DLA DSCC-DWG-87103 REV C-2007 RESISTOR NETWORK 9-PIN SIP MULTIPLE VALUES MULTIPLE TOLERANCES LOW PROFILE《电阻网络 9-PIN SIP 多层电阻阻值 多层公差 薄层》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5905-R006-93 28 MAY 93 D. Moore B Update and validation of drawing. Editorial changes throughout. 11 JUL 00 K. Cottongim C Add pure tin prohibition paragraph. Editorial changes throughout. 7 FEB 07 M. Radecki CURRENT DESIGN AC

2、TIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV C C C C C C C C C C C C REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Allan R. Knox DESIGN ACTIVITY

3、 DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 CHECKED BY David W. Withrow APPROVED BY David E. Moore TITLE RESISTOR NETWORK, 9-PIN SIP, MULTIPLE VALUES, MULTIPLE TOLERANCES, LOW PROFILE SIZE A CODE IDENT. NO. 14933 DWG NO. 87103 Original date of drawing 3 February 1988 REV C PAGE 1 OF 1

4、2 AMSC N/A 5905-E603 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 9 pin single i

5、n line package (SIP). 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 87103 - * Drawing number Schematic Number 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part o

6、f this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Film, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed

7、 Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Des

8、k, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regul

9、ations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 and as specified herein. 3.2 Interface, and physical dimensions. The resistor shall meet the interface, and physical dimensions as s

10、pecified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 3 Inches .002 .005 .006 .010 mm 0.05 0.12 0.15 0.2

11、5 Inches .015 .019 .040 .049 mm 0.38 0.48 1.01 1.24 Inches .100 .125 .200 .900 mm 2.54 3.17 5.08 22.86 NOTES: 1. All dimensions are in inches. 2. Metric equivalents are given for general information. 3. Unless otherwise specified, dimensional tolerance shall be .02 (0.5 mm) for two place decimals an

12、d .010 (0.25 mm) for three place decimals. FIGURE 1. Resistor network 9-pin SIP. 3.3 Electrical characteristics. 3.3.1 Power rating. Unless otherwise specified, each individual resistance element shall have a maximum power rating of 125 milliwatts at 70C. All individual resistance elements are derat

13、ed linearly to zero power at 150C. The total power dissipated by the package shall not exceed the sum of the individual resistance element power rating in the network. 3.3.2 Voltage rating. Each resistor element shall have a maximum voltage rating of 100 V dc or ac rms. 3.3.3 Resistance temperature

14、coefficient. Unless otherwise specified, the resistance temperature coefficient shall be 100 ppm/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 4 3

15、3.4 Resistance. The resistance values shall be in accordance with figure 2 through figure 16. 3.3.5 Resistance tolerance. The resistance tolerance shall be in accordance with figure 2 through figure 16. 3.3.6 Schematics. Resistor networks are available in schematics listed on figure 2 through figur

16、e 16. 3.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.5 Environmental requ

17、irements. Resistor networks shall be in accordance with all the environmental requirements of MIL-PRF-83401, for characteristic “K”. 3.6 Marking. Marking shall be in accordance with MIL-STD-1285 except the PIN shall be as specified in 1.2, with the manufacturers name or CAGE and date lot codes. 3.7

18、Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous li

19、fe cycle costs. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.9 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. NOTES: 1.

20、Resistor tolerance shall be 2 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 50 ppm/C. FIGURE 2. Schematic 01. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO S

21、IZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 5 NOTES: 1. Resistor tolerance shall be 5 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 50 ppm/C. FIGURE 3. Schematic 02. NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilo

22、hms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Resistor power dissipation shall be capable of withstanding at least 50 milliwatts at 120C. FIGURE 4. Schematic 03. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUP

23、PLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 6 NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating for R3 and R6 shall be 50 milliwatts at 120C. R1, R2, R4, and R

24、5s power rating shall be 25 milliwatts at 120C. FIGURE 5. Schematic 04. NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating for R3 and R9 shall be 60 milliwatts at 120C. R1, R2, R4, R5, R6, R7,

25、and R8s power rating shall be 25 milliwatts at 120C. FIGURE 6. Schematic 05. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 7 NOTES: 1. Resistor toler

26、ance shall be 1 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 50 ppm/C. FIGURE 7. Schematic 06. NOTES: 1. Resistor tolerance shall be 1 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 50 ppm/C. FIGURE 8. Schemati

27、c 07. NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating for R3 and R5 shall be 50 milliwatts at 120C. R1, R2, R4, R6, and R7s power rating shall be 25 milliwatts at 120C. FIGURE 9. Schematic 0

28、8. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 8 NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor

29、temperature coefficient shall be 200 ppm/C. 4. Power rating for R3 and R6 shall be 50 milliwatts at 120C. R1, R2, R4, and R5s power rating shall be 25 milliwatts at 120C. FIGURE 10. Schematic 09. NOTES: 1. Resistor tolerance shall be 2 percent. 2. Resistance values are in kilohms. 3. Resistor temper

30、ature coefficient shall be 200 ppm/C. 4. Power rating shall be 25 milliwatts at 120C. FIGURE 11. Schematic 10. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV

31、 C PAGE 9 NOTES: 1. Resistor tolerance shall be 2 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating shall be 25 milliwatts at 120C. FIGURE 12. Schematic 11. NOTES: 1. Resistor tolerance shall be 2 percent. 2. Resistance values are i

32、n kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating shall be 25 milliwatts at 120C. FIGURE 13. Schematic 12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDEN

33、T NO. 14933 DWG NO. 87103 REV C PAGE 10 NOTES: 1. Resistor tolerance shall be 5 percent for R1, R2, R3, R4, and R5s resistance tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. FIGURE 14. Schematic 13. NOTES: 1. Resistor tolera

34、nce shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficient shall be 200 ppm/C. 4. Power rating for R3 and R9 shall be 60 milliwatts at 120C. R1, R2, R4, R5, R6, R7, and R8s power rating shall be 25 milliwatts at 120C. FIGURE 15. Schematic 14. Provided by IHSNot

35、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 11 NOTES: 1. Resistor tolerance shall be 3 percent. 2. Resistance values are in kilohms. 3. Resistor temperature coefficie

36、nt shall be 200 ppm/C. 4. Power rating for R1 and R6 shall be 60 milliwatts at 120C. R2, R3, R4, R5, and R7s power rating shall be 25 milliwatts at 120C. FIGURE 16. Schematic 15. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document. 4.2 Conformanc

37、e inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspection of MIL-PRF-83401. 4.2.1.1 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of p

38、erforming group B tests (see 6.2d). 4.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-83401. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is

39、 to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency,

40、or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking

41、 permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 87103 REV C PAGE 12 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Resistor networks

42、 described herein are intended for use in electronic circuits where miniaturization is required. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certification of

43、compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. 6.3 Tin whisker growth. The u

44、se of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings

45、applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin)

46、 6.4 User of record. Coordination of this document for future revisions is coordinated only with the suggested source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Pos

47、t Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.5 Suggested source of supply. Suggested source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistord

48、la.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 87103 Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address 87103-* 9SM-XXXX-FX 17826 Vishay Techno 4051 Greystone Drive Ontario, CA 91761 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permit