DLA DSCC-DWG-10006-2010 RESISTOR CURRENT SENSE OPEN AIR STANDARD LEADS 1 WATT.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Andrew R. Ernst DESIGN ACTIVITY: DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 15 October 2010 CHECKED BY A

2、ndrew R. Ernst TITLE RESISTOR, CURRENT SENSE, OPEN AIR, STANDARD LEADS, 1 WATT APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 10006 REV PAGE 1 OF 6 AMSC N/A 5905-E728 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND M

3、ARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10006 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an open air, current sense, 1 watt resistor with standard leads. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 10

4、006- R0500 F | | | | | | Drawing number Resistance (see 3.3.1) Tolerance (see 3.3.2) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specificatio

5、n or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.

6、2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPAR

7、TMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39007 - Resistors, Fixed, Wire Wound (Power Type), Nonestablished Reliability, Established Reliability and Space Level, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Establish

8、ed Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue,

9、Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersede

10、s applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-39007, and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface an

11、d physical dimensions as specified in herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10006 REV PAGE 3 NOTES: 1. Dimensions are in inches. 2. Millimeter e

12、quivalents are given for general information only. Ltr Dimensions (Inches and (mm) A .450 +.040/-.020 (11.43 +1.020/-0.508) B 0.27 typical (6.86) C .125 .030 (3.18 0.762) E .065 +.010/-.005 (1.65 +0.254/-0.127) F .040 .002 (1.02 0.051) FIGURE 1. Open air, current sense resistor. 3.3 Electrical chara

13、cteristics. 3.3.1 Resistance. The nominal resistance is expressed in ohms and is identified by five digits; the letter “R“ shall be used to represent the decimal point. The resistance value designations are shown in table I. 3.3.2 Resistance range. The resistance range shall be from 0.005 ohm to 0.1

14、00 ohm. TABLE I. Resistance value designations. Designation Resistance ohms R0050 to R0097 inclusive R0100 to R0970 inclusive R1000 inclusive 0.0050 to 0.0097 inclusive 0.0100 to 0.0970 inclusive 0.1000 inclusive 3.3.2 Resistance tolerance. Resistors are available in resistance tolerances of (F) 1 p

15、ercent; (G) 2 percent; and (J) 5 percent. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10006 REV PAGE 4 3.3.3 Resistance temperature characteristic. The resistance temperatur

16、e characteristic of the alloy shall not exceed 20 ppm. Note: The resistance temperature characteristic is based on the metal alloy and copper termination and will vary slightly due to mounting methods and resistance range of the product. Values depicted are calculated and are less than the values in

17、dicated. 3.3.4 Power rating. The power rating shall be 1 watt at 85C. For temperatures in excess of +85C shall be derated in accordance with figure 2. 3.3.5 Inductance. Resistors shall have an inductance of less the 10 nanohenries. 3.3.6 Operating temperature. Resistors shall have an operating tempe

18、rature of -40C to +125C. FIGURE 2. Derating curve for high ambient temperatures. 3.4 Marking. Resistors shall be marked with the resistance value only due to size limitations. Each unit package shall be marked with PIN assigned herein (see 1.2) and manufacturers identification code (CAGE or logo), d

19、ate code, and lot code. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6

20、Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous li

21、fe cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10006 REV PAGE 5 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manu

22、facturer shall be listed on the MIL-PRF-39007 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.7.1 Certificate of compliance. A certificate of compliance shall be

23、 required from manufacturers requesting to be an approved source of supply. 3.8 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATIONS 4.1 Product assurance program. The product assurance program specified in MI

24、L-PRF-39007 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Product level qualification. The product level qualification specified in MIL-PRF-39007 and MIL-STD-690 is not applicable to this document. 4.3 Conformance provisions. 4.3.1 Inspection of product for de

25、livery. Inspection of product for delivery shall consist of group A inspection (ER inspection only) and group B inspection of MIL-PRF-39007. 4.3.2 Group A inspection. Group A inspection (ER inspection only) shall be in accordance with MIL-PRF-39007 (Subgroup 1 shall consist of DC resistance only, th

26、is testing is completed through machine automation. Test data can be supplied on sampling bases in accordance with table XIII (subgroup 2) of MIL-PRF-39007 (see 6.2.d). 4.3.3 Group B inspection. Group B inspection shall be in accordance with MIL-PRF-39007. 4.3.3.1 Certification. The acquiring activi

27、ty, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2e). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materie

28、l is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Age

29、ncy, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a gene

30、ral or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistors are intended for use in dc amplifiers, voltmeter multipliers, electronic computers, meters, and laboratory test equipment. Provided by IHSNot for ResaleNo reproduction or networking permitted without li

31、cense from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10006 REV PAGE 6 6.2 Ordering data. The contract or purchase order will specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection data that parts h

32、ave passed conformance inspection, with each shipment of parts by the manufacturer. c. Bulk packaging requirements (see 5.1). d. Whether the manufacturer performs the group A, dc resistance sample test data (see 4.3.2). e. Whether the manufacturer performs the group B inspection or provides a certif

33、icate of compliance (see 4.3.3.1). 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating cond

34、itions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B5

35、45 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be ach

36、ieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.5 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become availa

37、ble. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ Vend

38、or CAGE Vendor name and address 10006-* OAR-1 11502 International Resistive Company, INC 736 Greenway Road Boone, NC 28607-4830 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-