DLA DSCC-DWG-13016-2013 ATTENUATORS FIXED MINIATURE COAXIAL LINE (SMA CONNECTORS) FREQUENCY RANGE DC TO 18 GHz CLASS IV LOW POWER.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 REV STATUS REV OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Michael A. Radecki DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 2 April 2013 CHECKED BY Andrew R. Ernst TITLE ATT

2、ENUATORS, FIXED, MINIATURE, COAXIAL LINE (SMA CONNECTORS), FREQUENCY RANGE: DC TO 18 GHz, CLASS IV, LOW POWER APPROVED BY Robert M. Heber SIZE A CODE IDENT. NO. 037Z3 DWG NO. 13016 SCALE N/A REV PAGE 1 OF 6 AMSC N/A 5985-2013-E04Provided by IHSNot for ResaleNo reproduction or networking permitted wi

3、thout license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13016 REV PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for fixed coaxial line (series S and N) attenuators screened to MIL-DTL-3933. The attenuators described herein are direct r

4、eplacements for screened (S) and non-screened (N) MIL-DTL-3933/25 attenuators that lost their qualified MIL-DTL-3933 source (see 6.4 and table II). 1.2 Part or Identifying Number (PIN). The complete PIN will be in the following form: 13016 -22N Drawing Dash number number (see table I) 2. APPLICABLE

5、DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to

6、 ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, and 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following

7、 specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-3933 - Attenuators, Fixed, Space Level, Non-S

8、pace Level, General Specification for. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch or from the DLA Document Service Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the con

9、tract, in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has bee

10、n obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-DTL-3933 and herein (see figure 1). 3.1.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of

11、 capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.2 Rated temperature. -55C to +125C. 3.3 Maximum weight. 0.45 ounces. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

12、 from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13016 REV PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parentheses. 4. Dimension A is listed in table I. FIGURE 1. Dimension

13、s and configuration. 3.4 Electrical characteristics. 3.4.1 Nominal impedance. 50 ohms. 3.4.2 Attenuation: See table I. Stability and sensitivity: Frequency sensitivity, maximum: 0.4 dB/dB/GHz. Temperature sensitivity of attenuation, maximum: 0.0006 dB/dB/C. 3.4.3 Power. See table I. Power sensitivit

14、y for full input power, maximum: 0.005 dB/dB/Watt. 3.4.4 VSWR. See table I. 3.4.5 Connector repeatability. Maximum variation in attenuation: 0.04 dB. Maximum attenuation change after: Up to 10 dB, inclusive (dB) Over 10 dB (dB/dB) Temperature change / thermal shock 0.5 0.05 Vibration or shock 0.5 0.

15、05 Moisture resistance or salt spray 0.5 0.05 Peak power 0.5 0.05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13016 REV PAGE 4 3.5 Engineering data. 3.5.1 Operating frequenc

16、y range. DC to 18 GHz (see table I). 3.5.2 Test frequency range. 3.5.2.1 For VSWR and attenuation measurements, measured or recorded, when using an Automatic Network Analyzer (ANA) or equivalent test equipment: 100 MHz (or lower) to 2.0 GHz for dash numbers 22 through 26. 100 MHz (or lower) to 18 GH

17、z for dash numbers 89 through 90. 3.5.2.2 Basic test frequency for sensitive measurements like connector repeatability, temperature sensitivity, power sensitivity and any other measurements where a delta specification is imposed: 1.0 GHz for dash numbers 22 through 26. 8.0 GHz for dash numbers 89 th

18、rough 90. TABLE I. Electrical characteristics. Dash number Attenuation (dB) Maximum Power Input VSWR maximum 3/ Dimension A (inches) maximum Nominal Deviation AV (W) 1/ (continuously) Peak (W) 2/ DC to 2.0 GHz 2 to 4.0 GHz 4 to 8.0 GHz 8 to 12.4 GHz 12.4 to 18.0 GHz DC to 2.0 GHz DC to 4.0 GHz DC to

19、 8.0 GHz DC to 12.4 GHz DC to 18.0 GHz 22 N S 22 0.5 - - - - 2 500 1.15:1 - - - - 1.03 (26.16) 24 N S 24 0.5 - - - - 2 500 1.15:1 - - - - 1.03 (26.16) 26 N S 30 0.5 - - - - 2 500 1.15:1 - - - - 1.03 (26.16) 89 N S 25 0.3 - - - 1.0 2 500 1.10:1 1.15:1 1.20:1 1.25:1 1.35:1 1.04 (26.42) 90 N S 30 0.6 -

20、 - - 1.0 2 500 1.10:1 1.15:1 1.20:1 1.25:1 1.35:1 1.04 (26.42) 1/ Power input is derated linearly to 0.5 watts at +125C. 2/ Peak power for a duty cycle of 5 x 10-4 ;maximum pulse duration 5 microseconds. 3/ VSWR value is for both ends. 3.6 Marking. In accordance with MIL-DTL-3933, except the attenua

21、tor shall be marked with the PIN as specified herein (see 1.2). 13016-22N - Drawing PIN 12345 - Manufacturers source code or logo 1305 - Date code XXXX - Serialization 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-

22、DTL-3933 Qualified Products Database for at least one part, or provide evidence that their parts have passed the qualification requirements of MIL-DTL-3933. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply.

23、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13016 REV PAGE 5 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally prefer

24、able materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. The attenuator shall be uniform in quality and free from any defects that

25、will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. For N level product, inspection of product for delivery shall consist of the group A inspecti

26、on of MIL-DTL-3933. For S level product, inspection of product for delivery shall consist of screening and the group A inspection of MIL-DTL-3933. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging

27、 of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or D

28、efense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information

29、 of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Attenuators conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM ap

30、plication. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and w

31、ill not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each

32、shipment of parts by the manufacturer. c. Requirements for notification of change of product to the acquiring activity, if applicable. d. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growt

33、h problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. A

34、lloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 MIL-DTL-3933/25 replacements. The attenuators described herein are direct replacements

35、for some of the MIL-DTL-3933/25 screened and non-screened attenuators (see table II). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13016 REV PAGE 6 TABLE II. Replacement data

36、 MIL-DTL-3933/25 PIN DLA Land and Maritime drawing PIN 13016- M3933/25-22N 22N M3933/23-22S 22S M3933/25-24N 24N M3933/25-24S 24S M3933/25-26N 26N M3933/25-26S 26S M3933/25-89N 89N M3933/25-89S 89S M3933/25-90N 90N M3933/25-90S 90S 1/ M3933 non-screened (N) PINs may also be known without the ending

37、 N character. 6.5 Replaceability. Attenuators covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and t

38、he users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by telephone (614) 692-0551 or DSN 850-0551. 6.7 Approved sources of

39、 supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to tubesampsdla.mil, or by telephone (614) 69

40、2-0551 or DSN 850-0551. Vendor Vendor CAGE Vendor name and address Similar designation 1/ A 95077 SV Microwave 2400 Centrepark West Drive Suite 100 West Palm Beach, FL 33409-6469 SF0965-6811-XXX 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-