DLA DSCC-DWG-85068 REV A-2002 HOLDER ELECTRICAL CARD CARD GUIDE PLASTIC FASTENER MOUNTED《紧固件塑胶插件导轨电卡座》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Change FSC from 5999 to 5998. Added 4 new devices. Editorial changes throughout. 21 Dec 2002 Thomas M. Hess Prepared in accordance with ASMEY14.100 Selected item drawing REV PAGE REV PAGE REV STATUS REV A A A A A A A OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A PR

2、EPARED BY Dan McGrath DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 30 July 1985 CHECKED BY Randy Larson TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Ivan R Jones PLASTIC, FASTENER MOUNTED SIZE A CODE IDENT. NO. 14933 DWG NO. 85068 REV A P

3、AGE 1 OF 7 AMSC N/A 5998-E040 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitte

4、d without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of card guides intended for use with printed circuit boards and circuit card assemblies. 1.2 P

5、art or Identifying Number (PIN). The complete PIN shall be as follows: 85068 Drawing number 04 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this docume

6、nt to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). STANDARDS DEPARTMENT OF DEFENSE MILSTD12

7、85 Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Defense Automated Printing Service, Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Governmen

8、t publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of document

9、s not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM D4066 Nylon Injection and Extrusion Materials (PA). (Application for copies should be addressed to the ASTM International, 100 Barr Harbor Drive, West Coshohocken, PA 19428-

10、2959.) (Non-Government Standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict b

11、etween the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permit

12、ted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified on figure 1 and in table I. 3.2 Materi

13、al. Material shall be nylon in accordance with ASTM D4066 (for parts 01 through 03) or polycarbonate (for parts 04 through 07). FIGURE 1. Dimensions and configuration. FIGURE 2. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

14、S-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAGE 4 FIGURE 3. Dimensions and configuration. TABLE I. Dimensions of card holders Dimensions 1/ 2/ PIN 85068 Figure A .030 (0.76) B .010 (0.25) C .030 (0.76) D E F G H J K 01 1 2.000 (50.80) 1.750 (

15、44.45) 1.500 (38.10) .230 (5.84) .125 (3.18) .062 (1.57) .081 (2.06) .150 (3.81) .210 (5.33) .063 (1.60) 02 1 3.500 (88.90) 3.250 (82.55) 3.000 (76.20) .230 (5.84) .125 (3.18) .062 (1.57) .095 (2.41) .185 (4.70) .210 (5.33) .063 (1.60) 03 1 5.000 (127.00) 4.750 (120.65) 4.500 (114.30) .230 (5.84) .1

16、25 (3.18) .062 (1.57) .095 (2.41) .185 (4.70) .210 (5.33) .063 (1.60) 04 2 3.50 (88.9) 3.00 (76.2) .38 (9.7) .07 (1.8) .128 (3.25) .290 (7.37) .11 (2.8) .070 (1.78) 05 2 6.875 (174.6) 6.375 (161.9) .38 (9.7) .07 (1.8) .128 (3.25) .290 (7.37) .11 (2.8) .070 (1.78) 06 3 8.50 (215.9) 8.00 (203.2) 4.00

17、(101.6) .38 (9.7) .07 (1.8) .128 (3.25) .290 (7.37) .11 (2.8) .070 (1.78) 07 3 8.50 (215.9) 8.00 (203.2) 4.00 (101.6) .38 (9.7) .07 (1.8) .128 (3.25) .290 (7.37) .11 (2.8) .100 (2.54) NOTES: 1. Dimensions are in inches. Metric equivalents (in parenthesis) are given for information only. 2. Unless ot

18、herwise specified, tolerance is .010 inch (0.25 mm) for two place decimals and .005 (0.25 mm) for three place decimals. 3.3 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.4 Marking. Marking of the card hold

19、er is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.5 Workmanship. Card guides shall be free of flash, pits, voi

20、ds, and excessive mold marks. Visible parting line is acceptable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAGE 5 4. VERIFICATION 4.1 Sampling and i

21、nspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the perfor

22、mance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4

23、.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.5). Criteria for defects are listed in 4.2.5. 4.2.2

24、Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.c). 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table 3, n

25、ormal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.2.5. TABLE 3. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,20

26、1 to 10,000 22 29 10,001 and over 29 35 4.2.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a ran

27、dom sample of parts in accordance with table III, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.2.5 Defective cha

28、racteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they wou

29、ld be detrimental to the intended use, performance requirements, or environmental survival of the part. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAG

30、E 6 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requis

31、ite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is available from the managing Military Departments or De

32、fense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are int

33、ended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for deliver

34、y of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordina

35、ted only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at “5998.Docum

36、entsdscc.dla.mil” or by facsimile (614) 692-6939 or DSN 850-6939. 6.4 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact: Defense Supply Center, Columbus, ATTN: DSCC

37、-VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail “5998.Documentsdscc.dla.mil” or by facsimile (614) 692-6939 or DSN 850-6939. DSCC drawing PIN Vendor similar Designation or type number 1/ Vendor CAGE Vendor name and address 8506801 8506802 8506803 88272 88273 88275 2/ Aavid

38、Thermalloy LLC 80 Commercial Street Concord NH 03301 Phone: (603) 224-9988 Toll Free Phone: (800) 366-2843 Facsimile: (603) 223-1790 e-mail: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Parts

39、are no longer available from suggested source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85068 REV A PAGE 7 DSCC drawing PIN Vendor similar Designation

40、 or type number 1/ Vendor CAGE Vendor name and address 8506804 8506805 8506806 8506807 PRD3500 PRD6875 PRD8500 PRD8500B 07556 UNITRACK Industries Inc. 967 East Masten Circle Millford, DE 19963-1085 TEL: (302) 424-5050 FAX: (302) 424-5055 E-MAIL: URL: 1/ CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-