DLA DSCC-DWG-13006-2012 CAPACITORS FIXED GLASS DIELECTRIC (RADIAL OR AXIAL WIRE-LEAD TERMINALS).pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV OF PAGES PAGES PMIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 11 December 2012 CHECKED BY Mark Rush TIT

2、LE CAPACITORS, FIXED, GLASS DIELECTRIC, (RADIAL OR AXIAL WIRE-LEAD TERMINALS) APPROVED BY Michael A. Radecki SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13006 SCALE N/A REV PAGE 1 OF 10 AMSC N/A 5910-2013-E03Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D

3、LA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for glass dielectric capacitors screened to MIL-PRF-23269. The capacitors described herein are possible replacements for MIL-PRF-23269/10 capacitors

4、(see 6.4 and table II). 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 13006 -001 Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does

5、 not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in s

6、ections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues

7、of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-23269 - Capacitors, Fixed, Glass Dielectric, Established Reliability, General Specification for. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or fr

8、om the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related speci

9、fication sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specifie

10、d in MIL-PRF-23269 and herein (see figure 1). 3.1.1 Case material. Epoxy. 3.1.2 Terminals. Solderable. 3.1.3 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by ma

11、ss. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A P

12、AGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. See marking requirement (see 3.8). FIGURE 1. Dimensions and configuration. Case Size L .005 W .010 S .020 51 .300 .200 .200 52 .300 .300 .200 53 .500 .300 .400 Inches mm Inches mm .002 0.05 .20

13、0 5.08 .005 0.13 .300 7.62 .010 0.25 .400 10.16 .020 0.51 .500 12.75 .050 1.27 1.25 31.75 .115 2.92 W L S 13006 -001 TM 12A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006

14、 REV A PAGE 4 3.3 Electrical characteristics. 3.3.1 Capacitance tolerance. See table I. 3.3.2 Rated voltage. 300 V dc. 3.3.3 Capacitance. When measured as specified in MIL-PRF-23269, the capacitance shall be within the applicable tolerance of the nominal value specified in table I. 3.3.4 Dissipation

15、 factor. When measured as specified in MIL-PRF-23269, the dissipation factor shall not exceed 0.2 percent (1.0 pF through 100 pF) or 0.1 percent (110 pF and up). 3.3.5 Temperature coefficient and capacitance drift (manufacturer eligibility only (see 3.9). When measured as specified in MIL-PRF-23269,

16、 the capacitors shall meet the following requirements: a. Temperature coefficient: 140 parts per million (ppm)/C 25 ppm/C. b. Capacitance drift: 0.1 percent or 0.1 pF, whichever is greater. 3.3.6 Insulation resistance (IR). When measured as specified in MIL-PRF-23269, the insulation resistance shall

17、 be 100,000 megohms, minimum, at +25C. 3.3.7 Quality factor (Q) (manufacturer eligibility only (see 3.9). 500 minimum (1.0 pF through 100 pF) or 1,000 minimum (110 pF and up). 3.4 Seal. In accordance with MIL-PRF-23269, test II. 3.5 Thermal shock and moisture resistance (manufacturer eligibility gro

18、up C (see 3.9). In accordance with MIL-PRF-23269. The following detail shall apply: Dissipation factor: 0.3 percent maximum (1 pF through 100 pF) or 0.1 percent maximum (110 pF and up). 3.6 Thermal shock (group A inpection): In accordance with MIL-PRF-23269. The following details shall apply: a. Cap

19、acitance: Within the tolerance specified (see table I). b. Dissipation factor: Within the initial limits. 3.7 Life (manufacturer eligibility only (see 3.9). In accordance with MIL-PRF-23269. The following details shall apply: a. Capacitance (240 hours and 2,000 hours): 0.5 percent or 0.5 pF, maximum

20、. b. Dissipation factor (240 hours and 2,000 hours): 0.45 percent maximum (1.0 pF through 100 pF) or 0.25 percent maximum (100 pF and up). 3.8 Marking. In accordance with MIL-PRF-23269, except the capacitor shall be marked with the PIN as specified herein (see 1.2. 13006 DLA Land and Maritime drawin

21、g number -001 Non-significant dash number TM 12A | Trademark Year Sequential 4 week lot code code 3.9 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-23269 Qualified Products Database for at least one part, or perfor

22、m the group A and group C inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum exte

23、nt possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A

24、 CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 5 3.11 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.12 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life

25、, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-PRF-23269. 5. PACKAGING 5.1

26、 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging

27、requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys aut

28、omated packaging files, CD-ROM products, or by contacting the responsible packaging activity. TABLE I. Electrical characteristics. DLA Land and Maritime drawing (PIN) 13006- Capacitance (pF) Capacitance tolerance Case size 51 001 1.0 0.25 pF 002 1.5 0.25 pF 003 2.2 0.25 pF 004 2.7 0.25 pF 005 3.0 0.

29、25 pF 006 3.3 0.25 pF 007 3.6 0.25 pF 008 3.9 0.25 pF 009 4.3 0.25 pF 010 4.7 0.25 pF 011 5.1 0.25 pF 012 5.1 5% 013 5.6 0.25 pF 014 5.6 5% 015 6.2 0.25 pF 016 6.2 5% 017 6.8 0.25 pF 018 6.8 5% 019 7.5 0.25 pF 020 7.5 5% 021 8.2 0.25 pF 022 8.2 5% 023 9.1 0.25 pF Provided by IHSNot for ResaleNo repr

30、oduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 6 TABLE I. Electrical characteristics. - Continued. DLA Land and Maritime drawing (PIN) 13006- Capacitance (pF) Capacitance tolerance 024 9.1 5% 025

31、 10 0.25 pF 026 10 5% 027 11 0.25 pF 028 11 5% 029 12 0.25 pF 030 12 5% 031 13 0.25 pF 032 13 2% 033 13 5% 034 15 0.25 pF 035 15 2% 036 15 5% 037 16 0.25 pF 038 16 2% 039 16 5% 040 18 0.25 pF 041 18 2% 042 18 5% 043 20 0.25 pF 044 20 2% 045 20 5% 046 22 0.25 pF 047 22 2% 048 22 5% 049 24 0.25 pF 050

32、 24 2% 051 24 5% 052 27 1% 053 27 2% 054 27 5% 055 30 1% 056 30 2% 057 30 5% 058 33 1% 059 33 2% 060 33 5% 061 36 1% 062 36 2% 063 36 5% 064 39 1% 065 39 2% 066 39 5% 067 43 1% 068 43 2% 069 43 5% Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA L

33、AND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 7 TABLE I. Electrical characteristics. - Continued. DLA Land and Maritime drawing (PIN) 13006- Capacitance (pF) Capacitance tolerance 070 47 1% 071 47 2% 072 47 5% 073 51 1% 074 51 2% 075 51 5% 076 56 1% 077 56 2% 0

34、78 56 5% 079 62 1% 080 62 2% 081 62 5% 082 68 1% 083 68 2% 084 68 5% 085 75 1% 086 75 2% 087 75 5% 088 82 1% 089 82 2% 090 82 5% 091 91 1% 092 91 2% 093 91 5% 094 100 1% 095 100 2% 096 100 5% 097 110 1% 098 110 2% 099 110 5% 100 120 1% 101 120 2% 102 120 5% 103 130 1% 104 130 2% 105 130 5% 106 150 1

35、% 107 150 2% 108 150 5% 109 160 1% 110 160 2% 111 160 5% 112 180 1% 113 180 2% 114 180 5% 115 200 1% Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 8 TABLE I.

36、Electrical characteristics. - Continued. DLA Land and Maritime drawing (PIN) 13006- Capacitance (pF) Capacitance tolerance 116 200 2% 117 200 5% 118 220 1% 119 220 2% 120 220 5% 121 240 1% 122 240 2% 123 240 5% 124 270 1% 125 270 2% 126 270 5% 127 300 1% 128 300 2% 129 300 5% 130 330 1% 131 330 2% 1

37、32 330 5% 133 360 1% 134 360 2% 135 360 5% 136 390 1% 137 390 2% 138 390 5% 139 430 1% 140 430 2% 141 430 5% 142 470 1% 143 470 2% 144 470 5% 145 510 1% 146 510 2% 147 510 5% 148 560 1% 149 560 2% 150 560 5% Case size 52 201 620 1% 202 620 2% 203 620 5% 204 680 1% 205 680 2% 206 680 5% 207 750 1% 20

38、8 750 2% 209 750 5% 210 820 1% Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 9 TABLE I. Electrical characteristics. - Continued. DLA Land and Maritime drawing

39、 (PIN) 13006- Capacitance (pF) Capacitance tolerance 211 820 2% 212 820 5% 213 910 1% 214 910 2% 215 910 5% 216 1,000 1% 217 1,000 2% 218 1,000 5% Case size 53 301 1,100 1% 302 1,100 2% 303 1,100 5% 304 1,200 1% 305 1,200 2% 306 1,200 5% 307 1,300 1% 308 1,300 2% 309 1,300 5% 310 1,500 1% 311 1,500

40、2% 312 1,500 5% 313 1,600 1% 314 1,600 2% 315 1,600 5% 316 1,800 1% 317 1,800 2% 318 1,800 5% 319 2,000 1% 320 2,000 2% 321 2,000 5% 322 2,200 1% 323 2,200 2% 324 2,200 5% 325 2,400 1% 326 2,400 2% 327 2,400 5% 6. NOTES (This section contains information of a general or explanatory nature which may

41、be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively

42、 to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. Provided by IHS

43、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13006 REV A PAGE 10 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements f

44、or delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for notification of change of product to the acquiring activity, if applicable. d. Requirements for p

45、ackaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on pr

46、oducts that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard

47、Specification for Electrodeposited Coatings of Tin). 6.4 MIL-PRF-23269/10 replacements. The capacitors described herein are possible replacements for MIL-PRF-23269/10 capacitors. Users are cautioned to evaluate this document for their particular application before citing it as a replacement document

48、. MIL-PRF-23269/10 capacitors have failure rate levels (FRL) established in accordance with MIL-STD-690. DLA Land and Maritime drawing 13006 capacitors are non-established reliability. TABLE II. Replacement data. MIL-PRF-23269/10 PIN 1/ DLA Land and Maritime drawing PIN 13006- -001 through -150 001 through 150 -201 through -218 201 through 218 -301 thr