DLA DSCC-DWG-87073 REV D-2007 RESISTOR NETWORK FIXED FILM EIGHT PIN SIP MULTIPLE RESISTANCE VALUES MULTIPLE SCHEMATICS (LOW PROFILE)《电阻网络 固定性 胶片 8-PIN SIP 多层电阻阻值 复合图表(薄层)》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new source of supply; change temperature coefficient of schematic 08. Editorial changes throughout. 29 May 92 D. MOORE B Changes in accordance with NOR 5905-R013-93. 28 May 93 D. MOORE C Update and validation of drawing. Editorial changes throughout. 11

2、 Sep 00 K. COTTONGIM D Add pure tin prohibition paragraph. Editorial changes throughout. 2 Feb 07 M. RADECKI CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV S

3、TATUS OF PAGES REV D D D D D D D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A PREPARED BY Alan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing: 11 November 1987 CHECKED BY David W. Withrow TITLE RESISTOR NETWORK, F

4、IXED, FILM, 8-PIN SIP, MULTIPLE RESISTANCE VALUES, MULTIPLE APPROVED BY David E. Moore SCHEMATICS, (LOW PROFILE) SIZE A CODE IDENT. NO. 14933 DWG NO. 87073 REV D PAGE 1 OF 16 AMSC N/A 5905-E626 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

5、ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an 8-pin, low profile, single-in-line package (SIP), fixed, film, resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is a

6、s follows: 87073 - 01 Drawing number Schematic number (see figure 2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise

7、specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE

8、 STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

9、 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, superse

10、des applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item Requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface a

11、nd physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 3 Inches mm Inches mm I

12、nches mm 0.002 0.05 0.019 0.48 0.125 3.17 0.005 0.006 0.12 0.15 0.098 0.100 2.48 2.54 0.200 0.800 5.08 20.32 0.010 0.25 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, dimensional tolerances shall be 0.02 (0.5 mm) for t

13、wo decimal places and 0.010 (0.25 mm) for three decimal places. 4. The picturization of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, ar

14、e acceptable. FIGURE 1. Resistor network. 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance value shall be as specified on figure 2. 3.3.2 Resistance tolerance. The resistance tolerance shall as specified on figure 2. 3.3.3 Resistor power rating. The resistor power rating for individu

15、al resistors shall be 125 milliwatts maximum at 70oC derated to 0 watts at 150oC. 3.3.4 Package power rating. The package power rating shall not exceed the sum of the individual resistance element power rating in the network. 3.3.5 Operating voltage. Each resistor element shall have a maximum operat

16、ing voltage of 100 V dc or ac rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 4 3.3.6 Schematic. Resistor networks are available in schematics lis

17、ted on figure 2. 3.3.7 Resistance temperature characteristic. Unless otherwise specified, the resistance temperature characteristic shall be 100 ppm/oC. 3.4 Characteristic. The characteristic shall be in accordance with MIL-PRF-83401, characteristic K. 3.5 Pure tin. The use of pure tin, as an underp

18、late or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.6 Environmental requirements. The environmental requirements shall be in

19、accordance with MIL-PRF-83401, characteristic K. 3.7 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers CAGE number or trade mark and date code. 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, rec

20、overed, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance

21、shall be required from manufacturers requesting to be listed as a suggested source of supply. 3.10 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection

22、 is not applicable to this document. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-83401. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate o

23、f compliance with group B requirements in lieu of performing group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 4.4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction

24、, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performe

25、d by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the m

26、ilitary services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted with

27、out license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 5 NOTES: 1. Resistance tolerance shall be 2 percent, except for R5 that shall be 1 ohm. 2. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor t

28、emperature coefficient shall be 200 ppm/oC. 3. Power rating shall be 30 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO

29、 SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 6 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC. 3. Power rating shall be 30 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor tempera

30、ture coefficient shall be 200 ppm/oC. 3. R1 and R6 power rating shall be 60 mW at +120oC. R2, R3, R4, R5 and R7 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permit

31、ted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 7 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. R2, R4 and R5 power ratings shall be 60 mW at +

32、120oC. R1 and R3 power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 30 mW at +120oC. 4. k = kilohms. FIGURE 2. Schematic, resistance and tolerance

33、- Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 8 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient s

34、hall be 200 ppm/oC maximum. 3. R4 power rating shall be 60 mW at +120oC. R1, R2, R3 and R5 power ratings shall be 25 mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 2 percent. 2. Resistor temperature coefficient shall be 100 ppm/oC maximum. 3. R1 and R2 power rating sha

35、ll be 250 mW at +70oC, R3 power ratings shall be 50 mW at +70oC, R4 power ratings shall be 20 mW at +70oC, R5 power ratings shall be 150 mW at +70oC, and R6 power ratings shall be 100 mW at +70oC. 4. = ohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo r

36、eproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 9 NOTES: 1. Resistance tolerance shall be 2 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating sh

37、all be 25 mW at +120oC. 4. k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 25 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot

38、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 10 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3.

39、Power rating shall be 25mW at +120oC. 4. = ohms, k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 40 mW at +120oC. 4. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provi

40、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 11 NOTES: 1. Resistance tolerance shall be 5 percent. 2. k = kilohms. NOTES: 1. Resistance tolerance shall b

41、e 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 30 mW at +120oC. 4. k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

42、 ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 12 NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 40 mW at +120oC. 4. k = kilohms. NOTES: 1. Resistance tolerance

43、shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 30 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

44、IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 13 NOTES: 1. Resistance tolerance shall be 2 percent. 2. Resistor temperature coefficient shall be 150 ppm/oC maximum. 3. k = kilohms. NOTES: 1. Resistance tolerance shall be 2 percent. 2. k =

45、kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 14 NOTES: 1. Resistance tolerance s

46、hall be 2 percent. 2. k = kilohms. NOTES: 1. Resistance tolerance shall be 3 percent. 2. Resistor temperature coefficient shall be 200 ppm/oC maximum. 3. Power rating shall be 40 mW at +120oC. 4. = ohms, k = kilohms. FIGURE 2. Schematic, resistance and tolerance - Continued. Provided by IHSNot for R

47、esaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87073 REV D PAGE 15 NOTES: 1. R7 resistance tolerance shall be 5 percent. R1through R6 resistance tolerance shall be 2 percent. 2. The R1/R2 rat

48、io tolerance shall be 1.399 1 percent; tracking shall be 50 ppm/oC maximum. 3. The R4/R3 ratio tolerance shall be 1.100 1 percent; tracking shall be 50 ppm/oC maximum. 4. The R5/R6 ratio tolerance shall be 1.420 1 percent; tracking shall be 50 ppm/oC maximum. 5. k = kilohms. FIGURE 2. Schematic, resistance and to