DLA DSCC-DWG-85076 REV B-2003 HOLDER ELECTRICAL CARD CARD GUIDE PLASTIC《塑胶的 有插件导轨的电卡座》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add irridite finish reference to MIL-C-5541. Change threads to stainless steel inserts. 5 AUG 1988 Randy Larson B Replaced canceled documents. Editorial changes throughout. 31 DEC 2003 Thomas M. Hess Prepared in accordance with ASME Y14.100 Selected item dr

2、awing REV PAGE REV B B PAGE 17 18 REV STATUS REV B B B B B B B B B B B B B B B B OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A PREPARED BY Chris Rauch DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 http:/www.dscc.dla.mil Original date of drawing 24 September

3、 1985 CHECKED BY Randy Larson TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Ivan R. Jones PLASTIC SIZE A CODE IDENT. NO. 14933 DWG NO. 85076 REV B PAGE 1 OF 18 AMSC N/A 5998-E044 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CO

4、DE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 2 1. SCOPE

5、1.1 Scope. This drawing describes the requirements for a family of card guides intended for use with circuit card assemblies. These card guides are designed to be used with DSCC drawing 85075 mounting bars and DSCC Drawing 85036 spacers. 1.2 Part or Identifying Number (PIN). The complete PIN shall b

6、e as follows: 85076 Drawing number 001 Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended

7、for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Govern

8、ment documents. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-S-5002 Surface Treat

9、ments and Inorganic Coatings for Metal Surfaces of Weapon Systems. DEPARTMENT OF DEFENSE STANDARDS MILSTD1285 Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Docum

10、ent Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract

11、. ASTM INTERNATIONAL (ASTM) ASTM A484 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings. ASTM A582 - Standard Specification for Free-Machining Stainless Steel Bars. ASTM D4066 - Standard Specification for Nylon Injection and Extrusion Materials (PA). (

12、Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, P.O. Box C700, West Coshohocken, PA 19428-2959 or at URL: http:/www.astm.org.) (Non-Government standards and other publications are normally available from the organizations which prepare or whi

13、ch distribute the documents. These documents also may be available in or through libraries or other informational services. They are also distributed among technical groups and using Federal agencies.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

14、DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 3 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however,

15、supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified in table I and figure 1. 3.2 Materials. The card guide material shall be type 66 ny

16、lon in accordance with ASTM D4066. The insert material, when required, shall be stainless steel type 303 in accordance with ASTM A484 or ASTM A582. 3.3 Finish. The insert, when stainless steel, shall be passivated in accordance with MIL-S-5002. 3.4 Certificate of compliance. A certificate of complia

17、nce shall be required from manufacturers requesting to be a suggested source of supply. 3.4.1 Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer a statement of compliance in lieu of the manufacturer performing the inspecti

18、on of product for delivery tests (see 4.1.2 and 6.2.b). 3.5 Marking. Marking of the card guide is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CA

19、GE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and pro

20、motes economically advantageous life cycle costs. 3.7 Workmanship. Card guides shall be free of flash, pits, voids, cracks, and excessive mold marks. A visible parting line is acceptable. 4. VERIFICATION 4.1 Conformance inspections. 4.1.1 Inspection of product for delivery. Inspection of product for

21、 delivery shall consist of visual and mechanical inspections of design and dimensions (see 3.1), materials (see 3.2), finish (see 3.3), and workmanship (see 3.7). Criteria for defects are listed in 4.1.5. 4.1.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a

22、 statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria fo

23、r defects are listed in 4.1.5. 4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sampl

24、e of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.1.5 Defective characteristi

25、cs and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detr

26、imental to the intended use, performance requirements, or environmental survival of the part. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 4 Config

27、uration A (single piece card guide) Configuration B (single piece with foot) FIGURE 1. Dimension and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 850

28、76 REV B PAGE 5 Configuration C (interlocking front/rear piece) Configuration D (interlocking center piece) FIGURE 1. Dimension and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHI

29、O SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 6 Configuration E (interlocking with foot) Inches nm Inches mm Inches mm Inches mm Inches mm .075 .107 .120 1.91 2.70 3.05 .187 .250 .265 4.75 6.35 6.73 .300 .375 .437 7.62 9.53 11.10 .500 .625 .750 12.70 15.88 19.05 .875 1.062 22.23 26.98 NOTES

30、: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 inch (0.25 mm) for three place decimals, .02 (0.5 mm) for two place decimals, and .004 per inch (0.10 mm) for length only. 4. For all foot configurations (B

31、 and E), dimension C is as follows: When B dimension is C dimension is .157 (3.99 mm) through .437 (11.09 mm) Not applicable .515 (13.08 mm) or .594 (15.09 mm) .375 (9.53 mm) .672 (17.07 mm) .500 (12.7 mm) .937 (23.79 mm) .750 (19.05 mm) 5. These dimensions molded to fit DSCC Drawing 85075 support m

32、ounting bars. 6. At manufacturers option, ends of card slot may be either straight or beveled. 7. Tapered flange optional at manufacturers discretion. FIGURE 1. Dimension and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DE

33、FENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 7 TABLE I. Length dimensions. 1/ 2/ Pin 85076 Dimension “A” Dimension “B” PIN 85076 Dimension “A” Dimension “B” Configuration A Configuration A 001 2.750 (69.85) 008 5.125 (130.18) 002 2.940 (74.68) 009

34、 6.000 (152.40) 003 3.437 (87.30) 010 6.500 (165.10) 004 3.875 (98.43) 011 7.000 (177.80) 005 4.187 (106.35) 012 7.500 (190.50) 006 4.300 (109.22) 013 7.750 (196.85) 007 4.750 (120.65) Configuration B Configuration B 014 .157 (3.99) 047 .374 (9.50) 015 .203 (5.16) 048 .391 (9.93) 016 .253 (6.43) 049

35、 .437 (11.10) 017 .374 (9.50) 050 .515 (13.08) 018 .391 (9.93) 051 .594 (15.09) 019 .437 (11.10) 052 .672 (17.07) 020 .515 (13.08) 053 3.875 (98.43) .937 (23.80) 021 .594 (15.09) 054 .157 (3.99) 022 .672 (17.07) 055 .203 (5.16) 023 2.750 (69.85) .937 (23.80) 056 .253 (6.43) 024 .157 (3.99) 057 .374

36、(9.50) 025 .203 (5.16) 058 .391 (9.93) 026 .253 (6.43) 059 .437 (11.10) 027 .374 (9.50) 060 .515 (13.08) 028 .391 (9.93) 061 .594 (15.09) 029 .437 (11.10) 062 .672 (17.07) 030 .515 (13.08) 063 4.187 (106.35) .937 (23.80) 031 .594 (15.09) 064 .157 (3.99) 032 .672 (17.07) 065 .203 (5.16) 033 2.940 (74

37、.68) .937 (23.80) 066 .253 (6.43) 034 .157 (3.99) 067 .374 (9.50) 035 .203 (5.16) 068 .391 (9.93) 036 .253 (6.43) 069 .437 (11.10) 037 .374 (9.50) 070 .515 (13.08) 038 .391 (9.93) 071 .594 (15.09) 039 .437 (11.10) 072 .672 (17.07) 040 .515 (13.08) 073 4.300 (109.22) .937 (23.80) 041 .594 (15.09) 074

38、 .157 (3.99) 042 .672 (17.07) 075 .203 (5.16) 043 3.437 (87.30) .937 (23.80) 076 .253 (6.43) 044 .157 (3.99) 077 .374 (9.50) 045 .203 (5.16) 078 .391 (9.93) 046 3.875 (98.43) .253 (6.43) 079 4.750 (120.65) .437 (11.10) See notes at end of table. Provided by IHSNot for ResaleNo reproduction or networ

39、king permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 8 TABLE I. Length dimensions Continued. 1/ 2/ Pin 85076 Dimension “A” Dimension “B” PIN 85076 Dimension “A” Dimension “B” Configuration B Configuration B 08

40、0 .515 (13.08) 112 .672 (17.07) 081 .594 (15.09) 113 6.500 (165.10) .937 (23.80) 082 .672 (17.07) 114 .157 (3.99) 083 4.750 (120.65) .937 (23.80) 115 .203 (5.16) 084 .157 (3.99) 116 .253 (6.43) 085 .203 (5.16) 117 .374 (9.50) 086 .253 (6.43) 118 .391 (9.93) 087 .374 (9.50) 119 .437 (11.10) 088 .391

41、(9.93) 120 .515 (13.08) 089 .437 (11.10) 121 .594 (15.09) 090 .515 (13.08) 122 .672 (17.07) 091 .594 (15.09) 123 7.000 (177.80) .937 (23.80) 092 .672 (17.07) 124 .157 (3.99) 093 5.125 (130.18) .937 (23.80) 125 .203 (5.16) 094 .157 (3.99) 126 .253 (6.43) 095 .203 (5.16) 127 .374 (9.50) 096 .253 (6.43

42、) 128 .391 (9.93) 097 .374 (9.50) 129 .437 (11.10) 098 .391 (9.93) 130 .515 (13.08) 099 .437 (11.10) 131 .594 (15.09) 100 .515 (13.08) 132 .672 (17.07) 101 .594 (15.09) 133 7.500 (190.50) .937 (23.80) 102 .672 (17.07) 134 .157 (3.99) 103 6.000 (152.40) .937 (23.80) 135 .203 (5.16) 104 .157 (3.99) 13

43、6 .253 (6.43) 105 .203 (5.16) 137 .374 (9.50) 106 .253 (6.43) 138 .391 (9.93) 107 .374 (9.50) 139 .437 (11.10) 108 .391 (9.93) 140 .515 (13.08) 109 .437 (11.10) 141 .594 (15.09) 110 .515 (13.08) 142 .672 (17.07) 111 6.500 (165.10) .594 (15.09) 143 7.750 (196.85) .937 (23.80) Configuration C Configur

44、ation C 144 2.750 (69.85) 150 4.750 (120.65) 145 2.940 (74.68) 151 5.125 (130.18) 146 3.437 (87.30) 152 6.000 (152.40) 147 3.875 (98.43) 153 6.500 (165.10) 148 4.187 (106.35) 154 7.000 (177.80) 149 4.300 (109.22) 155 7.500 (190.50) See notes at end of table. Provided by IHSNot for ResaleNo reproduct

45、ion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85076 REV B PAGE 9 TABLE I. Length dimensions Continued. 1/ 2/ Pin 85076 Dimension “A” Dimension “B” PIN 85076 Dimension “A” Dimension “B” Configuration D Confi

46、guration D 156 2.750 69.85 160 4.187 (106.35) 157 2.940 74.68 161 4.300 (109.22) 158 3.437 87.30 162 4.750 (120.65) 159 3.875 98.43 163 6.000 (152.40) Configuration E Configuration E 164 .157 (3.99) 200 .515 (13.08) 165 .203 (5.16) 201 .594 (15.09) 166 .253 (6.43) 202 .672 (17.07) 167 .374 (9.50) 20

47、3 3.875 (98.43) .937 (23.80) 168 .391 (9.93) 204 .157 (3.99) 169 .437 (11.10) 205 .203 (5.16) 170 .515 (13.08) 206 .253 (6.43) 171 .594 (15.09) 207 .374 (9.50) 172 .672 (17.07) 208 .391 (9.93) 173 2.750 (69.85) .937 (23.80) 209 .437 (11.10) 174 .157 (3.99) 210 .515 (13.08) 175 .203 (5.16) 211 .594 (

48、15.09) 176 .253 (6.43) 212 .672 (17.07) 177 .374 (9.50) 213 4.187 (106.35) .937 (23.80) 178 .391 (9.93) 214 .157 (3.99) 179 .437 (11.10) 215 .203 (5.16) 180 .515 (13.08) 216 .253 (6.43) 181 .594 (15.09) 217 .374 (9.50) 182 .672 (17.07) 218 .391 (9.93) 183 2.940 (74.68) .937 (23.80) 219 .437 (11.10) 184 .157 (3.99) 220 .515 (13.08) 185 .203 (5.16) 221 .594