DLA DSCC-DWG-10019 REV A-2013 CONNECTOR ELECTRICAL COAXIAL RADIO FREQUENCY SHROUD 2 HOLE PIN AND ADAPTER ELECTRICAL COAXIAL SOCKET CONTACT SERIES SMPM TO SMPM.pdf

1、 AMSC N/A 5935-E852-001 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed disengage force from 1.5 to 0.5. 04 September 2013 Abdonasser Abdouni REV PAGE REV STATUS OF PAGES REV A PAGE 1 2 3 4 5 6 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Jeremy Funk Original date o

2、f drawing 03 March 2013 CHECKED BY TITLE Jeremy Funk CONNECTOR, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SHROUD 2 HOLE PIN AND ADAPTER, ELECTRICAL, COAXIAL, SOCKET CONTACT, SERIES SMPM TO SMPM APPROVED BY Abdonasser Abdouni SIZE CAGE CODE DWG. NO. 10019 A 037Z3 REV A PAGE 1 OF 6 CURRENT DESIGN ACTIVITY

3、 CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 2 NOTES: 1. D

4、imensions are in inches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Special tools shall be required for assembly. Contact manufacturer. FIGURE 1. General configuration, adapter. inches mm .012 .305 .095 2.41

5、 .110 2.79 .210 5.33 Part or Identifying Number 10019-A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 3 Part or Identifying Number (PIN) Dimension

6、 A Dimension B Dimension C Dimension D Shroud design 10019-1 .282 .125 .073 .375 Full detent 10019-1b .282 .125 .073 .375 Smooth bore 10019-2 .481 .150 .103 .625 Full detent 10019-2b .481 .150 .103 .625 Smooth bore NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information o

7、nly. 3. All undimensioned pictorial configurations are for reference purposes only. 4. Special tools shall be required for assembly. Contact manufacturer. inches mm inches mm .001 .025 .120 3.05 .004 .102 .125 3.17 .005 .127 .130 3.30 .008 .203 .150 3.81 .028 .711 .282 7.16 .073 1.85 .375 9.52 .083

8、2.11 .481 12.22 .091 2.31 .625 15.87 .103 2.62 D DIA A B Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 4 FIGURE 2. General configuration, shroud.

9、ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: DC to 40 GHz. DC to 65 GHz. (10019-A only) RF leakage: -80 dB mated pair, typical. Voltage rating: 217 V rms maximum at sea level. 42 V rms at 70,000 feet. Operating temperature: -65C to +165C. REQUIREMENTS: (All electrical and mechanica

10、l requirements shall be maintained during radial misalignment. Requirements of drawing 84148 are applicable.) Dimensions and configurations: See figures 1and 2. Interface dimensions: In accordance with MIL-STD-348A. Force to engage: Full detent: 8 pounds maximum. Smooth bore: 4 pounds maximum. Force

11、 to disengage: 4.5 pounds minimum - full detent 0.5 pounds minimum - smooth bore. Center contact inspection conditions after heat treat Oversize test pin: Test pin diameter: .0135 inch +.0001/-.0000 inch. Insertion depth: .030 inch minimum, .045 inch maximum. Number of insertions: 3 Insertion force

12、test: Test pin diameter: .0130 inch +.0001/-.0000 inch. Insertion force: 12 ounces, maximum. Insertion depth: .030 inch minimum, .045 inch maximum. Withdrawal force test: Test pin diameter: .0110 +0000/-.0001 inch. Withdrawal force: 0.25 ounce, minimum. Insertion depth: .030 inch minimum, .045 inch

13、maximum. Radial misalignment: Total radial misalignment between centerlines of connector shroud or mating planes, .010 inch (0.25 mm), min (.020 min (0.51 mm), total). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS CO

14、LUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 5 Axial misalignment: .000/.010 (0.00/0.25 mm). Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Center contact retention: 1.5 pounds minimum axial force (Socket

15、 contact adapter only). Radial torque: Not applicable. Voltage standing wave ratio: DC to 18 gigahertz: 1.15:1 maximum. 18 to 40 gigahertz: 1.25:1 maximum. 40 to 65 gigahertz: 1.35:1 maximum -A only VSWR procedure. The VSWR shall be measured in accordance with the following procedure or a method acc

16、eptable to the Government. Part should be tested using a Network Analyzer with the Time Domain (TDR) option installed. This is essential to allow the effect of the adapters to be “gated” out. The recommended network analyzer systems include Hewlett Packard HP 8510. Wiltron 360 or equivalent. The pri

17、nter/plotter and the computer should be any unit compatible to the system. The device under test (DUT) shall consist of DSCC PIN 10019-A, PIN 10019-1, or PIN 10019-2 mated at both ends with adapters capable of performing to 40 GHz . Calibration of the system should be performed using the manufacture

18、rs calibration kits and the recommended calibration procedures. The frequency range shall be DC to 40 GHz. The VSWR calibration test setup shall be verified using the manufacturers verification kits. The calibrated system VSWR shall be less than 1.02 + .001F (F in GHZ). The VSWR of the DUT shall be

19、measured using the procedures described in the manufacturers operating instructions. The time domain shall then be used to remove the effects of the test adapter. The output shall be generated using the appropriate printer/plotter. Moisture resistance: MIL-STD-202, method 106, except step 7b shall b

20、e omitted. Resistance shall be 1,000 megohms within 5 minutes after removal from humidity (Socket contact adapter only). Contact resistance (in milliohms, maximum): Initial Center contact 6.0 Outer contact 2.0 Dielectric withstanding voltage at sea level: 325 V rms minimum 80 V rms at 70,000 feet (S

21、ocket contact adapter only). Vibration, high frequency: MIL-STD-202, method 204, test condition D. Vibration, random: MIL-STD-202, method 214, test condition F, duration 15 minutes, minimum. Corona level (Socket contact adapter only): Altitude: 70,000 feet. 125 V rms, minimum. Insulation resistance:

22、 5,000 megohms minimum when tested in accordance with MIL-PRF-39012 (Socket contact adapter only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 6

23、 Altitude: Sea level to 70,000 feet. Solderability: Not applicable. Shock (specified pulse): MIL-STD-202, method 213, test condition I (Socket contact adapter only). Thermal shock: MIL-STD-202, method 107, test condition B (except high temperature to be +165C). RF high potential withstanding voltage

24、: 200V rms minimum at sea level. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention: Not applicable. Coupling mechanism retention force: Not applicable. Durability: Full detent: 100 cycles. Smooth bore: 500 cycles. RF insertion loss: .12 Frequency (GHz) dB Part or Identifying Number

25、(PIN): 10019-X (“X” is a place holder). DSCC drawing PIN 1/ Description 10019-A SMPM to SMPM Adapter 2/ 10019-1 Shroud .282 inch ( 7.16mm ) 3/ - Full detent 10019-1b Shroud .282 inch ( 7.16mm ) 3/ - Smooth bore 10019-2 Shroud .481 inch (12.22mm ) 3/ - Full detent 10019-2b Shroud .481 inch (12.22mm )

26、 3/ - Smooth bore 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. 2/ See Figure 1 3/ See Figure 2 Materials: Contacts and adapter housing: Beryllium copper in accordance with ASTM B196/B196M, gold plated to a minimum thickness of 50 microinc

27、hes (1.27 m) in accordance with MIL-DTL-45204, type II, grade C, class 1, over 50 microinches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, class 1. Shroud : Stainless steel, passivated with 32 microinch finish on mating features. Approved sources. Approved sources of supply will be l

28、isted herein. Approved sources are required to be a QPL source on MIL-PRF-39012 or MIL-PRF-31031. Additional sources will be added as they become available. The vendors listed on the requirements drawing agree to this drawing and a certificate of compliance has been submitted to DLA Land and Maritim

29、e - VAI. Vendor CAGE Vendor Name and Number address 95077 SV Microwave, Inc. 2400 Centrepark West Drive Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 10019 REV PAGE 7 West Palm Beach, Florida 33409-6469 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-