DLA DSCC-DWG-86097 REV E-2004 RESISTOR VARIABLE PANEL MOUNTED 1 WATT《1瓦特装在面板上的可变电阻器》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added ordering data. Editorial changes throughout. 5 JAN 87 D. MOORE B Added new dash numbers and new figure (with PC pins). Editorial changes throughout. 17 SEP 87 D. MOORE C Editorial changes throughout. 15 MAR 88 D. MOORE D Remove vendor and editorial ch

2、anges throughout 7 JAN 99 A. ERNST E Update and verification. Editorial changes throughout. 28 MAY 04 K. COTTONGIM CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with AMSE Y14.100 Selected item drawing

3、 REV PAGE REV STATUS OF PAGES REV E E E E E E E E E PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Allan R. Knox DEDIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing CHECKED BY David W. Withrow TITLE RESISTOR, VARIABLE, PANEL MOUNTED, 16 June 1986 APPROVED

4、 BY David W. Withrow 1 WATT SIZE A CODE IDENT. NO. 14933 DWG NO. 86097 REV E PAGE 1 OF 9 AMSC N/A 5905-E502 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E P

5、AGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 1 watt, variable, panel mounted, resistor. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 86097 -001 A | | | | | | Drawing number Dash number (see table I) Optional panel seal (see 3.2.1) 2. APPLICABLE DOC

6、UMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contra

7、ct. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-22097 - Resistor, Variable, Nonwire Wound (Adjustment Type), General Specification for. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 70

8、0 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulation

9、s unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Requirements. Requirements shall be in accordance with MIL-PRF-22097, and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified herein (see figure 1,

10、2 or 3). Documentation shall be retained by the manufacturer and available for review by the acquiring activity or contractor upon request. 3.2.1 Optional panel seal. When resistors require the optional panel seal (see figure 4) the letter A shall follow the resistance designator. 3.3 Power rating.

11、The power rating shall be 1 watt at +70oC. Maximum ambient temperature at zero load derating shall be +150oC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E

12、 PAGE 3 Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm 0.010 0.25 0.025 0.64 0.093 2.36 0.190 4.83 0.255 6.48 0.406 10.31 0.011 0.28 0.030 0.76 0.100 2.54 0.234 5.95 0.260 6.60 0.700 17.80 0.020 0.51 0.031 0.79 0.125 3.18 0.240 6.10 0.300 7.60 1.334 33.88 0.021 0.53 0.085 2.16 0.150 3.8

13、1 0.250 6.35 0.313 7.95 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Recommended panel hole number 10 drill, 0.194 (4.93 mm). 4. Unless otherwise specified, tolerances are 0.010 (0.25 mm) 5. The picturization of the styles above are given as re

14、presentative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. FIGURE 1. Resistor, solder hook terminations. Provided by IHSNot for ResaleNo reproduction or networking

15、permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 4 Inches mm Inches mm Inches mm Inches mm Inches mm 0.010 0.25 0.025 0.64 0.093 2.36 0.234 5.94 0.313 7.95 0.011 0.28 0.030 0.76 0.100 2.54 0.240 6.10 0.406 10.31

16、0.020 0.51 0.031 0.79 0.125 3.18 0.250 6.35 1.334 33.88 0.021 0.53 0.085 2.16 0.190 4.83 0.255 6.48 6.000 152.40 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Recommended panel hole number 10 drill, 0.194 (4.93 mm). 4. Unless otherwise specified

17、, tolerances are 0.010 (0.25 mm) 5. The picturization of the styles above are given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. FIGURE 2. Resist

18、or, flexible leads. 3 LEADS 6.00 INCH LENGTH STANDS, 30 AWGProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 5 Inches mm Inches mm Inches mm Inches mm Inc

19、hes mm Inches mm Inches mm 0.001 0.03 0.021 0.53 0.031 0.79 0.100 2.54 0.234 5.95 0.260 6.60 0.700 17.80 0.010 0.25 0.025 0.64 0.085 2.16 0.125 3.18 0.240 6.10 0.313 7.95 0.900 22.99 0.011 0.28 0.028 0.71 0.093 2.36 0.150 3.81 0.250 6.35 0.406 10.31 1.334 33.88 0.020 0.51 0.030 0.76 0.095 2.41 0.190

20、 4.83 0.255 6.48 0.500 12.70 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information. 3. Recommended panel hole no. 10 drill, 0.194 (4.93 mm). 4. Unless otherwise specified, tolerances are 0.010 (0.25 mm) 5. The picturization of the styles above are given as repre

21、sentative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable. FIGURE 3. Resistor, with PC pins. .028 .001Provided by IHSNot for ResaleNo reproduction or networking permit

22、ted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 6 Inches mm 0.015 0.039 0.035 0.89 0.040 1.02 0.190 4.83 0.290 7.37 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3.

23、Unless otherwise specified, tolerances are 0.010 (0.25 mm) FIGURE 4. Optional panel seal. 3.4 Terminals. Resistors are available with flexible leads, solder hook terminations, and with PC pins. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

24、ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 7 3.5 Nominal resistance value. The nominal resistance value shall be as specified in table I herein. TABLE I. Resistance values and terminations. Part number 86097- Resistance value Termination (see figure 1)

25、Termination (see figure 2) Termination (see figure 3) in ohms 1/ 001 021 041 10 002 022 042 20 003 023 043 50 004 024 044 100 005 025 045 200 006 026 046 500 007 027 047 1k 008 028 048 2k 009 029 049 5k 010 030 050 10k 011 031 051 20k 012 032 052 25k 013 033 053 50k 014 034 054 100k 015 035 055 200k

26、 016 036 056 250k 017 037 057 500k 018 038 058 750k 019 039 059 1M 020 040 060 2M 1/ k = kilohms, M = megohms 3.6 Actual effective electrical travel. The actual effective electrical travel shall be 17 turns minimum and 27 turns maximum. 3.7 Operating torque. Operating torque shall be a maximum of 5.

27、0 ounce-inches. 3.8 Absolute minimum resistance. The absolute minimum resistance shall be 2 ohms maximum. 3.9 Temperature coefficient. The temperature coefficient shall be 100 ppm/oC maximum. 3.10 Contact resistance variation. The contact resistance variation shall be 3 percent or 3 ohms (whichever

28、is greater). 3.11 Maximum voltage. The maximum voltage shall be 400 volts. 3.12 Temperature range. The temperature range shall be - 55oC to + 150oC. 3.13 Marking. Resistors shall be marked with a part or identification number (PIN) assigned herein (see 1.2), and manufacturers name and Commercial and

29、 Government Entity (CAGE) code. Marking shall remain legible at the end of testing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 8 3.14 Certificate o

30、f compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.15 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible

31、provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.16 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and parts shall be free from any defects that will affect lif

32、e, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and B inspections of MIL-PRF-22097. 4.2.2 Certif

33、ication. The procuring activity may accept a certificate of compliance in lieu of group B inspection. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-

34、house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the military servic

35、es system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which ma

36、y be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application. 6.2 Ordering data. The contract

37、 or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery. One copy of the conformance inspection data with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or

38、provides certification of compliance with group B requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLYCENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 86097 REV E PAGE 9 6.3 User of record. Coordination of th

39、is document for future revisions are coordinated only with the suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3

40、990 or by telephone (614) 692-0552 or DSN 850-0552. 6.4 Suggested source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office

41、 Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing number 86097- Similar part number 1/ Vendor CAGE Vendor name and address 001 011 002 012 003 013 004 014 005 015 3059J-1-XXXM 006 016 007 017 008 018 009 019 010 020 021 031 022 032 023 033 024 034 Bourns

42、 Incorporated 025 035 3059L-1-XXXM 32997 Trimpot Division 026 036 1200 Columbia Avenue 027 037 Riverside, CA 92507 028 038 029 039 030 040 041 051 042 052 043 053 044 054 045 055 3059P-1-XXXM 046 056 047 057 048 058 049 059 050 060 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-