DLA DSCC-DWG-84006 REV D-2004 HOLDER ELECTRICAL CARD CARD GUIDE SHALLOW CHANNEL PLASTIC《塑料的 有浅层通道和插件导轨的电动卡座》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Addition of marking requirement and source of supply. 22 OCT 1984 Randy Larson B Changed marking requirements and changed dimensional tolerance on snap retainer. Editorial changes. 14 JAN 1988 Randy Larson C Change FSC from 5999 to 5998. Editorial changes t

2、hroughout. 12 JUL 2000 Monica L. Poelking D Added additional suggested source of supply. Editorial changes throughout. 22 NOV 2004 Thomas M. Hess THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV STATUS REV D D D D

3、D D D D OF PAGES PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 454445000 Original date of drawing 18 Jun 1984 CHECKED BY Randy Larson TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Ivan Jones SHALLOW CHANNEL, PLASTIC SIZE

4、A CODE IDENT. NO. 14933 DWG NO. 84006 REV D PAGE 1 OF 8 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/programs/milspec/docsearch.aspAMSC N/A 5998-E050 DISTRIBUTION STATEMENT A. Approved for public rele

5、ase; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of card guides intended for use with printed circuit boards and circuit card assemblies. 1.2 Part

6、or Identifying Number (PIN). The complete PIN shall be as follows: 84006 Drawing number 01 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in

7、other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this speci

8、fication, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those

9、cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE STANDARDS MILSTD1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.assist.daps.dla.mil or from the Standardization Document Order Desk

10、, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191115094.) 2.3 NonGovernment publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract (see 6.2). ASTM

11、 INTERNATIONAL (ASTM) ASTM D4066 Nylon Injection and Extrusion Materials (PA). (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 194282959 or at URL http:/www.astm.org.) (Non-Government Standards and other publications ar

12、e normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited

13、herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84006 REV D PAGE 2 Provided by IHSNot fo

14、r ResaleNo reproduction or networking permitted without license from IHS-,-,-3. REQUIREMENTS 3.1 Interface and physical dimensions. For dash number 01 through 12, see figure 1 and table I. For dash number 13 through 24, see figure 2 and table II. 3.2 Material. Material shall be nylon in accordance w

15、ith ASTM D4066, D4066PA211R13A999F24. 3.3 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.4 Marking. Marking of the card guide is not required; however, each unit package shall be marked in accordance with M

16、IL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to

17、the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Workmanship. Card guides shall be free of flash, pits, voids, and excessive mold marks. Visible parting line is acceptabl

18、e. Inches mm Inches mm Inches mm .005 .010 .078 0.13 0.25 1.98 .125 .188 .281 3.18 4.78 7.14 .307 .500 7.80 12.70 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 inch for two place decimals and .005 fo

19、r three place decimals. 4. Slotting or elongating of second mounting hole is recommended to allow for length variations in molding and to facilitate assembly. FIGURE 1. Dimensions of twosnap card guides. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84006 REV D P

20、AGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Physical characteristics of two snap card holders. DSCC PIN 84006 Dimension L .062 (1.57) Dimension A +.016, .032 (0.41) (0.81) Dimension B .047 (1.19) Dimension C 01 02 03 04 05 06 07 08

21、 09 10 11 12 2.500 (63.50) 3.000 (76.20) 3.500 (88.90) 4.000 (101.60) 4.500 (114.30) 5.000 (127.00) 5.500 (139.70) 6.000 (152.40) 6.500 (165.10) 7.000 (177.80) 7.500 (190.50) 8.000 (203.20) 1.516 (38.51) 1.516 (38.51) 1.516 (38.51) 3.016 (76.61) 3.016 (76.61) 3.016 (76.61) 5.016 (127.41) 5.016 (127.

22、41) 5.016 (127.41) 6.031 (153.19) 6.031 (153.19) 6.031 (153.19) .500 (12.70) 1.000 (25.40) 1.500 (38.10) .500 (12.70) 1.00 (25.40) 1.500 (38.10) 2.000 (50.80) .500 (12.70) 1.000 (25.40) .500 (12.70) 1.000 (25.40) 1.500 (38.10) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .

23、078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) Inches mm Inches mm Inches mm .010 .125 0.25 3.18 .188 .312 4.78 .500 76.61NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 inch fo

24、r two place decimals and .005 for three place decimals. 4. Slotting or elongating of second mounting hole is recommended to allow for length variations in molding and to facilitate assembly. FIGURE 2. Dimensions of threesnap card guides. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO.

25、DAYTON, OHIO A 14933 84006 REV D PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Physical characteristics of three snap card holders. DSCC PIN 84006 Dimension L .062 (1.57) Dimension A +.016, .047 (0.41), (1.19) Dimension B .047 (1.1

26、9) Dimension C +.016, .032 (0.41), (0.81) Dimension D .005 (0.127) Dimension T .007 (0.178) 13 14 15 16 17 18 19 20 21 22 23 24 8.500 (215.9) 9.000 (228.6) 9.500 (241.3) 10.000 (254.0) 10.500 (266.7) 11.000 (279.4) 11.500 (292.1) 12.000 (304.8) 12.500 (317.5) 13.000 (330.2) 13.500 (342.9) 14.000 (35

27、5.6) 7.531 (191.29) 7.531 (191.29) 7.531 (191.29) 9.031 (229.39) 9.031 (229.39) 9.031 (229.39) 10.547 (267.89) 10.547 (267.89) 10.547 (267.89) 12.047 (305.99) 12.047 (305.99) 12.047 (305.99) .500 (12.7) 1.000 (25.4) 1.500 (38.1) .500 (12.7) 1.00 (25.4) 1.500 (38.1) 2.000 (50.8) .500 (12.7) 1.000 (25

28、.4) .500 (12.7) 1.000 (25.4) 1.500 (38.1) 3.766 (9566) 3.766 (95.66) 3.766 (95.66) 4.516 (114.71 4.516 (114.71 4.516 (114.71) 5.266 (133.76 5.266 (133.76 5.266 (133.76) 6.016 (152.81 6.016 (152.81 6.016 (152.81) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .078 (1.98) .093 (2.36) .093

29、 (2.36) .093 (2.36) .093 (2.36) .093 (2.36) .093 (2.36) .141 (35.81) .141 (35.81) .141 (35.81) .141 (35.81) .141 (35.81) .141 (35.81) .156 (39.62) .156 (39.62) .156 (39.62) .156 (39.62) .156 (39.62) .156 (39.62) 4. VERIFICATION 4.1 Conformance inspections. 4.1.1 Inspection of product for delivery. I

30、nspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.6). Criteria for defects are listed in 4.1.5. 4.1.2 Optional statement of compliance. The acquiring activity, at its discre

31、tion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table III, normal sampling. If one or more defects are found, the lot shall be re

32、jected. Criteria for defects are listed in 4.1.5. 4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selec

33、ting a random sample of parts in accordance with table III, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. TABLE III

34、. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,001 29 35 35,001 and over 29 40 DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. D

35、AYTON, OHIO A 14933 84006 REV D PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.1.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are

36、considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. 5. PACKAGING 5.1 Packaging. For acquisit

37、ion purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or inhouse contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Pack

38、aging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments system command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packagin

39、g files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use for OEM (original

40、equipment manufacturer) applications, design applications, and logistics purposes. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that

41、parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Replaceability. Card holders covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.4 Users of re

42、cord. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office B

43、ox 3990, Columbus, OH 432183990 or by electronic mail at “5998.Documentsdscc.dla.mil” or by facsimile (614) 693-1642 or DSN 850-6939. 6.5 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use o

44、f this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43218-3990 or by electronic mail “5998.Documentsdscc.dla.mil” or by facsimile (614) 693-1642 or DSN 850-6939. Electronic copies of this document can be obtained on the World Wide Web from URLs

45、 http:/www.dscc.dla.mil/Downloads/MilSpec/DsccDwg/84006.pdf or http:/www.dscc.dla.mil/Programs/MilSpec/DocSearch.asp. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84006 REV D PAGE 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

46、ense from IHS-,-,-DSCC drawing PIN Vendor similar designation or type number 1/ DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 8400601 8400602 8400603 8400604 8400605 8400606 8400607 8400608 8400609 8400610 8400611 8400612 CG3125 CG3130 CG3135 CG314

47、0 CG3145 CG3150 CG3155 CG3160 CG3165 CG3170 CG3175 CG3180 8400613 8400614 8400615 8400616 8400617 8400618 8400619 8400620 8400621 8400622 8400623 8400624 CG3185 CG3190 CG3195 CG31100 CG31105 CG31110 CG31115 CG31120 CG31125 CG31130 CG31135 CG31140 53507 Airquip Robleyco (A division of Micro Dimension

48、al Products, Inc.) 199 West Spruce Street Norristown, PA 19401-3863 Phone: (610) 239-7990 Facsimile: (610) 239-7980 e-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DSCC drawing PIN Vendor similar designation or type number 1/ DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 8400601 8400602 8400603 8400604 8400605 8400606 8400607 8400608 8400609 8400610 8400611