DLA DSCC-DWG-86094 REV F-2008 CIRCUIT BREAKERS MAGNETIC ILLUMINATED ROCKER TYPE AUXILIARY CONTACTS TRIP-FREE SERIES TRIP SINGLE POLE (0 05 TO 20 0 AMPERES)《单极串联跳闸辅助触点自动跳闸发光跷板式磁式断路器.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changed voltage requirements in 3.2 and added table IV. Editorial changes throughout. 10 NOV 1986 Randy Larson B Added horizontal marking to figure 1. 8 APR 1987 Randy Larson C Added wire leads and auxiliary contacts to figure 1. Added electrical requiremen

2、ts for auxiliary contacts and wire lead requirements to section 3. Updated vendor address. 23 AUG 1990 Randy Larson D Update document references, replace 6.4. 5 JUN 2000 Kendall Cottongim E Delete P/N and substitute PIN, editorial changes, update to latest DSCC DWG format. 19 JUN 2003 Kendall Cotton

3、gim F Update to latest DSCC DWG format. 3 MAR 2008 Michael Radecki THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV F F F F F F F F F REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Tony J. Westph

4、al DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY David Corbett APPROVED BY Randy Larson TITLE CIRCUIT BREAKERS, MAGNETIC, ILLUMINATED ROCKER TYPE, AUXILIARY CONTACTS TRIP-FREE, SERIES TRIP, SINGLE POLE (0.05 TO 20.0 AMPERES) SIZE A CODE IDENT. NO. 14933 DWG NO. 86

5、094 Original date of drawing 27 June 1986 REV F PAGE 1 OF 9 AMSC N/A 5925-E074CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DE

6、FENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of circuit breakers with illuminated handles for use in overcurrent protection. 1.2 Part or Identifying Number (PIN). The comple

7、te PIN is as follows: 86094- -001 B 1 I I I I I I I I Drawing number Dash number Color Handle (See table I) (See 3.10) (see 3.11) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents

8、 cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this spec

9、ification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those

10、 listed in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-39019 - Circuit Breakers, Magnetic, Low-Power, Sealed, Trip-Free, General Specification for. MIL-PRF-55629 - Circuit Breakers, Magnetic, Unsealed or Panel Seal, Trip Free, General Specification for. (Copies of these

11、 documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document

12、 and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The individual item requirements shall be

13、as specified herein and table I, table II, and table III. 3.2 Voltage and frequency rating. For dash numbers 001 through 038, the voltage and frequency rating shall be 50 V dc, maximum and 240 V ac, maximum at 60 or 400 Hz. For dash numbers 039 through 044, the voltage and frequency rating shall be

14、32 V dc, maximum and 120 V ac, maximum at 60 or 400 Hz. 3.3 Current rating. See table I. 3.4 Interface and physical dimension requirements. See figure 1 and table I. 3.5 Time delay. Time delay shall be in accordance with table I, table II, and table III. 3.6 Endurance. Endurance shall be in accordan

15、ce with MIL-PRF-39019. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 3 FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reprod

16、uction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance

17、is .030 (0.76 mm). FIGURE 1. Dimensions and configuration - Continued. Inches mm Inches mm .005 0.13 .695 17.65 .010 0.25 .710 18.03 .062 1.57 .920 23.37 .093 2.36 1.245 31.62 .125 3.18 1.250 31.75 .180 4.57 1.610 40.89 .250 6.35 1.770 44.96 .350 8.89 1.775 45.06 .490 12.45 1.810 45.97 .520 13.20 1.

18、850 46.99 .555 14.10 2.00 50.8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 5 TABLE I. Circuit breaker dash number and applicable characteristics. R

19、esistance or impedance (ohms - max) 2/ Resistance or impedance (ohms - max) 2/ P/N 86094 Current rating (amps) Time delay 1/ DC 60 Hz 400 Hz P/N 86094 Current rating (amps) Time delay 1/ DC 60 Hz 400 Hz 001 0.05 A 680.0 690.0 710.0 023 4.0 A 0.10 0.10 0.12 002 0.05 B 680.0 690.0 710.0 024 4.0 B 0.10

20、 0.10 0.12 003 0.1 A 150.0 170.0 180.0 025 5.0 A 0.061 0.063 0.072 004 0.1 B 150.0 170.0 180.0 026 5.0 B 0.061 0.063 0.072 005 0.25 A 20.0 26.0 27.0 027 6.0 A 0.042 0.043 0.050 006 0.25 B 20.0 26.0 27.0 028 6.0 B 0.042 0.043 0.050 007 0.5 A 5.4 6.0 6.6 029 7.0 A 0.036 0.036 0.040 008 0.5 B 5.4 6.0 6

21、.6 030 7.0 B 0.036 0.036 0.040 009 0.75 A 2.5 2.7 2.8 031 7.5 A 0.031 0.031 0.038 010 0.75 B 2.5 2.7 2.8 032 7.5 B 0.031 0.031 0.038 011 1.0 A 1.35 1.5 1.61 033 8.0 A 0.027 0.027 0.035 012 1.0 B 1.35 1.5 1.61 034 8.0 B 0.027 0.027 0.035 013 1.25 A 0.9 1.0 1.1 035 9.0 A 0.022 0.022 0.028 014 1.25 B 0

22、.9 1.0 1.1 036 9.0 B 0.022 0.022 0.028 015 1.5 A 0.65 0.70 0.75 037 10.0 A 0.018 0.021 0.024 016 1.5 B 0.65 0.70 0.75 038 10.0 B 0.018 0.021 0.024 017 2.0 A 0.40 0.40 0.50 039 12.5 A 0.012 0.013 0.015 018 2.0 B 0.40 0.40 0.50 040 12.5 B 0.012 0.013 0.015 019 2.5 A 0.25 0.25 0.27 041 15.0 A 0.009 0.0

23、09 0.010 020 2.5 B 0.25 0.25 0.27 042 15.0 B 0.009 0.009 0.010 021 3.0 A 0.15 0.15 0.17 043 20.0 A 0.006 0.006 0.007 022 3.0 B 0.15 0.15 0.17 044 20.0 B 0.006 0.006 0.007 1/ All dash numbers include inertial delay with the time delay. 2/ The corresponding maximum wattage losses, which in no case sha

24、ll exceed 3.0 watts, may be calculated as I2R or I2Z. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 6 TABLE II. Calibration tripping times (seconds)

25、at 25C 2C. Percent of rated current Time delay A (fast) Time delay B (slow) Min Max Min Max 100 No trip No trip No trip No trip 1 hour 1 hour 1 hour 1 hour 135 0.2 7.0 3.0 60.0 200 0.055 0.95 0.5 9.0 400 Inst 1/ 0.24 Inst 1/ 1.75 600 Inst 1/ 0.13 Inst 1/ 0.6 800 Inst 1/ 0.06 Inst 1/ 0.1 2/ 800 at 60

26、Hz 3/ No trip No trip No trip No trip 1,400 at 400 Hz 4/ No trip No trip No trip No trip 1/ (Inst) instantaneous is defined as less than 0.015 second. 2/ This time is extended to 0.3 second for dc and 400 Hz. 3/ 800 percent peak, one 1/2 sine pulse at 60 Hz. 4/ 1,400 percent peak, one 1/2 sine pulse

27、 at 400 Hz. TABLE III. High and low temperature tripping times (seconds). Time delay A (fast) Time delay B (slow) Percent of rated current -40C 2C +100C 2C -40C 2C +100C 2C Min Max Min Max 100 No trip No trip No trip No trip 1 hour 1 hour 1 hour 1 hour 135 400.0 0.10 500.0 0.4 150 800.0 - 1000.0 - 2

28、00 5.0 0.015 25.0 0.04 400 0.7 Inst 1/ 10.0 Inst 1/ 500 0.5 Inst 1/ 2.0 Inst 1/ 800 0.06 Inst 1/ 0.1 2/ Inst 1/ 800 at 60 Hz 3/ No trip No trip No trip No trip 1,400 at 400 Hz 4/ No trip No trip No trip No trip 1/ (Inst) instantaneous is defined as less than 0.015 second. 2/ This time is extended to

29、 0.3 second for dc and 400 Hz. 3/ 800 percent peak, one 1/2 sine pulse at 60 Hz. 4/ 1,400 percent peak, one 1/2 sine pulse at 400 Hz. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO.

30、14933 DWG NO. 86094 REV F PAGE 7 3.7 Resistance or impedance. See table I. 3.8 Interrupting capacity. Interrupting capacity shall be in accordance with MIL-PRF-39019. 3.9 Dielectric withstanding voltage. Dielectric withstanding voltage shall be in accordance with MIL-PRF-39019. 3.10 Color. The color

31、 of the circuit breaker shall be specified in the PIN according to the following designations: B-black, W-white, G-gray. 3.11 Handle. The handle of the circuit breaker shall be specified in the PIN according to the following designations: 1-white (neon illuminated, vertical marking), 2-white (red LE

32、D illuminated, vertical marking), 3-black (red LED illuminated, vertical marking), 4-white (neon illuminated, horizontal marking), 5-white (red LED illuminated, horizontal marking), 6-black (red LED illuminated, horizontal marking). 3.12 Vibration. Vibration shall be in accordance with MIL-PRF-55629

33、. 3.13 Shock. Shock shall be in accordance with MIL-PRF-55629. 3.14 Insulation resistance. Insulation resistance shall be in accordance with MIL-PRF-39019. 3.15 Auxiliary contacts. Auxiliary contacts shall be 5 amperes maximum at 250 V ac or 28 V dc. 3.16 Wire leads. The wire leads, used for handle

34、illumination, shall be stranded No. 28 AWG wires with a minimum length of 2.5 inches and a maximum diameter over the insulation of .065 inch. 3.17 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum

35、extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.18 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-

36、55629 Qualified Product List for at least one part, or perform the Group A inspection specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.19 Certificate of compliance. A certificate of compliance shall be required from a manufacturer requesting to be an approved sour

37、ce of supply. 3.20 Marking. Marking shall be as specified in MIL-PRF-55629, except the DSCC drawing PIN in accordance with 1.2 herein shall be used instead of the military part number. 3.21 Workmanship. Parts shall be free of flash pits, voids, and excessive mild marks. Visible parting line is accep

38、table. 4. VERIFICATION 4.1 Conformance inspection. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspections of MIL-PRF-55629. 4.1.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group A r

39、equirements in lieu of performing group A tests (see 6.2c). 4.1.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-55629. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHI

40、O SIZE A CODE IDENT NO. 14933 DWG NO. 86094 REV F PAGE 8 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel n

41、eed to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Service or Defense Agency, or within the military services system command. Packaging data retrieval is a

42、vailable from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended

43、use. Devices conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The acquisition document should specify the following: a. Complete P

44、IN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group A tests or provides certification of compliance with group A requirements. d. Requirements for notification of cha

45、nge of product to the contracting activity, if applicable. e. Requirements for packaging and packing. 6.3 Application information for illuminated handle. 6.3.1 Neon bulb. A neon bulb is provided when specified for 120 V ac and 250 V ac operation (see 1.2 and 3.11). For operation at 120 V ac, a 33,00

46、0-ohm, 1/2-watt external resistor is required. At 250 V ac, a 100,000-ohm, 1-watt external resistor is required. 6.3.2 Red LED. A LED with 750 feet lumens at 20 mA is provided in the center of the handle when specified (see 1.2 and 3.11). Maximum power dissipation at 25C is 180 mW. Continuous forwar

47、d current is 40 mA. Forward voltage, typical, is 1.6 volt at 20 mA. Reverse current, typical, is 100 nA at 3.0 volts. An external resistor; 1/2 watt minimum, will be required to limit current to these values. This external resistor will not be supplied by the circuit breaker manufacturer and should

48、be selected in accordance with table IV. TABLE IV. External resistor. Resistance value Operating voltage (dc) 270 4.0 to 7.9 820 8.0 to 15.9 1,500 16.0 to 23.9 2,700 24.0 to 32.0 6.4 Users of record. Coordination of this document for future revisions are coordinated only with the approved source(s)

49、of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:circuitprotectdla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0548 or DSN 850-0548. Provid