DLA DSCC-DWG-85045 REV E-2006 CONNECTOR ELECTRICAL INSERT ARRANGEMENT MINIATURE TEN SIZE 20 SIGNAL CONTACTS WITH THREE SIZE 8 CONTACT CAVITIES《2号8条连接槽和5号21条信号谐振器的微型镶入装置电气连接器》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED B Part number update. Added vendor CAGES 60563 and 28198; deleted vendor CAGES 25330 and 71785. 90-07-31 R Marbias C Reverse size 8 cavity positions “A2” and “A3”. Page 5, add DSCC part numbers and corresponding vendor part numbers for CAGE 28198. 92-05-08 Jam

2、es P. Donohue D Delete “part number” and substitute “Part or Identifying Number (PIN)”. Vendor CAGE 60563, PINs, delete and substitute new PINs. Editorial changes throughout. 01-01-22 Robert M. Heber E Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 test procedures 06-01-20 Rich

3、ard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV E D D E E E REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC G Dennis L. Kelly DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE L. V. Olszewski APPROVED BY Richard Marbais CONNECTOR, ELECTRICAL, INSERT

4、 ARRANGEMENT, MINIATURE, TEN SIZE 20 SIGNAL CONTACTS, WITH THREE SIZE 8 CONTACT CAVITIES SIZE CAGE CODE 037Z3 DWG. NO.85045 Original date of drawing 8 May 1986 A REV E PAGE 1 OF 6 AMSC N/A 5935-E765-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

5、-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm .055 .056 .109 .112 .163 .218 .271 .306 .326 .381 .570 1.40 1.42 2.77 2.84 4.14 5.54 6.88 7.77 8.28 9.68 14.48 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance for

6、three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located on TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are shown for the pin insert front. Socket inserts are the opposite. 7. Reference documents shall be of t

7、he issue in effect on date of invitations for bid. 037Z3 85045 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE2 FIGURE 1. Insert arrangement, ten size 20 signal contacts, with three size 8 contact cavities.Provided by IHSNot for ResaleNo reproduction or networking permitted witho

8、ut license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C to +125C. REQUIREMENTS: Requirements of drawing 85039 and MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1. Signal contact specifications:

9、 Style A (crimp removable signal contacts): Socket: M39029/63-368. Pin: M39029/64-369. Style B (solder fixed signal contacts): Socket: MIL-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure B-2. Shell size: Three. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure

10、1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp removable signal contacts shall be designated for contact insertion and removal with the applicable military tool as follows: Contact size Tool PIN20 M81969/39

11、- 01 with plastic tip M81969/1-02 with metal tip 037Z3 85045 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating forces (with signal contacts

12、only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maximum Minimum Maximum Signal 0.385 6.54 0.385 3.85 Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D, M,

13、N Contact Size AWG wire Size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other conditions S

14、ea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, condition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 85045 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE4 Provided by IHSNot

15、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate

16、 of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW884 6/ 85045GAEP 6/ 85045GAES 6/ 85045GBEP 6/ 85045GBES 85045DAEPT CBC13W3M1F000-50-799.2 85045DAEST CBC13W3F1F000-50-799.2 85045DAEPR CBC13W3M10000-50-799.0 8504

17、5DAESR CBC13W3F10000-50-799.0 85045GAEPT CBC13W3M1F00C-50 85045GAEST CBC13W3F1F00C-50 85045GAEPR CBC13W3M1000C-50 85045GAESR CBC13W3F1000C-50 85045GBEPT DBMMY13W3PA101 P133PSA2D CBC13W3M02F00C-0 PBMMHW13W3P 85045GBEST DBMMY13W3SA101 P133RSA2D CBC13W3F02F00C-0 PBMMHW13W3S 85045GBEPR DBMM13W3PA101 P13

18、3PSA2 CBC13W3M02000C-0 PBMMW13W3P 85045GBESR DBMM13W3SA101 P133RSA2 CBC13W3F02000C-0 PBMMW13W3P 85045NAEPT CBC13W3M1F00C-50-403.0 85045NAEST CBC13W3F1F00C-50-403.0 85045NAEPR CBC13W3M1000C-50-403.0 85045NAESR CBC13W3F1000C-50-403.0 85045MAEPT CBC13W3M1F000-50-403.4 85045MAEST CBC13W3F1F000-50-403.4

19、85045MAEPR CBC13W3M10000-50-403.3 85045MAESR CBC13W3F10000-50-403.3 1/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full complement of signal co

20、ntacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061. 6/ Pins 85045GAEP, 85045GAES, 85045GBEP, and 850450GBES are canceled and superseded by 85045GAEPT, 85045GAEST, 85045GBEPT, and 85045GB

21、EST respectively. 037Z3 85045 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name number and address 28198 Positronics Industries, Incorpo

22、rated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 85045 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVE PAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-