DLA DSCC-DWG-85040 REV E-2006 CONNECTOR ELECTRICAL INSERT ARRANGEMENT MINIATURE FIVE SIZE 20 SIGNAL CONTACTS WITH TWO SIZE 8 CONTACT CAVITIES《2号8条连接槽和5号20条信号谐振器的微型镶入装置电气连接器》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Part number update. Added vendor CAGEs 60563 and 28198; deleted vendor CAGEs 25330 and 71785. 90-07-31 R Marbias B Changes in accordance with NOR 5935-R017-92. For CAGE 28198, add additional DSCC part numbers and corresponding vendor part numbers. 92-05-08 J

2、ames P. Donohue C Clarify dimension on figure 1. Change “part number” to “Part or Identifying Number (PIN)”. Editorial changes throughout. 93-10-27 James P. Donohue D Vendor CAGE 60563, PINs, delete and substitute new PINs. Editor changes throughout. 01-01-22 Robert M. Heber E Add Vendor CAGE SW884,

3、 delete MIL-STD-1344 test methods, add EIA-364 test procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV E D D E E E REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC G Dennis L. Kelly DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TIT

4、LE L. V. Olszewski APPROVED BY Richard Marbais CONNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, FIVE SIZE 20 SIGNAL CONTACTS, WITH TWO SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO.85040 Original date of drawing 8 May 1986 A REV E PAGE 1 OF 6 AMSC N/A 5935-E761-000 Provided by IHSNot for

5、 ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm .055 .056 .109 .112 .270 1.40 1.42 2.77 2.84 6.86 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified,

6、tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are shown for the pin insert front. Socket inserts are the opposite. 7. Reference documents

7、 shall be of the issue in effect on date of invitations for bid. 037Z3 85040 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE2 FIGURE 1. Insert arrangement-five size 20 signal contacts with two size 8 contact cavities. Provided by IHSNot for ResaleNo reproduction or networking per

8、mitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements of drawing 85039 and MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1. Signal contact spe

9、cification: Style A (crimp removable signal contacts): Socket: M39029/63-368. Pin: M39029/64-369. Style B (solder fixed signal contacts): Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure B-2. Shell size: Two. Shell specification: Style A: Socket: MIL-DTL-24308/2,

10、 figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designed for contact insertion and removal with the applicable military tool as follows: Contact size Tool PIN20 M819

11、69/39 - 01 with plastic tip M81969/1-02 with metal tip 037Z3 85040 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating forces (with signal con

12、tacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 0.192 3.27 0.192 1.9 Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D

13、, M, N Contact Size AWG wire size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other conditi

14、ons Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 85040 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE4 Provided by I

15、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certif

16、icate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 6/ 85040GAIP 6/ 85040GAIS 85040DAEPT 85040DAEST 85040DAEPR 85040DAESR CBC7W2M1F000-50-799.2 CBC7W2F1F000-50-799.2 CBC7W2M10000-50-799.0 CBC7W2F10000-50-7

17、99.0 85040GAEPT 85040GAEST 85040GAEPR 85040GAESR CBC7W2M1F00C-50 CBC7W2F1F00C-50 CBC7W2M1000C-50 CBC7W2F1000C-50 85040GBEPT 85040GBEST 85040GBEPR 85040GBESR DAMMY7W2PA101 DAMMY7W2SA101 DAMM7W2PA101 DAMM7W2SA101 P72PSA2D P72RSA2D P72PSA2 P72RSA2 CBM7W2M02F00C-0 CBM7W2F02F00C-0 CBM7W2M02000C-0 CBM7W2F

18、02000C-0 PAMMHW7W2P PAMMHW7W2S PAMMW7W2P PAMMW7W2S 85040NAEPT 85040NAEST 85040NAEPR 85040NAESR CBC7W2M1F00C-50-403.0 CBC7W2F1F00C-50-403.0 CBC7W2M1000C-50-403-0 CBC7W2F1000C-50-403-0 85040MAEPT 85040MAEST 85040MAEPR 85040MAESR CBC7W2M1F000-50-403.4 CBC7W2F1F000-50-403.4 CBC7W2M10000-50-403-4 CBC7W2F

19、10000-50-403-4 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full complement of signal contacts. 3/ Size 8 contacts should be ordered separate

20、ly. 4/ Size 8 contacts are snap-in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061. 6/ Pins 85040GAIP and 85040GAIS are canceled and superseded by 85040GAEPR and 85040GAESR respectively. 037Z3 85040 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE5 Pro

21、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name number and address 28198 Positronics Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale

22、, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 85040 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-