DLA DSCC-DWG-86024 REV B-2000 CONNECTORS ELECTRICAL TEST POINT TYPE PRINTED WIRING TYPE SINGLE TEST POINT 040《0 040单测点印刷线路型试点型电气连接器》.pdf

1、REVISIONS _ LTR 1 DESCRIPTION DATE APPROVED A 6 Add source 98291. 21 August 1986 R. Ma9ais Dimension changes to drawing, remove obsolete Military changes throughout. / Specifications, and removed source CAGE 98291. Editorial /P/fi/O distribution is unlimited. 5935-E639 Provided by IHSNot for ResaleN

2、o reproduction or networking permitted without license from IHS-,-,-Inches mm .O01 0.03 .O10 0.25 .O30 0.76 .O40 1.02 .O50 1.27 .O73 1.85 Inches mm .O75 1.91 .O80 2.03 .O92 2.34 .lo2 2.59 .I40 3.56 .185 4.70 NOTES 1. Dimensions are in inches. 2. Metric equivalents are given for general information o

3、nly. 3. Unless otherwise specified tolerance is 1.005 inches (0.13 mm). FIGURE 1. Physical dimensions. CAGE CODE DWG NO. 03723 86024 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. SCOPE 1.

4、1 Scope. This drawing covers the general requirements for a printed wiring board, single test point. 1.2 Part or Identifvinq Number (PIN). The complete PIN shall be as specified on the requirements drawing and constructed using the following format: DSCC zt drawing Dash number number 2. APPLICABLE D

5、OCUMENTS 2.1 Government Document. 2.1 .I Specifications. standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Depart

6、ment of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATION DEPARTMENTOFDEFENSE MIL-C-39024 - Connectors, Electrical, Jack, Tip (Test Point, Panel or Printed Wiring Type), General Specification For. STANDARD DEPARTMENT OF

7、DEFENSE MIL-STD-130 - Identification Marking of US. Military Property. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Defense Printing Service, Detachment Office, Building 4D, Customer Service, 700 Robbins Avenue, Philadelphia, PA 191

8、 11-5094). 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issue of the documents which are DOD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specif

9、ied, the documents not listed in the DoDISS are the issues of the document cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM BI6 ASTM B488 - - Rod, Brass, Free Cutting, Bar and Shapes for use in Screw Machines. Standard Specification for Electrodeposited Coa

10、tings of Gold for Engineering Uses. (Applications for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187). CAGE CODE DWG NO. 03723 86024 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4321 6-5000 Provided by IHSNot for ResaleNo

11、 reproduction or networking permitted without license from IHS-,-,-3. REQUIREMENTS 3.1 DSCC reauirements drawinq. The individual item requirements shall be in accordance with MIL-C-39024 except as specified herein. In case of conflict between this drawing and the requirements drawing, the latter sha

12、ll govern. 3.2 Desian, construction, and uhvsical dimensions. The design, construction, and physical dimensions shall be as specified on figure 1. 3.3 Material and finish. 3.3.1 m. Brass in accordance with ASTM B16, composition optional, gold plate in accordance with ASTM 8488, type 2, code optional

13、, thickness O. 50pm (20 microinches) over 100 microinches (0.003 mm) minimum nickel. 3.3.2 Surina contact. Beryllium copper, gold plate per body except thickness 1.25pm (50 microinches). 3.4 Desian characteristics. 3.4.1 Current ratinq. 5 amperes. 3.4.2 Board thickness. .O60 to .125 inches (1.52 to

14、1.96 mm). 3.4.3 Mountina hole. .075/.077 inches (1.91/1.96 mm) diameter. 3.5 Markinq. The manufacturers name (or symbol) and PIN in accordance with 1.2 herein shall be legibly marked on each package in accordance with MIL-STD-130. 4. QUALITY ASSURANCE PROVISIONS 4.1 Qualification insuection. Qualifi

15、cation inspection for contacts specified in this document are not required. 5. PACKAGING 5.1 Packaaina requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, t

16、hese personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Department or Defense Age

17、ncys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES 6.1 Intended use. Test points conforming to this drawing are intended for use when Military Specifications do not exist and qualified military test points that will perform the required fun

18、ction are not available for OEM applications. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a Military Specification exists and the product covered by this drawing has been qualified for listing o

19、n QPL-39024, this drawing will be inactivated and will not be used for new design. The QPL-39024 product shall be the preferred item for all applications. 6.2 Acquisition reauirements. The acquisition document should specify the following: a. Complete PIN (see 1.2). b. Requirements for certificate o

20、f compliance, if applicable (see 6.4). c. Requirements for packaging and packing (see 5.1). 6.3 Comments. Comments on this drawing should be directed to Defense Supply Center Columbus, P.O. Box 3990, Attn: VAI, Columbus, Ohio 4321 6-5000 or telephone (61 4) 692-0573, facsimile (61 4) 692-6940. 6.4 C

21、ertificate of compliance. The certificate of compliance submitted to DSCC-VAI, prior to listing as an approved source of supply, shall state that the manufacturers product meets the requirements of the applicable DSCC requirements drawing and as stated herein. CAGE CODE DWG NO. A DEFENSE SUPPLY CENT

22、ER, COLUMBUS COLUMBUS, OH 43216-5000 I B I PAGE 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Vendor CAGE number DSCC drawing Vendor PIN CAGE number 86024-1 1831 O 1831 O Vendor similar PIN I/ 09-9006-1 -035 Vendor name and address 03723 REV B A Concord Electronics Corporation 30 Great Jones Street New York City, N.Y. 10012-1 115 86024 PAGE 5 I CAGECODE I DWG No. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-