DLA DSCC-DWG-86128 REV A-2008 SHIELDING GASKET ELECTRONIC RFI D TYPE CONNECTOR.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Incorporated boilerplate updates. Inactivated drawing due to lack of approved sources of supply. 6 May 2008 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV A A A A A A A REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 PMIC N/A

2、 PREPARED BY James T. Walker DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Randy Larson APPROVED BY Ivan R. Jones TITLE SHIELDING GASKET, ELECTRONIC, RFI, D TYPE CONNECTOR SIZE A CODE IDENT. NO. 14933 DWG NO. 86128 Original date of drawing 16 December 1986 REV A

3、PAGE 1 OF 7 AMSC N/A 5999-E210 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Notice of Inactivation for New Design DSCC Drawing 86128 is inactivate for new design and is no longer used, except for replacement purposes. Provi

4、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 86128 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV A SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirement for a family of electronic shielding gaskets.

5、 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 86128 -01 Drawing number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other

6、sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, wheth

7、er or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the so

8、licitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-129 - Military Marking For Shipment and Storage. MIL-STD-202 - Electronic and Electrical Component Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil/ or from th

9、e Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

10、 solicitation or contract. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ISO-10012-1 - Equipment, Quality Assurance Requirements for Measuring - Part I: Metrological Confirmation Systems for Measuring Equipment. NCSL-Z540-1 - Laboratories, Calibration and measuring and Test Equipment. (Copies can be

11、obtained online at www.ansi.org or from American National Standards Institute, 1819 L. Street, NW, 6th floor, Washington DC 20036.) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME INTERNATIONAL) ASME B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay). (Copies can be obtained online at www

12、.asme.org of from American Society of Mechanical Engineers International, Three Park Avenue, New York, NY 10016-5990). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 86128 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO S

13、IZE A REV A SHEET 3 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM INTERNATIONAL) ASTM B36/B36M - Brass Plate, Sheet, Strip and Rolled Bar. ASTM B339 - Pig Tin. ASTM B545 - Tin, Electrodeposited Coatings of. (Copies can be obtained online at www.astm.org or from ASTM International, 100 Barr Harbor

14、 Drive, P. O. Box C700, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations

15、unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Conformance inspection. Gaskets shall be products that have been inspected and passed the conformance inspection. 3.2 Material. The gaskets shall be made of .006 thick brass sheet in accordance with ASTM B36/B36M. 3.3 Interface and p

16、hysical dimensions. Interface and physical dimensions of the gaskets shall be as specified in this drawing (see figure 1). 3.4 Plating. The gaskets shall be plated on both sides with bright tin, 200 to 600 microinches thick, in accordance with ASTM B339 and ASTM B545. Hot-dip plating method shall be

17、 used. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of gasket components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6 Mounting surface fl

18、atness. The maximum allowable deviation from flat on gasket mounting surface shall not exceed .004 inch per inch Full Indicator Movement (FIM). 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum

19、 extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.8 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall perform the group A insp

20、ection specified herein on a sample of parts agreed upon by the manufacturer and DSCC-VA. 3.9 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.10 Pure tin. The use of pure tin, as an underplate or final finis

21、h is prohibited both internally and externally. Tin content of gasket components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.11 Marking. The gaskets shall not be marked. Packaging shall be marked in accordance with MIL-

22、STD-129. 3.12 Workmanship. Items shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that will affect life and serviceability. Gaskets shall be finished smooth and shall have rounded edges with no evidence of chipping, cracking, deteriorati

23、on, disintegration, or burrs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 86128 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV A SHEET 4 Dimensions Inches mm Dash number 86128 A B C .010 Ltr Min Max Min Max

24、 -01 -02 -03 -04 .746 1.074 1.614 2.266 .984 1.312 1.852 2.500 1.220 1.555 2.100 2.730 D E F G H J K .790 .395 .104 .395 .115 dia .001 .005 .810 .405 .106 .405 .125 dia .011 .015 20.07 10.03 2.64 10.03 2.92 dia 0.03 0.13 20.57 10.29 2.69 10.03 3.18 dia 0.28 0.38 NOTES: 1. Dimensions are in inches. 2

25、. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm). FIGURE 1. Interface and physical dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 86128

26、 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV A SHEET 5 4. VERIFICATION 4.1 Test equipment and inspection facilities. Test and measuring equipment and inspection facilities of sufficient accuracy, quality, and quantity to permit performance of the required inspection shall be establishe

27、d and maintained by the contractor. The establishment and maintenance of a calibration system to control the accuracy of the measuring and test equipment shall be in accordance with ISO-10012-1 and NCSL-Z540-1. 4.2 Classification of inspections. The inspections specified herein are classified as fol

28、lows: a. Materials and finish inspection. b. Conformance inspection. 4.3 Materials and finishes inspection. Materials and finishes inspection shall consist of certification supported by verifying data that the materials and finishes listed in table I, used in fabricating and finishing the components

29、, are in accordance with the applicable drawing or requirements prior to such fabrication. TABLE I. Materials and finishes inspection. Material or finish Requirement paragraph Applicable specification Brass sheet - ASTM B36/B36M Tin plating - ASTM-B339 and ASTM B545 4.4 Inspection conditions. Unless

30、 otherwise specified herein, all inspections shall be performed in accordance with the test conditions specified in the “General Requirements“ of MIL-STD-202. 4.5 Conformance inspection. 4.5.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection

31、in accordance with table II. TABLE II. Group A inspection. Inspection Requirement paragraph Visual and mechanical Dimensions Surface flatness Marking Workmanship 3.3 3.6 3.11 3.12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 D

32、WG NO. 86128 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV A SHEET 6 Table III. Lot and sample size Lot size Sample size 1 to 544 545-3,072 3,073 and over 80 units 128 units 192 units 4.6 Methods of inspection. 4.6.1 Visual and dimensional inspection. Gaskets shall be examined to verify

33、that the design, construction, physical dimensions, and workmanship are in accordance with the applicable requirements (see 3.1, 3.2, 3.5, and 3.6.) 4.6.2 Mounting surface flatness (see 3.4). Mounting surface flatness shall be measured in accordance with ASME B46.1. 4.6.3 Surface roughness (see 3.5)

34、. Mounting surface roughness shall be measured in accordance with ASME B46.1. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personn

35、el, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packa

36、ging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not

37、mandatory.) 6.1 Intended use. Devices conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application. 6.2 Ordering data. The contract or purchase order should s

38、pecify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, and one copy of the conformance inspection data or the certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the grou

39、p A inspection or provides a certificate of compliance with group A requirements. d. Requirements for notification of change in product to acquiring activity, if applicable. e. Requirements for packaging and packing. 6.3 Replaceability. Devices covered by this drawing will replace the same commercia

40、l device covered by a contractor prepared specification or drawing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can dev

41、elop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information

42、 on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CODE IDENT NO. 14933 DWG NO. 86128 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A REV A SHEET 7

43、6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:relaydla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-