DLA DSCC-DWG-84082 REV E-2010 FILTERS AND CAPACITORS RADIO FREQUENCY ELECTROMAGNETIC INTERFERENCE SUPPRESSION HERMETICALLY SEALED ON ONE END ONLY.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Page 3 - 3.7, changed manufacturer eligibility requirement. Pages 6 and 7 - Added an additional suggested source of supply. 21 Dec 87 David W. Withrow B Page 3 - Change paragraph reference. Page 6 - Added caution note concerning soldering temperature. Page

2、7 - Deleted one source of supply. Added a new source of supply. 22 Jun 90 D. Moore C Editorial changes throughout. Removed one source of supply. 8 Aug 2000 K. A. Cottongim D Editorial changes throughout. 28 July 2005 K. A. Cottongim E Editorial changes throughout. Added pure tin prohibition paragrap

3、hs 3.1.4 and 6.4. Deleted paragraph 4.2.3, Inspection of packaging. 2 Dec 2010 M. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV E E E E E E E PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Randy Larson DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAY

4、TON, OH Original date of drawing 11 Sep 84 CHECKED BY David E. Moore TITLE FILTERS AND CAPACITORS, RADIO FREQUENCY/ ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED ON ONE END ONLY APPROVED BY Randy Larson SIZE A CODE IDENT. NO. 14933 DWG NO. 84082 REV E PAGE 1 OF 7 AMSC N/A 59GP-2011-E

5、03 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082

6、 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-28861 describe the requirements for radio frequency interference filters and capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 84082 - XXX | | | | | | Drawing Dash number number (see table I) 2. APPLICAB

7、LE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the c

8、ompleteness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standar

9、ds, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-28861 - Filters and Capacitors, Radio Frequency/Electromagne

10、tic Interference Suppression, General Specification for DEPARTMENT OF DEFENSE STANDARDS MIL-STD-220 - Method of Insertion Loss Measurement. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from th

11、e Standardization Document Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes

12、precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-28861 and herein. 3.1.1 Terminals. Te

13、rminals shall be solderable and in accordance with figure 1 herein. 3.1.2 Case dimensions. The case dimensions shall be in accordance with figure 1 herein. 3.1.3 Finish. The case and lead finish shall be gold plated as specified in MIL-PRF-28861. 3.1.4 Pure tin prohibition. Pure tin shall be prohibi

14、ted as specified in MIL-PRF-28861 (see 6.4). 3.1.5 Weight. The weight shall be as follows: For C circuit parts - .25 gram, maximum. For L circuit parts - .75 gram, maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CE

15、NTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082 REV E PAGE 3 3.2 Operating temperature range. The operating temperature range shall be -55C to +150C. 3.3 Temperature rise. The temperature rise shall be +35C maximum. 3.4 Electrical characteristics. 3.4.1 Rated voltage. The rated voltage

16、shall be in accordance with table I. 3.4.2 Rated current. The rated current shall be 10 amperes maximum. 3.4.3 Rated frequency. The rated frequency shall be dc. 3.4.4 Capacitance. Capacitance shall be in accordance with table I. 3.4.5 Voltage and temperature limits of capacitance. Voltage and temper

17、ature limits of capacitance shall be +15, -40 percent. 3.4.6 Insulation resistance. Insulation resistance shall be as follows: At +25C: 1,000 megohm-microfarads or 100,000 megohms minimum, whichever is less. At +125C: 100 megohm-microfarads or 10,000 megohms minimum, whichever is less. 3.4.7 Inserti

18、on loss. Insertion loss shall be as follows: At +25C: In accordance with table I. At -55C and +150C: A 3 dB degradation from the +25C value shall be allowed. 3.4.8 Voltage drop. Voltage drop shall be .10 V dc. 3.4.9 DC resistance. DC resistance shall be 0.01 ohm, maximum. 3.5 Environmental and mecha

19、nical requirements. The environmental and mechanical requirements shall be in accordance with MIL-PRF-28861 for class B, non-hermetically sealed filters. The following details and exceptions shall apply. 3.51 Solderability of terminals. Solderability of terminals shall be in accordance with MIL-PRF-

20、28861, except temperature of solder shall be +300C 5C. 3.5.2 Resistance to soldering heat. Resistance to soldering heat shall be in accordance with MIL-PRF-28861, except temperature of solder shall be +300C 5C. 3.5.3 Solderability of mounting termination. Solderability of mounting termination shall

21、be in accordance with MIL-PRF-28861, except temperature of solder shall be +300C 5C. 3.6 Product assurance level. Class B only. 3.7 Marking. Filters and capacitors shall not be marked. The unit package shall be marked in accordance with MIL-STD-1285, except the part number shall be as specified in 1

22、.2 with the manufacturers name or code, date code, voltage rating, and current rating. 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-28861 Qualified Products List for at least one part or, perform first article

23、 inspection in accordance with the MIL-PRF-28861 qualification inspection requirements for class B. 3.9 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material

24、meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.10 Workmanship. Filters and capacitors shall be processed in such a manner as to be uniform in quality and shall be free from cold soldering, corrosion, pits, dents, cracks, roug

25、h or sharp edges, misalignments, and other defects that will affect life, serviceability, or appearance. Cracks in glass seals are not allowed; however, minor meniscus crazing is acceptable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELE

26、CTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082 REV E PAGE 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005. 4. Circuit diagram is for information only. 5. Filters shall

27、 be supplied with 60/40 solder preform. 6. Potting on nonhermetically sealed end shall not extend beyond .030 inch from the filter body. 7. Filters shall be installed using the recommended installation methods in 6.6.1.3 (solder-in style paragraph) of MIL-PRF-28861. FIGURE 1. Circuit diagrams and ca

28、se and hardware dimensions.Inches mm .002 .005 .025 .030 .03 .032 .150 .165 .200 .250 .650 .750 0.05 0.13 0.64 0.76 0.8 0.81 3.81 4.19 5.08 6.35 16.51 19.05 Dimensions Circuit diagram A .005 B Ref L C .250 .150 .750 .650 Dash No. Configuration 001 through 012 1 013 through 024 2 Provided by IHSNot f

29、or ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082 REV E PAGE 5 TABLE I. Electrical characteristics. Dash Number Circuit Rated voltage dc volts Capacitance (F) -0, +100 percent Minimu

30、m insertion loss (dB) in accordance with MIL-STD-220 1/ 2/ 1 MHz 10 MHz 100 MHz 1 GHz 10 GHz 001, 013 002, 014 L C 50 50 .065 .065 16 16 36 35 51 45 70 70 70 70 003, 015 004, 016 L C 100 100 .040 .040 12 12 33 31 49 43 65 65 70 70 005, 017 006, 018 L C 100 100 .027 .027 10 10 30 30 48 42 65 65 70 70

31、 007, 019 008, 020 L C 100 100 .015 .015 7 7 25 25 45 40 60 55 60 60 009, 021 010, 022 L C 200 200 .010 .010 4 4 20 20 38 35 55 52 60 60 011, 023 012, 024 L C 200 200 .005 .005 - - 15 15 35 34 55 50 60 60 1/ For C circuits, insertion loss measurements shall be made under no load. For L circuits, ins

32、ertion loss measurements shall be made under full load over the frequency range of 1 MHz to 10 MHz. Insertion loss measurements above and below this frequency range shall be made under no load. 2/ The insertion loss requirements between any two adjacent frequencies shall be that of the lower of the

33、two frequencies in order to accommodate resonant dips. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of MIL-P

34、RF-28861 for class B. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certification of compliance with group B requirements in lieu of performing group B tests (see 6.2c). 5. PACKAGING 5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall

35、 be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained b

36、y the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by conta

37、cting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082 REV E PAGE 6 6. NOTES (This section contains information of a general

38、or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Filters conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This dra

39、wing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28861, this drawing becomes obsolete and will no

40、t be used for new design. The QPL-28861 product shall be the preferred item for all applications. 6.2 Acquisition data. The acquisition document should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data with each shipment of

41、parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. d. Requirements for notification of change of product to acquiring activity, if applicable. e. Requirements for packaging and packing. 6.3 Soldering te

42、mperature. Caution: These devices should not be exposed to soldering temperatures exceeding 300C. Exposure time to soldering temperature of 300C should not exceed one minute. 6.4 Pure tin prohibition. Pure tin is prohibited since it may result in tin whisker growth. The use of alloys with tin conten

43、t greater than 97 percent may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions on products that use such materials. Conformal coatings applied over top of a whisker-prone sur

44、face will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coating of Tin). 6.5 Users of record. Military and indu

45、stry users of his drawing should inform DLA Land and Maritime when a system application requires configuration control. DLA Land and Maritime-VAT will maintain a record of users and this list will be used for coordination and distribution of changes to this drawing. Coordination of this document for

46、 future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA-Land and Maritime, ATTN:VAT, PO Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.

47、mil, or by telephone (614) 692-4709 or facsimile (614) 693-1644. 6.6 Replaceability. Filters covered by this drawing will replace the same commercial device covered by contractor-prepared specification or drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

48、rom IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 84082 REV E PAGE 7 6.7 Approved sources of supply. The approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, c

49、ontact DLA Land and Maritime-VAT, PO Box 3990, Columbus, OH 43218-3990, by e-mail to capacitorfilterdla.mil, by telephone (614) 692-4709, or facsimile (614) 693-1644. DSCC drawing PIN 84082- Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 001 002 003 004 005 006 007 008