DLA DSCC-DWG-13017 REV B-2013 CAPACITORS FIXED ELECTROLYTIC (NONSOLID ELECTROLYTE) TANTALUM (POLARIZED SLUG).pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Corrected the lead diameter tolerance in figure 1. 9 September 2013 Michael A. Radecki B Added new ratings. 16 December 2013 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS REV B B B B B B B B B B OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 P

2、MIC N/A PREPARED BY John Bonitatibus DESIGN ACTIVITY DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Original date of drawing 20 June 2013 CHECKED BY Andrew R. Ernst TITLE CAPACITORS, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM (POLARIZED SLUG) APPROVED BY Michael A. Radecki SIZE A CODE IDENT

3、. NO. 037Z3 DWG NO. 13017 SCALE N/A REV B PAGE 1 OF 10 AMSC N/A 5910-2014-E02 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing

4、 describes the complete requirements for tantalum electrolytic (nonsolid) electrolyte, fixed capacitors, in tantalum cases, insulated and uninsulated. These capacitors are similar to DLA Land and Maritime drawing 93026 capacitors with improved reverse voltage, vibration, and thermal shock capabiliti

5、es. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 13017 -01 K S Drawing Dash number Capacitance S=sleeved units Number (see table I) tolerance U=unsleeved units K=10 percent M=20 percent 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified i

6、n sections 3, 4, and 5 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet

7、 all specified requirements of documents in sections 3, 4, and 5 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified

8、 herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39006 - Capacitors, Fixed, Electrolytic (Non-Solid Electrolyte), Tantalum Established Reliability, General Specification for DEPA

9、RTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Components, Test Methods for. MIL-STD-790 - Standard Practice for Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. MIL-STD-1276 - Le

10、ads for Electronic Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of pr

11、ecedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exempt

12、ion has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 3 Case size Dimensions mm (inches) Basic case Insulated case L +0.79 (.031) -0.41 (.016)

13、D 0.41 (.016) D Max E 6.35 (.250) T1 11.51 (.453) 4.78 (.188) 5.56 (.219) 38.10 (1.500) T2 16.28 (.641) 7.14 (.281) 7.92 (.312) 57.15 (2.250) T3 19.46 (.766) 9.52 (.375) 10.31 (.406) 57.15 (2.250) T4 26.97 (1.062) 9.52 (.375) 10.31 (.406) 57.15 (2.250) NOTES: 1. Dimensions are in millimeters. 2. Inc

14、hes are in parentheses. 3. The weld shall not be enclosed in the end seal. FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PA

15、GE 4 FIGURE 2. Voltage derating with temperature. 3. REQUIREMENTS 3.1 Design and physical dimensions. The design and physical dimensions shall be as specified herein (see figure 1). 3.1.1 Terminals. All terminals shall be permanently secured internally and externally, as applicable. All external joi

16、nts shall be welded. Terminals shall be tin-lead coated with a minimum lead content of 3 percent and conform to type N32, N51, or N52 as specified in MIL-STD-1276. The length and diameter of the terminals shall be as specified in figure 1. 3.1.2 Pure tin. The use of pure tin, as an underplate or fin

17、al finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.1.3 Case. The case shall be made of tantalum. 3.1.4 Sleeving (when applicable). Shr

18、ink fitted insulation shall be used for the sleeving, and it shall lap over the ends of the capacitor body. 3.1.5 Capacitor element. The capacitor element shall consist of an anode of a sintered tantalum slug. 3.1.6 Rated temperature. The capacitor is rated for its given voltage from -55C to +85C. I

19、t is derated to two thirds of its given voltage at +125C. See figure 2 for voltage derating with temperature. 3.2 Electrical characteristics. The electrical characteristics shall be as shown in table I and table II. 3.3 Seal. When the capacitors are tested as specified in MIL-PRF-39006, there shall

20、be no evidence of leakage. 3.4 Solderability. Solderability shall be in accordance with MIL-PRF-39006. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 5 3.5 Sta

21、bility at high and low temperature. Stability at high and low temperature shall be in accordance with MIL-PRF-39006. 3.6 Additional tests. The capacitors specified herein are designed to meet the following requirements. Whether the tests are actually performed or not shall be at the option of the ac

22、quiring activity (see 6.2c) and shall be negotiable with the manufacturer. 3.6.1 Shock. The capacitors shall meet the requirements of MIL-PRF-39006 when tested in accordance with test condition I, method 213 of MIL-STD-202. 3.6.2 Vibration. 3.6.2.1 Vibration, high frequency. The capacitors shall mee

23、t the requirements of MIL-PRF-39006 when tested in accordance with method 204 of MIL-STD-202, test condition E (50 g). 3.6.2.2 Vibration, random. The capacitors shall meet the requirements of MIL-PRF-39006 when tested in accordance with method 214 of MIL-STD-202, test condition II-G (27.78 g). 3.6.3

24、 Thermal shock. Thermal shock shall be in accordance with MIL-PRF-39006 when tested for 300 cycles. 3.6.4 Salt atmosphere (corrosion). Salt atmosphere shall be in accordance with MIL-PRF-39006. 3.6.5 Terminal strength. Terminal strength shall be in accordance with MIL-PRF-39006. 3.6.6 Surge voltage.

25、 Surge voltage shall be in accordance with MIL-PRF-39006 and table II of this drawing. 3.6.7 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-39006. 3.6.8 Dielectric withstanding voltage. Dielectric withstanding voltage shall be in accordance with MIL-PRF-39006. 3.6.9 Ins

26、ulation resistance. Insulation resistance shall be in accordance with MIL-PRF-39006. 3.6.10 Low temperature storage. Low temperature storage shall be in accordance with MIL-PRF-39006. 3.6.11 Reverse voltage. Reverse voltage shall be in accordance with MIL-PRF-39006, except the dc potential shall be

27、1.5 V, maximum. 3.6.12 Life. The capacitors shall be capable of withstanding a 2,000 hour life test at +85C at rated voltage, or a 1,000 hour life test at +125C test at derated voltage. After the test, the capacitors shall meet the following requirements: a. DC leakage at (+85C and +125C) shall not

28、exceed 125 percent of the specified value (see table I). b. DC leakage at (+25C) shall not exceed the specified value (see table I). c. Capacitance shall be within +10, -20 percent of initial value. d. ESR shall not exceed 200 percent of the specified value (see table I). e. Dielectric withstanding

29、voltage in accordance with MIL-PRF-39006. f. Insulation resistance in accordance with MIL-PRF-39006. g. Visual examination shall show no damage, obliteration of marking, or leakage of electrolyte. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA L

30、AND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 6 3.6.13 AC ripple life. AC ripple life shall be in accordance with MIL-PRF-39006 and shall not exceed the specified value (see table I and table III). 3.6.13.1 AC ripple current multipliers vs. frequency, temperatu

31、re, and applied voltage. See table III. 3.6.14 Impedance. Impedance shall be in accordance with MIL-PRF-39006 and shall not exceed the specified value (see table I). 3.6.15 Barometric pressure (reduced). Barometric pressure shall be in accordance with MIL-PRF-39006. 3.6.16 Resistance to solvents. Re

32、sistance to solvents shall be in accordance with MIL-PRF-39006. 3.6.17 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-39006. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with the manufacture

33、rs name or CAGE code, date code, lot symbol, capacitance (in F), and rated voltage. 3.8 Manufacturer Eligibility. To be eligible to be listed as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-39006 Qualified Products List for at least one style or perform all testing spe

34、cified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime - VAT. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.10 Recycled, recovered, or environmentally preferable m

35、aterials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.11 Workmanship. Capacitors shall b

36、e uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-39006 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Qualifica

37、tion inspection. Qualification inspection is not applicable to this document. 4.3 Failure rate qualification. The failure rate qualification specified in MIL-PRF-39006 is not applicable to this document. 4.4 Quality conformance inspections. 4.4.1 Inspection of product for delivery. Inspection of pro

38、duct for delivery shall consist of the group A inspection and subgroup 1 of the group B inspection of MIL-PRF-39006. 4.5 Visual and mechanical examination. Capacitors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance

39、 with applicable requirements of MIL-PRF-39006. 4.6 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specifie

40、d in the contract or purchase order, the contractor may use their own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth herein where

41、 such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 7 TAB

42、LE I. Electrical characteristics. DLA Land and Maritime Drawing PIN 13017- 1/ Cap. (F) at +25C and 120 Hz Case size Max ESR Ohms 120 Hz Max DCL uA Max impedance ohms at -55C 120 Hz Maximum capacitance change in percent AC ripple +85C 40 KHz mA rms 2/ +25C +85C and +125C -55C +85C +125C 25 V dc at +8

43、5C 15 V dc at +125C 01 - - 120 T1 1.30 1 5 25 -42 8 12 1250 02 - - 560 T2 0.83 2 10 12 -65 14 18 2000 03 - - 1200 T3 04 - - 1800 T4 30 V dc at +85C 20 V dc at +125C 05 - - 100 T1 1.30 1 5 25 -38 8 12 1200 06 - - 470 T2 0.85 2 10 15 -65 14 18 1800 07 - - 1000 T3 08 - - 1500 T4 50 V dc at +85C 30 V dc

44、 at +125C 09 - - 68 T1 1.50 1 5 35 -25 8 15 1050 10 - - 220 T2 0.90 2 10 17.5 -50 8 15 1800 11 - - 470 T3 0.75 3 25 10 -45 8 15 2100 12 - - 680 T4 0.70 5 40 8 -58 10 20 2700 60 V dc at +85C 40 V dc at +125C 13 - - 47 T1 2.00 1 5 44 -25 8 12 1050 14 - - 150 T2 1.10 2 10 20 -40 8 15 1800 15 - - 390 T3

45、 0.90 3 25 15 -45 8 15 2100 16 - - 560 T4 0.80 5 40 10 -58 8 15 2700 75 V dc at +85C 50 V dc at +125C 17 - - 33 T1 2.50 1 5 66 -25 5 9 1050 18 - - 110 T2 1.30 2 10 24 -35 6 10 1650 19 - - 330 T3 1.00 3 30 12 -45 6 10 2100 20 - - 470 T4 0.90 5 50 12 -50 6 10 2700 100 V dc at +85C 65 V dc at +125C 21

46、- - 15 T1 3.50 1 5 125 -18 3 10 1050 22 - - 68 T2 2.10 2 10 37 -30 4 12 1650 23 - - 150 T3 1.60 3 25 22 -35 6 12 2100 24 - - 220 T4 1.20 5 50 15 -40 6 12 2700 125 V dc at +85C 85 V dc at +125C 25 - - 10 T1 5.50 1 5 175 -15 3 10 1050 26 - - 47 T2 2.30 2 10 47 -25 5 12 1650 27 - - 82 T3 1.80 3 25 40 -

47、35 5 12 1950 28 - - 100 T3 1.80 3 25 35 -35 5 12 2100 29 - - 150 T4 1.60 5 50 20 -35 6 12 2700 1/ The complete PIN number shall include symbols to indicate capacitance tolerance and sleeved or unsleeved units (see 1.2). 2/ For ripple current limits at various temperatures, voltages, and frequencies

48、see table III. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 13017 REV B PAGE 8 TABLE II. Voltage. Voltage Rated (+85C) Volts, dc. Derated (+125C) Volts, dc. Surge (+85C) Volts, dc. 25 30 50 60 75 100 125 15 20 30 40 50 65 85 28.8 34.5 57.5 69.0 86.3 115.0 144.0 TABLE III. Ripple current multipliers vs. Frequency, temperature and applied voltage. 1/ 2/ Frequency of applied ripple current 120 Hz 800 Hz 1 kHz Ambient still air temperature in C +55 +85 +105 +125 +55