DLA DSCC-DWG-85062 REV D-2012 CONNECTOR ELECTRICAL MINIATURE RETAINER SLIDING LOCK.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Adding new parts; vendor CAGE 71785. 88-03-16 R Marbias B Page 4, Revised marking paragraph. Added caution note. 92-06-10 James P. Donohue C Update to new DSCC Drawing format. Remove AQL and replace with C=O. Editorial changes throughout. Deleted vendor CAGE

2、 71785. 01-06-29 Robert M. Heber D Page 1, added DLA Land and Maritime note. Replace MIL-STD-100 with ASME standards and made this a source control drawing. Change figure 1 dimension A in PIN -05 of page 2. Added new PIN -08 to page 2 and 5. Added new hardware material and finish in page 4. Added ma

3、rking note for tag and bag parts in page 5. Editorial changes throughout. 12-09-26 Abdo Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV D D C D D PAGE 1 2 3 4 5 PMIC A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 Denni

4、s L. Kelly Original date of drawing 8 May 1986 CHECKED BY TITLE L. V. Olszewski CONNECTOR, ELECTRICAL, MINIATURE, RETAINER, SLIDING LOCK APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 85062 A 037Z3 REV D PAGE 1 OF 5 AMSC N/A 5935-E846-001 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAME

5、S TO: DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 85062 REV D PAGE 2 Items DSCC drawing Part or Identifying Numbe

6、r (PIN) Dimensions in inches A B C Retainer 85062-01 1.720 .500 1.312 Retainer 85062-02 2.260 .500 1.852 Retainer 85062-03 2.908 .500 2.500 Retainer 85062-04 2.814 .609 2.406 Retainer 85062-05 1.380 .500 .984 Post 85062-06 Steel Post 85062-07 Non-magnetic (brass) Post 85062-08 Corrosion resistant st

7、eel Inches mm Inches mm .005 .015 .112 .144 .500 .609 .984 1.312 0.13 0.38 2.84 3.66 12.70 15.47 24.99 33.32 1.380 1.720 1.852 2.260 2.406 2.500 2.814 2.908 35.05 43.69 47.04 57.40 61.11 63.50 71.48 73.86 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information onl

8、y. 3. The two screws come with the sliding lock package. 4. Order additional lock posts as required. 5. Unless otherwise specified, tolerance is .015 (0.38 mm). FIGURE 1. Retainer, sliding lock. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

9、 SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 85062 REV C PAGE 3 Inches mm .015 .102 .112 .416 0.38 2.59 2.84 10.57 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. The two screws come with the sliding lock package

10、. 4. Order additional lock posts as required. 5. Unless otherwise specified, tolerance is .015 (0.38 mm). FIGURE 2. Post, sliding lock. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE

11、CODE DWG NO. A 037Z3 85062 REV D PAGE 4 ENGINEERING DATA: Description: Accessory for subminiature rectangular connector. Material: Retainer plate: Corrosion resisting steel. Hardware: Cold rolled steel, non-magnetic (brass), or corrosion resistant steel. Finish: Retainer plate: Passivated. Hardware:

12、 Cadmium plate, yellow chromate, trivalent chromate over zinc, or passivated. Outline drawing: See figures 1 and 2. Marking: The item shall be marked with the DSCC PIN and the manufacturers CAGE code and name in accordance with the basic requirements of MIL-STD-1285. Individual parts need not be mar

13、ked. If not marked, the marking information will be applied to a tag, and the tag will be supplied in a bag with the parts. Workmanship: The item shall be manufactured in such a manner as to be uniform in quality and shall be free from defects that may adversely affect the intended function of the i

14、tem in its intended application. Lot conformance testing: The manufacturer shall be responsible for assuring compliance to all the requirements of this drawing. Samples shall be selected in accordance with table I. If one or more defects are found, the lot shall be screened for that particular defec

15、t and defects removed. A new sample of parts shall be selected in accordance with table I and tested to the requirements of this drawing. If one or more defects are found in the second sample, the lot shall be rejected and shall not be supplied to this specification. TABLE I. Lot and sample size. Lo

16、t size Sample size 2 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1,200 1,201 to 3,200 3,201 to 10,000 10,001 and over 3 5 6 7 10 11 15 18 22 29 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBU

17、S, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 85062 REV D PAGE 5 Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to

18、 DSCC-VAI. DSCC drawing PIN Vendor similar PIN 1/ CAGE 71468 85062-01 DA51220-1 85062-02 DB51221-1 85062-03 DC51222-1 85062-04 DD51223-1 85062-05 DE51224-1 85062-06 D53018 85062-07 D53018-5 85062-08 D53018-14 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vender CAGE Vendor name number and address 71468 ITT Cannon P.O. Box 929 666 Dyer Road Santa Ana, CA 92702 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-