DLA DSCC-DWG-88014 REV E-2011 RESISTOR NETWORK 12-PIN SINGLE-IN-LINE PACKAGE (SIP).pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5905-R008-93. 28 MAY 93 D. Moore B Update vendor list. Editorial changes throughout. 5 JAN 99 A. Ernst C Revise revision letter. Editorial changes throughout 16 JUL 99 W. Sindelar D Add Group B inspection certification paragra

2、ph. Editorial changes throughout. 13 APR 05 K. Cottongim E The molded epoxy case is obsolete and is superseded by conformal coated case. Add pure tin, manufacturer eligibility, and high power pulse paragraphs. Editorial changes throughout. 24 FEB 11 M. Radecki The molded epoxy case is obsolete and i

3、s superseded by conformal coated case. CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV E E E E E E E PAGES 1 2 3 4 5 6 7 PMIC N/A PREPARED BY Allan R.

4、 Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing 7 March 1988 CHECKED BY David W. Withrow TITLE RESISTOR, NETWORK, 12-PIN, SINGLE-IN-LINE PACKAGE (SIP) APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 88014 REV E PAGE 1 OF 7 AMSC

5、 N/A 5905- E751 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a 12 pin, single-in-l

6、ine package (SIP), resistor network. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 88014 - A XXXX G Drawing number Schematic (see figure 1) Resistance value (see 1.2.1.1 and 3.3.1) Resistance tolerance (see 3.3.2) 1.2.1 Schematic. The schematic of the resistor is identified b

7、y a single letter in accordance with the drawings (see figure 1). The resistor element Rrefis the reference resistor element used in determining the ratio accuracy (when applicable). FIGURE 1. Schematic. 1.2.1.1 Resistance value designations. The resistance value designation is in accordance with MI

8、L-PRF-83401. 1.2.1.2 Characteristics. Characteristics is in accordance with MIL-PRF-83401 (characteristic K). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sect

9、ions of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether o

10、r not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solici

11、tation or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 3 DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-83401 - Resistor Networks, Fixed, Fi

12、lm, and Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from

13、the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets),

14、the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be as specified herein. 3.2 Interface and physical di

15、mensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 2). 3.3 Electrical characteristics. 3.3.1 Resistance. The resistance range shall be 10 ohms to 3.3 megohms. 3.3.2 Resistance tolerance. Resistors tolerance shall be 2 percent.

16、 3.3.3 Power ratings. The power rating for schematic A shall be 0.19 watt at 25oC derated to zero power at 150oC (see figure 3). 3.3.4 Package power rating. The package power rating shall be 2.00 watts at 25oC. 3.3.5 Temperature range. The operating temperature range shall be - 55oC to + 150oC. 3.3.

17、6 Resistance temperature characteristic. The resistance temperature characteristic shall not exceed 100 ppm/oC for characteristic K. 3.3.7 TC tracking. The TC tracking shall be 50 ppm/oC. 3.3.8 Operating voltage. The maximum operating voltage shall be 50 V dc. Provided by IHSNot for ResaleNo reprodu

18、ction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 4 Ltr Inches mm Min Max Min Max A - 1.190 - 30.23 B 1.095 1.105 27.81 28.07 C - .200 - 5.08 D .093 .103 2.36 2.62 E .120 .140 3.05 3.56 F - .0

19、50 - 1.27 G .090 .110 2.29 2.79 H .015 .021 0.38 0.53 J .040 .050 1.02 1.27 K .027 .037 0.69 0.94 L .009 .015 0.23 0.38 NOTES: 1. Dimensions are in inches, unless otherwise specified, tolerances are .005 (0.13mm). 2 Metric equivalents are given for general information only. 3. The picturization of t

20、he styles above is given as representative of the envelope of the item. Slight deviation from the outline shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable, (includes conformal coated resistors). 4. Measurement made at the point of e

21、mergence of the lead from the body. 5. Pin 1 locator shall be a bevel, stripe, notch or a dot above pin 1 in the shaded area. 6. If standoffs are located on the body, a minimum of two standoffs are required as illustrated. As an option, additional standoffs may be located on the body of the resistor

22、 network. If leads with standoffs are used, standoffs on the body are not required. * 7. The molded epoxy case as shown in previous revision is obsolete and is superseded by conformal coated case as shown in figure 2. * 8. Leads are along centerline of body. * FIGURE 2. Resistor network. Provided by

23、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 5 FIGURE 3. Derating curve. 3.4 Environmental characteristics. 3.4.1 Moisture resistance. When resistors are teste

24、d as specified in 4.3 there shall be no evidence of mechanical damage. The change in resistance shall not exceed 1.0 percent. * 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not ex

25、ceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.5). 3.6 Marking. Marking shall be in accordance with MIL-STD-1285, except the resistors shall be marked with the PIN assigned herein (see 1.2), manufacturers Commercial and Government Entity (CAGE) code,

26、date code and lot code. 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes

27、economically advantageous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 6 * 3.8 Manufacturer eligibility. To be eligible for listin

28、g as an approved source of supply, a manufacturer shall be listed on the MIL-PRF-83401 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VAT. * 3.8.1 Certificate of comp

29、liance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.9 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and parts shall be free from any defects that will affect life, serviceability, or appear

30、ance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection in accordance with MIL-PRF-83401 is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and B inspections of

31、 MIL-PRF-83401. 4.2.1.1 Group A inspection. Group A inspection shall be in accordance with MIL-PRF-83401. It should be noted that the power conditioning of MIL-PRF-83401 is required to be performed at 25oC and the calculation derived from the derated wattage as shown in figure 3. 4.2.1.2 Group B ins

32、pection. Group B inspection shall be in accordance with MIL-PRF-83401. 4.2.1.2.1 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2c). 4.3 Moisture resistance. Resistors shall be test

33、ed in accordance with MIL-PRF-83401, and the change in resistance shall not exceed 1.0 percent. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house

34、contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services syst

35、em commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be he

36、lpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for the OEM application. Provided by IHSNot for ResaleNo reprod

37、uction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 88014 REV E PAGE 7 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery: On

38、e copy of the conformance inspection data or a certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements (see 4.2.1.

39、2.1). d. Requirements for packaging and packing. 6.3 Precautionary note. Due to the low profile of these parts and the length dimension required for the 12 pins, the parts are more fragile than regular parts and must be inserted into the boards with caution. * 6.4 Electrostatic charge. Under several

40、 combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive

41、packaging procedure. * 6.5 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on p

42、roducts that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard

43、 Specification for Electrodeposited Coatings of Tin). * 6.6 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, damage and premature failure are possible. * 6.7 User of record.

44、 Coordination of this document for future revisions is coordinated only with the approved source of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Off

45、ice Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.8 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mi

46、l or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing number Vendor part number 1/ Vendor CAGE Vendor name and address 88014-* CSC12A01XXXGPA 91637 Vishay Dale Electronics P.O. Box 609 1122 23rd Street Columbus, NE 68602 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-