96 2.06 M .959 1.001 24.36 25.41 N .209 max 5.30 max P .496 .504 12.60 12.80 R (ref) .030 .034 0.76 0.86 T .158 min 4.00 min NOTES: 1. Dimensions are in inches. 2. Millimeters are

14、given for information only. FIGURE 1. Current sense resistor. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10005 REV PAGE 4 3.3.1 Resistance range. The resistance r

15、ange shall be from 0.0005 ohms to 1.0000 ohms. Nominal resistance values are as specified in table I. TABLE I. Resistance value designations. Designation Resistance ohms R0005 to R0009 inclusive R0010 to R0097 inclusive R0100 to R0976 inclusive R1000 to R9760 inclusive 1R000 inclusive 0.0005 to 0.00

16、09 inclusive 0.0010 to 0.0097 inclusive 0.0100 to 0.0976 inclusive 0.1000 to 0.9760 inclusive 1.000 3.3.2 Resistance tolerance. The resistance tolerance shall be (F) 1 percent. 3.3.3 Power rating. The power rating shall be 100 watts at +70C back plate temperature. For operation at temperatures highe

17、r than +70C, derate in accordance with figure 2. 3.3.4 Temperature range. The temperature range shall be -55C to +155C. 3.3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 9

18、7 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.3.6 Temperature coefficient. For temperatures between -15C to 105C, the temperature coefficient shall be as 60 ppm/C. For resistance values between 0.0270 and 0.0490 the temperature coefficient shall be 5

19、00 ppm/C. 3.3.7 Dielectric strength. The maximum continuous working voltage shall be 1,000 volts dc. 3.3.8 Pulse current. The pulse current shall be up to 500A/0.5 sec (dependent on resistance value). Contact manufacturer for additional information (see 6.5). FIGURE 2. Derating curve. Provided by IH

20、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10005 REV PAGE 5 3.4 Marking. Resistors shall be marked with the PIN assigned herein (see 1.2), and manufacturers CAGE code (or logo)

21、, in accordance with MIL-STD-1285. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, an

22、d promotes economically advantageous life cycle costs. 3.6 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DSCC-VA. 3.6.1 Certificat

23、e of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply (see 6.2d). 3.7 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1

24、 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A (ER level inspection; Subgroup 4 not applicable) and group B (Subgroup 1; short ti

25、me overload not applicable) inspection of MIL-PRF-55342. 4.2.2 Certification. The acquiring activity may accept a certificate of compliance in lieu of group B inspection (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-55342. 5. PACKAGING 5.1 Packa

26、ging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requir

27、ements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated

28、 packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military

29、 specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application, described herein are intended to be used in surface mount applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Co

30、mplete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer perform

31、s the group B tests or provides certification of compliance with group B requirements. If purchase order makes no reference to group B screening the manufacturer will provide a certification of compliance (see 3.6.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

32、se from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10005 REV PAGE 6 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime f

33、rom a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the gr

34、owth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of

35、this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.5 Approved source of supply. Approved source of supply is liste

36、d herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN Vendors similar des

37、ignation or type number 1/ Vendor CAGE Vendors name and address 10005-* TGHG 44655 Ohmite Mfg. Company 1600 Gulf Roa, Suite 850 Rolling Meadows, IL 60008 Plant: Victoreen de Mexico, S.A. de C. V. Oriente 2, #46 Cd. Inductrial Apdo. Postal 171 Matamoros, Tam. 87499 Mexico 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-