DLA DSCC-DWG-13005-2012 CAPACITORS FIXED GLASS DIELECTRIC (AXIAL WIRE-LEAD TERMINALS).pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV OF PAGES PAGES PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 11 December 2012 CHECKED BY Mark Rush TIT

2、LE CAPACITORS, FIXED, GLASS DIELECTRIC, (AXIAL WIRE-LEAD TERMINALS) APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13005 SCALE N/A REV PAGE 1 OF 7 AMSC N/A 5910-2013-E02Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND

3、 MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13005 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for glass dielectric capacitors screened to MIL-PRF-23269. The capacitors described herein are possible replacements for MIL-PRF-23269/2 capacitors (see 6.4 and

4、 table II). 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 13005 -001 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include

5、 documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 an

6、d 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these doc

7、uments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-23269 - Capacitors, Fixed, Glass Dielectric, Established Reliability, General Specification for. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or from the Stand

8、ardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related specification she

9、ets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF

10、-23269 and herein (see figure 1). 3.1.1 Case material. Glass. 3.1.2 Terminals. Solderable. 3.1.3 Seal. Hermetic. 3.1.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 perc

11、ent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 130

12、05 REV A PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. See marking requirement (see 3.8). FIGURE 1. Dimensions and configurations. 3.3 Electrical characteristics. 3.3.1 Capacitance tolerance. See table I. 3.3.2 Rated voltage. See table I.

13、 3.3.3 Capacitance. When measured as specified in MIL-PRF-23269, the capacitance shall be within the applicable tolerance of the nominal value specified in table I. 3.3.4 Dissipation factor. When measured as specified in MIL-PRF-23269, the dissipation factor shall not exceed 0.1 percent. 3.3.5 Tempe

14、rature coefficient and capacitance drift (manufacturer eligibility only (see 3.9). When measured as specified in MIL-PRF-23269, the capacitors shall meet the following requirements: a. Temperature coefficient: 140 parts per million (ppm)/C 25 ppm/C. b. Capacitance drift: 0.1 percent or 0.1 pF, which

15、ever is greater. Inches mm Inches mm .001 0.03 .047 1.19 .004 0.10 .109 2.77 .016 0.41 .266 6.76 .020 0.51 .469 11.91 .031 0.79 1.125 28.58 13005 -001 TM 12A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A

16、CODE IDENT NO. 037Z3 DWG NO. 13005 REV A PAGE 4 3.3.6 Insulation resistance (IR). When measured as specified in MIL-PRF-23269, the insulation resistance shall be 100,000 megohms, minimum, at +25C. 3.3.7 Quality factor (Q) (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. 3.

17、4 Seal. In accordance with MIL-PRF-23269, test I. 3.5 Thermal shock (manufacturer eligibility group C only (see 3.9). In accordance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.1 percent maximum. 3.6 Moisture resistance (manufacturer eligibility only (see 3.9). In acco

18、rdance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.1 percent maximum. 3.7 Life (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. The following details shall apply: a. Capacitance (240 hours and 2,000 hours): 0.5 percent maximum. b. Dissipatio

19、n factor (240 hours and 2,000 hours): 0.15 percent maximum. 3.8 Marking. In accordance with MIL-PRF-23269, except the capacitor shall be marked with the PIN as specified herein (see 1.2. 13005 DLA Land and Maritime drawing number -001 Non-significant dash number TM 12A | Trademark Year Sequential 4

20、week lot code code 3.9 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-23269 Qualified Products Database for at least one part, or perform the group A and group C inspections specified herein on a sample of parts agr

21、eed upon by the manufacturer and DLA Land and Maritime-VA. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and mai

22、ntenance requirements, and promotes economically advantageous life cycle costs. 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.12 Workmanship. The capacitor shall be uniform in quality and free from an

23、y defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of

24、MIL-PRF-23269. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging a

25、ctivity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Dep

26、artments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 1300

27、5 REV A PAGE 5 TABLE I. Electrical characteristics. DLA Land and Maritime drawing (PIN) 13005- Capacitance (pF) Capacitance tolerance 500 Vdc 100 Vdc 001 101 220 1% 002 102 220 2% 003 103 220 5% 004 104 240 1% 005 105 240 2% 006 106 240 5% 007 107 270 1% 008 108 270 2% 009 109 270 5% 010 110 300 1%

28、011 111 300 2% 012 112 300 5% 013 113 330 1% 014 114 330 2% 015 115 330 5% 016 116 360 1% 017 117 360 2% 018 118 360 5% 019 119 390 1% 020 120 390 2% 021 121 390 5% 022 122 430 1% 023 123 430 2% 024 124 430 5% 025 125 470 1% 026 126 470 2% 027 127 470 5% 028 128 510 1% 029 129 510 2% 030 130 510 5%

29、300 Vdc 100 Vdc 031 131 560 1% 032 132 560 2% 033 133 560 5% 034 134 620 1% 035 135 620 2% 036 136 620 5% 037 137 680 1% 038 138 680 2% 039 139 680 5% 040 140 750 1% 041 141 750 2% 042 142 750 5% 043 143 820 1% 044 144 820 2% 045 145 820 5% 046 146 910 1% 047 147 910 2% 048 148 910 5% Provided by IH

30、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13005 REV A PAGE 6 TABLE I. Electrical characteristics. Continued. DLA Land and Maritime drawing (PIN) 13005- Capacitance (pF) Capacitance tole

31、rance 300 Vdc 100 Vdc 049 149 1,000 1% 050 150 1,000 2% 051 151 1,000 5% 052 152 1,100 1% 053 153 1,100 2% 054 154 1,100 5% 055 155 1,200 1% 056 156 1,200 2% 057 157 1,200 5% 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6

32、.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unn

33、ecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order s

34、hould specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change o

35、f product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years af

36、ter manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers.

37、 For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 MIL-PRF-23269/2 replacements. The capacitors described herein are possible replacements for MIL-PRF-23269/2 capacitors. Users are cautioned to evaluate this document for

38、their particular application before citing it as a replacement document. MIL-PRF-23269/2 capacitors have failure rate levels (FRL) established in accordance with MIL-STD-690. DLA Land and Maritime drawing 13005 capacitors are non-established reliability. TABLE II. Replacement data. MIL-PRF-23269/2 P

39、IN DLA Land and Maritime drawing PIN 13005- -001 through -057 1/ 001 through 057 7001 through 7057 101 through 157 1/ The complete MIL-PRF-23269/2 PIN shall include an additional character to indicate the FRL (3, 4, 5, or 6). Provided by IHSNot for ResaleNo reproduction or networking permitted witho

40、ut license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13005 REV A PAGE 7 6.5 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.6 Changes from previous issue.

41、 Not applicable. 6.7 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT

42、, Post Office Box 3990, Columbus, OH 43218-3990, by email to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. 6.8 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of t

43、his drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to capacitorfilterdla.mil, or by telephone (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 16299 AVX Corporation ER15 Series 3900 Electronics Drive Raleigh, NC 27604-1698 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-