DLA DSCC-DWG-88011 REV E-2004 CAPACITOR CERAMIC SWITCH MODE POWER SUPPLY CG《开关式电压电源陶瓷制电容器》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested source of supply, additions and corrections. 5 August 88 Edward H. Back B Updated to reference MIL-PRF-49470. Added option for J and L lead styles. Added and deleted suggested sources of supply. 2 March 2000 Kendall A. Cottongim C Removed su

2、ggested source of supply. 16 November 00 Kendall A. Cottongim D Updated name and address of vendor B and corrected part numbers on page 16. 18 December 02 Kendall A. Cottongim E Added Johanson Dielectrics as a suggested source of supply. 18 August 2004 Kendall A. Cottongim Prepared in accordance wit

3、h ASME Y14.100 Selected item drawing REV E E E E E E E E E E E E E E E E REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH CHECKED BY EDWARD H. BACK APPROVED BY DAVID E. MOORE TITLE CAPACITOR, CERAMIC,

4、SWITCH MODE POWER SUPPLY, CG SIZE A CODE IDENT. NO. 14933 DWG NO. 88011 Original date of drawing 2 March 1988 REV E PAGE 1 OF 16 AMSC N/A 5910-E310CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo

5、 reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49470 describe the requirements for ceramic switch mode power supply capacitors. 1.2 Part

6、 or Identifying Number (PIN). The complete PIN shall be as follows: 88011 -XXX - | | | | Drawing Dash number Lead style number (see table I) (if required) (see 3.1.1) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, stand

7、ards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see

8、6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49470 - Capacitor, Fixed, Ceramic Dielectric, Switch Mode Power Supply (General Purpose and Temperature Stable) Standard Reliability and High Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods Standard

9、 Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Service, Building 4D (DPM-DODSSP), 700

10、 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spe

11、cific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49470 and herein (see figure 1 and table I). 3.1.1 Lead style. The lead style shall be N configuration (straight) unless the letter J or L

12、is included in the PIN. When requested by the procuring activity, an optional lead style shall be identified by a single letter following the dash number as follows: J - Lead style J L - Lead style L 3.1.2 Case. Multi-layer, unencapsulated, monolithic (see figure 1). 3.1.3 Operating temperature rang

13、e. The operating temperature range shall be -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 3 NOTES: 1. Dimensions are in inches. 2. Metri

14、c equivalents are given for general information only. 3. Unless otherwise specified, tolerances are .010 inch (0.25 mm). 4. Lead frame configuration is shown as typical above the seating plane. 5. See table I for specific maximum A dimension. For maximum B dimension, add .065 inch (1.65 mm) to the a

15、ppropriate A dimension. For all lead styles, the number of chips is determined by the capacitance and voltage rating. 6. For case code 5, dimensions shall be .100 inch (2.54 mm) maximum and .012 inch (0.30 mm) minimum. 7. Lead alignment within pin rows shall be within .005 inch (0.13 mm). FIGURE 1.

16、Dimensions and configuration. Inches mm .002 0.05 .010 0.25 .020 0.51 .025 0.64 .050 1.27 .055 1.40 .070 1.78 .100 2.54 .224 5.69 .250 6.35 .275 6.98 .300 7.62 .350 8.89 .400 10.16 .425 10.80 .440 11.18 .450 11.43 .500 12.70 .800 20.32 .870 22.10 .950 24.13 1.075 27.30 1.250 31.75 1.350 34.29 1.450

17、36.83 1.535 38.99 1.950 49.53 2.075 52.70 .010 RAD (TYP)LEAD STYLE J.0700.020 .002CIRCUIT DIAGRAM.050 MINLEAD STYLE LLEAD STYLE N.070.010 RAD(TYP)EC.010 .0020.100 TYPSEATING PLANESEE NOTE 4BSEE.010SEENOTE 6E.250 MIN.010.010E.050 MIN.055SEE NOTE 70.100 MAX0.025 MIN0.250 MINANOTE 5DDimensions D Case c

18、ode C .025 Min Max E (max) Number of leads per side 1 .450 1.950 2.075 .500 20 2 .800 1.450 1.535 .870 15 3 .450 .950 1.075 .500 10 4 .400 .350 .425 .440 4 5 .250 .224 .275 .300 3 6 1.250 1.950 2.075 1.350 20 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

19、HS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 4 3.2 Electrical characteristics. 3.2.1 Rated voltage. See table I. 3.2.2 Dielectric. BP, in accordance with MIL-PRF-49470. 3.2.3 Temperature coefficient. Temperature coefficient shall be 0 30 ppm

20、/C. 3.2.4 Capacitance. See table I. Capacitors shall be measured in accordance with method 305 of MIL-STD-202. The following details and exceptions shall apply: 1 kHz 100 Hz at 1.0 V rms 0.2 V rms (open circuit voltage). 3.2.5 Dissipation factor (+25C). Dissipation factor shall be .15 percent maximu

21、m (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. a. At +25C, rated voltage: 100,000 megohms or 1,000 megohms-F, whichever is less. b. At +125C, rated voltage: 10,000 megohms or 100 megohms-F, whichever is less. 3.2.7 Dielectric withstanding voltage. In accordance w

22、ith MIL-PRF-49470. 3.2.8 Capacitance tolerance. J = 5 percent, K = 10 percent. 3.3 Thermal shock and voltage conditioning. In accordance with MIL-PRF-49470. 3.4 Solderability. In accordance with MIL-PRF-49470. 3.5 Vibration, high frequency. In accordance with MIL-PRF-49470. 3.6 Immersion. In accorda

23、nce with MIL-PRF-49470. 3.7 Shock, specified pulse. In accordance with MIL-PRF-49470. 3.8 Moisture resistance. In accordance with MIL-PRF-49470. 3.9 Resistance to soldering heat. In accordance with MIL-PRF-49470. 3.10 Resistance to solvents. In accordance with MIL-PRF-49470. 3.11 Terminal strength.

24、In accordance with MIL-PRF-49470. 3.12 Life (at elevated ambient temperature). In accordance with MIL-PRF-49470. 3.13 Marking. Marking shall be in accordance with MIL-STD-1285, except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturers name or Commercial and Government

25、 Entity (CAGE) code and date lot code minimum. Case sizes 4 and 5 shall be marked with coded cap and tolerance minimum. Full marking shall be included on the package. 3.14 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials shoul

26、d be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to b

27、e a suggested source of supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 5 3.16 Workmanship. Capacitors shall be processed in such a manner as to

28、be uniform in quality when using 2X minimum to 4X maximum magnification. External leads shall not exhibit cuts, nicks, or scrapes exceeding 10 percent of the diagonal length of the leads. The surface of the lead may exhibit bare base metal on the edges and cut ends of the pins but not on the flat po

29、rtion of the leads. These capacitor leads are not expected to be solderable above the seating plane. TABLE I. Electrical characteristics. DSCC drawing PIN 88011- Capacitance value F Capacitance tolerance Case code Maximum A dimension 50 V 001 .056 J 5 .120 002 .056 K .120 003 .068 J 5 .240 004 .068

30、K .240 005 .082 J 5 .240 006 .082 K .240 007 .1 J 5 .240 008 .1 K .240 009 .12 J 5 .360 010 .12 K .360 011 .15 J 5 .360 012 .15 K .360 013 .18 J 5 .480 014 .18 K .480 015 .22 J 5 .480 016 .22 K .480 017 .27 J 5 .650 018 .27 K .650 019 .33 J 4 .360 020 .33 K .360 021 .39 J 4 .480 022 .39 K .480 023 .

31、47 J 4 .480 024 .47 K .480 025 .56 J 4 .650 026 .56 K .650 027 .68 J 3 .240 028 .68 K .240 029 .82 J 3 .240 030 .82 K .240 031 1 J 3 .360 032 1 K .360 033 1.2 J 3 .360 034 1.2 K .360 035 1.5 J 3 .480 036 1.5 K .480 037 1.8 J 3 .480 038 1.8 K .480 039 2.2 J 3 .650 040 2.2 K .650 041 2.7 J 1 .360 042

32、2.7 K .360 043 3.3 J 1 .480 044 3.3 K .480 045 3.9 J 1 .480 046 3.9 K .480 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 6 TABLE I. Electrical characte

33、ristics - Continued. DSCC drawing PIN 88011- Capacitance value F Capacitance tolerance Case code Maximum A dimension 50 V 047 4.7 J 1 .650 048 4.7 K .650 049 5.6 J 2 .650 050 5.6 K .650 051 6.8 J 6 .360 052 6.8 K .360 053 8.2 J 6 .360 054 8.2 K .360 055 10 J 6 .480 056 10 K .480 057 12 J 6 .480 058

34、12 K .480 059 15 J 6 .650 060 15 K .650 100 V 061 .047 J 5 .240 062 .047 K .240 063 .056 J 5 .240 064 .056 K .240 065 .068 J 5 .240 066 .068 K .240 067 .082 J 5 .240 068 .082 K .240 069 .1 J 5 .360 070 .1 K .360 071 .12 J 5 .360 072 .12 K .360 073 .15 J 5 .480 074 .15 K .480 075 .18 J 5 .480 076 .18

35、 K .480 077 .22 J 5 .650 078 .22 K .650 079 .27 J 4 .360 080 .27 K .360 081 .33 J 4 .480 082 .33 K .480 083 .39 J 4 .480 084 .39 K .480 085 .47 J 4 .650 086 .47 K .650 087 .56 J 4 .650 088 .56 K .650 089 .68 J 3 .240 090 .68 K .240 091 .82 J 3 .360 092 .82 K .360 093 1 J 3 .360 094 1 K .360 095 1.2

36、J 3 .480 096 1.2 K .480 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 7 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- Capaci

37、tance value F Capacitance tolerance Case code Maximum A dimension 100 V 097 1.5 J 3 .480 098 1.5 K .480 099 1.8 J 3 .650 100 1.8 K .650 101 2.2 J 1 .480 102 2.2 K .480 103 2.7 J 1 .480 104 2.7 K .480 105 3.3 J 1 .650 106 3.3 K .650 107 3.9 J 2 .480 108 3.9 K .480 109 4.7 J 2 .650 110 4.7 K .650 111

38、5.6 J 6 .360 112 5.6 K .360 113 6.8 J 6 .360 114 6.8 K .360 115 8.2 J 6 .480 116 8.2 K .480 117 10 J 6 .650 118 10 K .650 119 12 J 6 .650 120 12 K .650 200 V 121 .022 J 5 .120 122 .022 K .120 123 .027 J 5 .240 124 .027 K .240 125 .033 J 5 .240 126 .033 K .240 127 .039 J 5 .240 128 .039 K .240 129 .0

39、47 J 5 .360 130 .047 K .360 131 .056 J 5 .360 132 .056 K .360 133 .068 J 5 .480 134 .068 K .480 135 .082 J 5 .480 136 .082 K .480 137 .1 J 5 .650 138 .1 K .650 139 .12 J 4 .360 140 .12 K .360 141 .15 J 4 .360 142 .15 K .360 143 .18 J 4 .480 144 .18 K .480 145 .22 J 4 .480 146 .22 K .480 Provided by

40、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 8 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- Capacitance value F Capacitance tolerance

41、Case code Maximum A dimension 200 V 147 .27 J 4 .650 148 .27 K .650 149 .33 J 3 .240 150 .33 K .240 151 .39 J 3 .240 152 .39 K .240 153 .47 J 3 .360 154 .47 K .360 155 .56 J 3 .360 156 .56 K .360 157 .68 J 3 .480 158 .68 K .480 159 .82 J 3 .650 160 .82 K .650 161 1 J 3 .650 162 1 K .650 163 1.2 J 1

42、.480 164 1.2 K .480 165 1.5 J 1 .480 166 1.5 K .480 167 1.8 J 1 .650 168 1.8 K .650 169 2.2 J 2 .480 170 2.2 K .480 171 2.7 J 2 .650 172 2.7 K .650 173 3.3 J 6 .360 174 3.3 K .360 175 3.9 J 6 .360 176 3.9 K .360 177 4.7 J 6 .480 178 4.7 K .480 179 5.6 J 6 .650 180 5.6 K .650 500 V 181 .01 J 5 .120 1

43、82 .01 K .120 183 .012 J 5 .240 184 .012 K .240 185 .015 J 5 .240 186 .015 K .240 187 .018 J 5 .240 188 .018 K .240 189 .022 J 5 .360 190 .022 K .360 191 .027 J 5 .360 192 .027 K .360 193 .033 J 5 .480 194 .033 K .480 195 .039 J 5 .480 196 .039 K .480 Provided by IHSNot for ResaleNo reproduction or

44、networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 9 TABLE I. Electrical characteristics - Continued. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformanc

45、e inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of this drawing (see table II and table III herein). DSCC drawing PIN 88011- Capacitance value F Capacitance tolerance Case code Maximum A dimension 500 V 197 .047 J

46、 5 .650 198 .047 K .650 199 .056 J 4 .360 200 .056 K .360 201 .068 J 4 .360 202 .068 K .360 203 .082 J 4 .480 204 .082 K .480 205 .1 J 4 .480 206 .1 K .480 207 .12 J 4 .650 208 .12 K .650 209 .15 J 3 .240 210 .15 K .240 211 .18 J 3 .240 212 .18 K .240 213 .22 J 3 .360 214 .22 K .360 215 .27 J 3 .360

47、 216 .27 K .360 217 .33 J 3 .480 218 .33 K .480 219 .39 J 3 .650 220 .39 K .650 221 .47 J 1 .360 222 .47 K .360 223 .56 J 1 .480 224 .56 K .480 225 .68 J 1 .480 226 .68 K .480 227 .82 J 1 .650 228 .82 K .650 229 1 J 2 .480 230 1 K .480 231 1.2 J 2 .650 232 1.2 K .650 233 1.5 J 6 .360 234 1.5 K .360

48、235 1.8 J 6 .480 236 1.8 K .480 237 2.2 J 6 .650 238 2.2 K .650 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88011 REV D PAGE 10 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B inspections in lieu of performing group B inspections (see 6.2f). See 6.1.3 for guidance. TABLE II. Group A inspection. Inspection Requirement paragraph of MIL-PRF-49470 Test method paragraph of MIL-PRF-49470 Samp