DLA DSCC-DWG-85067 REV C-2004 HOLDER ELECTRICAL CARD CARD GUIDE NON-CONDUCTIVE PLASTIC ANTIVIBRATION《减振非导电塑料的插件导轨电卡座》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add 3 more part. Add 3 material parameters. 17 DEC 1986 IRJ B Change FSC from 5999 to 5998. Editorial changes throughout. - bjm 18 OCT 2000 Thomas M. Hess C Added additional suggested source of supply. Editorial changes throughout. 17 SEP 2004 Thomas M. Hes

2、s THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV C C C C C C C C REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000

3、Original date of drawing 11 September 1985 CHECKED BY Dan McGrath TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Ivan R Jones NON-CONDUCTIVE PLASTIC, ANTI-VIBRATION SIZE A CODE IDENT. NO. 14933 DWG NO. 85067 REV C PAGE 1 OF 8 AMSC N/A 5998-E052 DISTRIBUTION STATEMENT A. Approved for public r

4、elease; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/programs/milspec/docsearch.asp Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

5、IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of card holders intended to hold printed circuit boards and circuit card assemblies that are .050 to .100 inch thick.

6、 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85067 Drawing number -01 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this

7、 document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at

8、 http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless

9、otherwise specified, the issues of the documents are those cited in the solicitation or contract (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM D3935 - Polycarbonate (PC) Unfilled and Reinforced Material. (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor

10、Drive, West Conshohocken, PA 19428-2959 or at URL http:/www.astm.org.) (Non-Government Standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational

11、services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. P

12、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensi

13、ons shall be as specified on figures 1, 2, 3, table I, and herein. 3.2 Material. Material shall be polycarbonate in accordance with ASTM D3935. 3.3 Dielectric strength. The dielectric strength shall be 400 volts per .001 inch minimum. 3.4 Tensile yield strength. The tensile yield strength shall be 8

14、,000 pounds per square inch minimum. 3.5 Flexural strength. The flexural strength shall be 11,000 pounds per square inch minimum. NOTES: 1. Dimensions are in inches. (See table II for metric equivalents.) 2. See table I for “A”, “B”, “H”, and “L” dimensions and tolerances. FIGURE 1. Three mounting b

15、utton design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 4 NOTES: 1. Dimensions are in inches. (See table II for metric equivalent

16、s.) 2. See table I for “A”, “B”, “H”, and “L” dimensions and tolerances. FIGURE 2. Two mounting button design and dimensions. NOTES: 1. Dimensions are in inches. (See table II for metric equivalents.) 2. See table I for “A”, “B”, “C”, “H”, and “L” dimensions and tolerances. FIGURE 3. Rivet or bolt m

17、ounting design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 5 TABLE I. Dimensions of card holders DSCC PIN 85067- Figure Mounting b

18、utton hole diameter (+.003 to -.000) Dim. “L” Dim. “H” Dim. “A” Dim. “B” Dim “C” Number of cantilevered grips 01 1 .130 7.000 .218 6.500 .087 N/A 4 02 2 .191 6.875 .218 6.375 .087 N/A 5 03 3 N/A 6.375 .185 5.980 .087 See note 4 5 04 2 .130 5.500 .220 5.000 .087 N/A 4 05 2 .130 4.125 .220 3.625 .073

19、N/A 3 06 2 .130 4.125 .180 3.625 .087 N/A 3 07 2 .130 3.500 .180 3.000 .065 N/A 2 08 2 .130 2.500 .180 2.200 .087 N/A 2 09 2 .130 2.500 .270 2.200 .100 N/A 2 10 3 N/A 4.125 .180 3.625 .087 See note 5 3 11 3 N/A 3.500 .180 3.000 .065 See note 6 2 12 3 N/A 2.500 .180 2.200 .087 See note 5 2 NOTES: 1.

20、Dimensions are in inches. (See table II for metric equivalents.) 2. Unless otherwise specified, tolerances for all dimensions under 6” .010, 6” and over .020. 3. Mounting panel thickness shall be .060/.070 inch for PINs 01, 02, 04 through 09. 4. .128 inch diameter holes counter bore .370 inch diamet

21、er, .040 inch deep (2 places). 5. .128 inch diameter holes counter bore .290 inch diameter, .030 inch deep (2 places). 6. .125 inch diameter holes counter bore .290 inch diameter, .030 inch deep (2 places). TABLE II. Metric equivalents. Inches Metric Inches Metric Inches Metric Inches Metric .010 0.

22、254 .087 2.210 .220 5.588 3.625 92.075 .020 0.508 .100 2.540 .270 6.858 4.125 104.775 .030 0.762 .125 3.175 .290 7.366 5.000 127.000 .040 1.016 .128 3.251 .370 9.398 5.500 139.700 .050 1.270 .130 3.302 .469 11.913 5.980 151.892 .060 1.524 .180 4.572 2.200 55.880 6.375 161.925 .065 1.651 .185 4.699 2

23、.500 63.500 6.500 165.100 .070 1.778 .191 4.851 3.000 76.200 6.875 174.625 .073 1.854 .218 5.537 3.500 88.900 7.000 177.800 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG

24、 NO. 85067 REV C PAGE 6 3.6 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.7 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 a

25、nd include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum e

26、xtent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Workmanship. Card guides shall be free of flash, pits, voids, and excessive mold marks. Visible parting line is acceptable. 4. VERIFIC

27、ATION 4.1 Conformance inspections. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.9). Criteria for defects are listed in 4.1.5.

28、 4.1.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with tab

29、le III, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.1.5. 4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective p

30、arts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table III, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots w

31、hich are acceptable shall be clearly identified as reinspected lots. TABLE III. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,001 29 35 35,001

32、and over 29 40 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 7 4.1.5 Defective characteristics and properties. Dimensional characteristics are consi

33、dered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, o

34、r environmental survival of the part. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to conta

35、ct the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments system command. Packaging data retrieval is availab

36、le from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use.

37、Card holders conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.1.1 Environmentally preferable material. Environmentally preferable materials should

38、be used to the maximum extent possible that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. Table IV lists the Environmental Protection Agency (EPA) top seventeen hazardous materials targeted for major usage reducti

39、on. If any of these hazardous materials are required, it is recommended that it be used only when other materials cannot meet performance requirements. TABLE IV. EPA top seventeen hazardous materials. Benzene Dichloromethane Tetrachloroethylene Cadmium and Compounds Lead and Compounds Toluene Carbon

40、 Tetrachloride Mercury and Compounds 1,1,1 - Trichloroethane Chloroform Methyl Ethyle Ketone Trichloroethylene Chromium and Compounds Methyl Isobutyl Ketone Xylenes Cyanide and Compounds Nickel and Compounds 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete

41、PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this

42、document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43218

43、-3990 or by electronic mail at “5998_Documentsdscc.dla.mil” or by facsimile (614) 693-1642 or DSN 850-6939. 6.4 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact: D

44、efense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43218-3990 or by electronic mail “5998_Documentsdscc.dla.mil” or by facsimile (614) 693-1642 or DSN 850-6939. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE E

45、LECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85067 REV C PAGE 8 DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 85067-01 85067-02 85067-03 85067-04 85067-05 85067-06 85067-07 85067-08 85067-09 85067-10 85067-11 85067-12 R

46、AD7000 RAD6875 WEL6375 RAD5500 RAD4125 58-30-40 SPC3000 2500-38 2500-38-4 58-30-40CB SPC3000CB 2500-38CB 07556 UNITRACK Industries Inc. 967 E. Masten Circle Millford, DE 19963-1085 Phone: (302) 424-5050 Facsimile: (302) 424-5055 E-mail: URL: http:/ 1/ CAUTION: Do not use this number for item acquis

47、ition. Items acquired to this number may not satisfy the performance requirements of this drawing. DSCC drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 85067-01 85067-02 85067-04 85067-05 85067-07 CGF50-70 CGF50-69 CGF50-55 CGF50-42 CGF50-35 53507 Airquip

48、 Robleyco (A division of Micro Dimensional Products, Inc.) 199 West Spruce Street Norristown, PA 19401-3863 Phone: (610) 239-7990 Facsimile: (610) 239-7980 E-mail: URL: http:/ 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-