DLA DSCC-DWG-84101 REV E-2004 HOLDER ELECTRICAL CARD CARD GUIDE DEEP CHANNEL PLASTIC《塑料的有深层通道和插件导轨的电动卡座》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Pages 1-6, Dimensioning requirements changed to allow second source to meet drawing requirements and thereby obtain two sources of supply for drawing. 14 JUN 1985 Ivan Jones B Added marking requirements. Editorial changes throughout. 29 SEP 1987 Randy Larso

2、n C Changed marking requirements and changed dimensional tolerance on snap retainer. Editorial changes. 19 SEP 1991 Randy Larson D Editorial changes throughout. 12 JUL 2000 Monica L. Poelking E Added additional source of supply. 22 NOV 2004 Thomas M. Hess THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS

3、BEEN REPLACED. Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV STATUS REV E E E E E E E OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Christopher Rauch DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 8 August 1984 CHECK

4、ED BY Randy Larson TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Ivan Jones DEEP CHANNEL, PLASTIC SIZE A CODE IDENT. NO. 14933 DWG NO. 84101 REV E PAGE 1 OF 7 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.

5、dscc.dla.mil/programs/milspec/docsearch.aspAMSC N/A 5998-E051 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. SCOPE 1.1 Scope. This drawing describes the requirements

6、 for a family of deep channel card guides intended for use with circuit card assemblies and printed circuit boards. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 84101 Drawing number 01 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Sp

7、ecifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE STAND

8、ARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non

9、-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM D4066 - Nylon Injection and Extrusion Mater

10、ials (PA). (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or at URL http:/www.astm.org.) (Non-Government Standards and other publications are normally available from the organizations which prepare or which

11、distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this

12、 document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

13、m IHS-,-,-3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified on figure 1 and in table I. Inches mm Inches mm Inches mm Inches mm Inches mm .010 .015 .020 .25 .38 .51 .025 .032 .050 .64 .81 1.27 .062 .080 .090 1.58 2.03 2.29

14、.11 .125 .160 2.8 3.18 4.06 .250 .440 .500 6.35 11.18 12.7 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 inch (.254 mm). 4. The recommended thickness of the material to which the card guides are moun

15、ted is .047 to .090 inch (1.19 to 2.29 mm). The recommended hole diameter for the card guide feet is .187 + .003/.001 inch (4.75 + 0.08/0.02 mm). 5. Slotting or elongating of second and third mounting holes is recommended to allow for length variations in molding and to facilitate assembly. 6. PINs

16、8410101, 02, 03, 22, and 23 have no center pylon, therefore, there is no “C” dimension for these parts. FIGURE 1. Dimensions of deep channel card guides. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 3 Provided by IHSNot for ResaleNo reproduction

17、 or networking permitted without license from IHS-,-,-3.2 Material. Material shall be nylon in accordance with ASTM D4066, D4066PA211R13A999F24. 3.3 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.4 Marking.

18、 Marking of the (part name) is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.5 Recycled, recovered, or environme

19、ntally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Workmanship.

20、Card guides shall be free of flash, pits, voids, and excessive mold marks. Visible parting line is acceptable. TABLE I. Dimension of deep channel card guides. DSCC PIN 84101 Dimension A .062 (1.57) Dimension B + .000, .032 (0.81) Dimension C 1/ .015 (0.38) Dimension D .005 (0.13) 01 02 03 04 2.50 (6

21、3.5) 4.50 (114.3) 6.00 (152.4) 8.00 (203.2) 1.50 (38.1) 3.50 (88.9) 5.00 (127.0) 7.00 (177.8) N/A 1/ N/A 1/ N/A 1/ 3.50 (88.9) .080 (2.03) .080 (2.03) .080 (2.03) .080 (2.03) 22 23 24 4.50 (114.3) 6.00 (152.4) 8.00 (203.2) 3.50 (88.9) 5.00 (127.0) 7.00 (177.8) N/A 1/ N/A 1/ 3.50 (88.9) .132 (3.35) .

22、132 (3.35) .132 (3.35) 1/ PINs 8410101, 02, 03, 22, and 23 have no center pylon, therefore, “C” dimension is not applicable. 4. VERIFICATION 4.1 Conformance inspections. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of

23、 interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.6). Criteria for defects are listed in 4.1.5. 4.1.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the i

24、nspection of product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.1.5. 4.1.4 Rejected lots. If an inspection

25、lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or

26、 more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.1.5 Defective characteristics and properties. Dimensional characteristics are considered defecti

27、ve when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environment

28、al survival of the part. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6

29、 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,001 29 35 35,001 and over 29 40 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (s

30、ee 6.2). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity with

31、in the Military Department or Defense Agency, or within the Military Departments system command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (

32、This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card guides conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required func

33、tion are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspectio

34、n with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Replaceability. Card holders covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.4 Users of record. Coordination of this document for

35、 future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCCVAC, Post Office Box 3990, Columbus, OH 43218-3990 or by e

36、lectronic mail at “5998.Documentsdscc.dla.mil”or by facsimile (614) 693-1642 or DSN 850-6939. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6.5 Su

37、ggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCCVAC, Post Office Box 3990, Columbus, OH 43218-3990 or by electronic mail

38、“5998.Documentsdscc.dla.mil” or by facsimile (614) 693-1642 or DSN 850-6939. Electronic copies of this document can be obtained on the World Wide Web at URL http:/www.dscc.dla.mil/Downloads/MilSpec/DsccDwg/84101.pdf or http:/www.dscc.dla.mil/Programs/MilSpec/DocSearch.asp. DSCC drawing PIN Vendor si

39、milar designation or type number 1/ Vendor CAGE Vendor name and address 8410101 8410102 8410103 8410104 8410122 8410123 8410124 DCG2525 DCG2545 DCG2560 DCG2580 DCG2545C DCG2560C DCG2580C 53507 Airquip Robleyco (A division of Micro Dimensional Products, Inc.) 199 West Spruce Street Norristown, PA 194

40、013863 Phone: (610) 2397990 Facsimile: (610) 2397980 E-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name

41、 and address 8410101 8410102 8410103 8410104 8410122 8410123 8410124 CG42 CG44 CG46 CG48 CG44125 CG46125 CG48125 54355 AFE / Accessories for Electronics, Inc. 195-Q Central Avenue E. Farmingdale, NY 117356904 Phone: (631) 8470158 Facsimile: (631) 8470293 E-mail: URL: 1/ CAUTION: Do not use this num

42、ber for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 8410101 8410102 8410103 8410104 8410122 8410124 9425 9429 94212 94216 9449 94416 189

43、15 APW / Electronic Solutions 14100 Danielson Street Poway, CA 920646898 Phone: (858) 6794550 Toll Free: (888) 9578291 Facsimile: (858) 6794555 E-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this dra

44、wing. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and addr

45、ess 8410101 8410102 8410103 8410104 8410122 8410123 8410124 DC250 DC450 DC600 DC800 DC450130 DC600130 DC800130 32559 Bivar, Incorporated 4 Thomas Street Irvine, CA 926182512 Phone: (949) 9518808 Facsimile: (949) 9513974 E-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acq

46、uired to this number may not satisfy the performance requirements of this drawing. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 8410101 8410102 8410103 8410104 8410122 8410123 8410124 9425 9445 9460 9480 9445125 9460125 9480125 24227 Teknational I

47、ndustries, Incorporated P. O. Box 926 Ft. Meyers, FL 339020926 Phone: (585) 4736310 Facsimile: (585) 4736324 E-mail: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 84101 REV E PAGE 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-