DLA DSCC-DWG-88041 REV A-2002 SOCKET ADAPTER FOR DISCRETE ELECTRONIC COMPONENTS GENERAL DRAWING FOR《分离式电子元件衔接器插槽总图》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Change CAGE 14933 to 037Z3. Replace canceled MIL-Specs with equivalent industry standards. Editorial changes throughout. 04/18/02 Robert HeberPrepared in accordance with ASME Y14.100 REV PAGE REV A A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 PREPARED

2、BY PMIC - G Dave Leight DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Richard Marbais SOCKET, ADAPTER, FOR DISCRETE ELECTRONIC COMPONENTS, GENERAL DRAWING FOR SIZE CAGE CODE 037Z3 DWG. NO. 88041 Original date of drawing 28 Dec 1988 A REV A

3、PAGE 1 OF 7 AMSC N/A 5935-E643-30 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5

4、000 A REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing covers the requirements for component adapters, which are used to assemble hybrid and special network circuits. The termination portion of the contact, which will be mounted to the printed wiring board, shall simulate those of commonly available in

5、tegrated circuits. The portion of the contact to which the components are mounted shall accommodate discrete components and shall be available in round pin, solder pocket, and slotted pin styles. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as specified on the item requirements dr

6、awing. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are these listed in t

7、he issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATION DEPARTMENT OF DEFENSE STANDARD MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. (Unless otherwise indicated, copies

8、 of the above specifications, standards, and handbook are available from the Defense Printing Service, Detachment Office, Building 4D, Customer Service, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the exte

9、nt specified herein. Unless otherwise specified, the issues of documents, which are DoD adopted, are those listed in the issue DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see

10、 6.2). ASTM INTERNATIONAL (ASTM) ASTM B16 - Rod, Bar, and Shapes for use in Screw Machines, Free Cutting Brass. ASTM B139 - Standard Specification for Phosphor Bronze Rod, Bar and Shapes. ASTM B488 - Standard Specification for Electrodeposited Coatings of Gold for Engineering Uses. ASTM D4507 - Stan

11、dard Specification for Thermoplastic Polyester (TPES) Materials. ASTM D5205 - Standard Classification System for Polyetherimide (PEI) Materials. (Applications for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Dr., West Conshohocken, PA, USA 19428-2959)

12、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 3 Copper Development Association, Inc. - Copper Alloy No. CDA 510. (Application for copies shoul

13、d be addressed to the Copper Development Association, Inc. 260 Madison Avenue, New York, NY 10016.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) SAE-AMS-P-81728 - Plating, Tin-Lead (Electrodeposited). SAE-AMS-QQ-N-290 - Nickel Plating (Electrodeposited). (Applications for copies should be addressed to SAE,

14、 400 Commonwealth Drive, Warrendale, PA 15096.) National Conference of Standards Laboratories (NCSL) ANSI/NCSL Z540-1-1990 - Calibration Laboratories and Measuring and Test Equipment General Requirements. (Applications for copies should be addressed to the National Conference of Standard Laboratorie

15、s, 1800 30thStreet, Suite 305B, Boulder, CO 80301.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 3. REQUIREMENTS

16、 3.1 DSCC requirements drawing. The individual item requirements shall be in accordance with the applicable requirements drawing. In the event of any conflict between requirements of this drawing and the DSCC requirements drawing, the latter shall govern. 3.2 Design, construction, and physical dimen

17、sions. The design, construction, and physical dimensions shall be as specified in the applicable item requirements drawing and those specified herein. 3.2.1 Material. The material for each part shall be as specified herein, If a reference material is not identified, a material shall be used which wi

18、ll enable the adapters to meet the performance requirements of this drawing. 3.2.2 Contacts. Contacts shall be phosphor bronze in accordance with ASTM B139, composition A or B, CDA 510, or brass in accordance ASTM B16. 3.2.3 Insulator. The insulator shall be thermoplastic polyester in accordance wit

19、h ASTM D5205, type PE10110 G30 A00190 E05 EF085 ZN215 polyetherimide in accordance with ASTM D5205 or ASTM 4507, type 110 G30 A45340 FL310 or as specified in the item requirements drawing. 3.3 Finish. Contacts shall be tin-lead plated in accordance with AMS-P-81728. 200 to 340 microinches (0.51 to 0

20、.86 m) thick (5 percent minimum lead) over 30 to 200 microinches copper, or gold in accordance with ASTM B488, type 2, code C, class 0.18 (7.5 microinches) minimum, over 30 to 150 microinches (0.76 to 3.81m) nickel in accordance with AMS-QQ-N-290 as specified in the item requirements drawing. 3.4 De

21、sign and construction. The adapter shall have the configuration as specified by the applicable item requirements drawing. 3.4.1 Workmanship. The adapter shall be uniform in quality and shall be free from burrs, scratches, cracks, voids, sharp edges, and other defects that will adversely affect life

22、or serviceability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 4 3.5 Electrical characteristics. 3.5.1 Current rating. Unless otherwise specif

23、ied, the maximum current rating is 5 amperes when tested with an appropriate size wire. The maximum temperature rise limit shall be 30C above ambient temperature (see 4.2). 3.5.2 Insulation resistance. The insulation resistance shall be 5,000 megohms minimum when tested in accordance with MIL-STD-20

24、2, method 302, test condition C. 3.5.3 Dielectric withstanding voltage. The socket adapter shall have 1,000 V rms between pins when tested in accordance with MIL-STD-202, method 301 at sea level. At an altitude equivalent to 50,000 feet (15.24 km) (high altitude) the test voltage shall be 350 V rms.

25、 There shall be no flashover or insulation breakdown. Test duration shall be 60 seconds. 3.5.4 Capacitance. When measured in accordance with MIL-STD-202, method 305, using a frequency of 1 kHz, the capacitance between adjacent terminal pins shall not exceed 2.0 picofarads. 3.6 Environmental conditio

26、ns. 3.6.1 Thermal shock. When tested in accordance with MIL-STD-202, method 107, test condition F, there shall be no evidence of mechanical damage. 3.6.2 Operating temperature. Operating temperature shall be as specified in the individual detail specification sheets. 3.6.3 Mechanical shock. When tes

27、ted in accordance with MIL-STD-202, method 213, at an acceleration level of 100 G, there shall be no evidence of mechanical damage. 3.6.4 Vibration. When tested in accordance with MIL-STD-202, method 204, with a frequency range of 10 to 2,000 Hz at an acceleration level of 10 G, there shall be no ev

28、idence of mechanical damage. 3.6.5 Salt spray. When tested in accordance with MIL-STD-202, method 101, test condition B (48 hours with a 5 percent salt solution) there shall be no evidence of corrosion that would affect the use of adapter. 3.7Mechanical requirements. Applicable to adapters with wire

29、 wrap terminations. 3.7.1 Torque. When tested in accordance with MIL-STD-202, method 211, test condition E, there shall be no evidence of mechanical damage as a result from exposure of terminals to a 2.0 ounce-force inch (14.12 mN m) torque in both the clockwise and counterclockwise directions. 3.7.

30、2 Axial terminal retention. When tested in accordance with MIL-STD-202, method 211, test condition A, with a force on 7.5 pounds (33.36 N) applied axially at the tip of the terminal, there shall be no evidence of damage or loosening of contacts. 3.7.3 Terminal bend. When tested in accordance with MI

31、L-STD-202, method 211, test condition B, there shall be no evidence of breaking or cracking when the terminal is flexed through an arc of 30 from its true position. 3.8 Mechanical requirements. Applicable to adapters with solder terminations. 3.8.1 Solderability. When tested in accordance with MIL-S

32、TD-202, method 208, the terminal shall display at least 95 percent covering of continuous new solder with no concentration of solder voids in the balance of the area. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88041

33、DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV A PAGE 5 3.8.2 Resistance to soldering heat. When specified (see 3.1), the adapter shall be tested in accordance with MIL-STD-202, method 210, test condition B. The adapter shall be mounted to a glass epoxy printed wiring board. After the

34、 test, there shall be no evidence of damage and it shall conform to all the performance requirements described in 3.4.1 and 3.5.2 herein. 3.9 Manufacturer eligibility. To be eligible to supply adapters to this drawing, the manufacturer must provide a part as specified herein and on the item requirem

35、ents drawing. Test data of part performance must be made available to the Defense Supply Center, Columbus upon request. A current production sample shall be supplied (free of charge and without obligation) to DSCC-VAI or their designated (quality review) agent, before the manufacturer may be listed

36、or solicited for a bid on the applicable drawing. Samples supplied are subject to testing and may not be returned. 3.10 Marking. Marking shall be in accordance with the item requirements drawing. 3.11 Quality assurance requirements. Adapters furnished under this drawing shall have been subjected to

37、and passed all requirements, tests, and inspection details herein including quality conformance inspection. 3.12 Certification of compliance. A certification of compliance shall be required from a manufacturer in order to be listed as an approved source of supply (see 6.4). 4. QUALITY ASSURANCE PROV

38、ISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable f

39、or the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed req

40、uirements. 4.1.1 Equipment calibration. All test equipment and inspection facilities used in the performance of any test shall be maintained in a calibration system in accordance with ANSI/NCSL Z500-1-1990. 4.2 Inspection conditions. Unless otherwise specified herein, all inspections shall be perfor

41、med under the following ambient conditions: a. Temperature: 25C 5C. b. Relative humidity: 30 to 80 percent. 4.3 Qualification inspection. Qualification inspection for adapters specified herein shall not be required. 4.4 Certification as an approved source of supply. In order to be listed as an appro

42、ved source of supply for adapters, a manufacturer shall: a. Agree to make available to DSCC, upon request, all pertinent test data on the subject part indicating compliance to the tests outlined in table I. b. Provide to DSCC-VAI, or its designated agent, upon request, free of change and without obl

43、igation, a current production sample from its production line, of the quantity of units required of the types specified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 88041 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 4

44、3216-5000 A REV A PAGE 6 4.5 Quality conformance. 4.5.1 Recertification. Every three years after the initial certification to a specific item drawing, the manufacturer shall perform the testing specified in table I. The quantity of samples shall be three of each termination type. The samples shall b

45、e the largest size (maximum number of contacts) described by the detail drawing. The data collected shall be retained by the manufacturer and shall be supplied to DSCC-VAI upon request. 4.5.2 Quality conformance inspection. Quality conformance inspection shall be performed on sample units produced w

46、ith equipment and procedures normally used in production see table I, quality conformance inspection. Manufactures shall keep lot records for 3 years minimum, monitor for compliance to the prescribed procedures, and observe that satisfactory manufacturing conditions and records on lots are maintaine

47、d for these adapters. Customers shall make the records, including as a minimum, an attributes summary of all quality conformance inspections on each lot, as requested. TABLE I. Quality conformance inspection. Test Paragraph Visual and mechanical inspection Material and finish Insulation resistance D

48、ielectric withstanding voltage Capacitance 1/ Thermal shock 1/ Mechanical shock 1/ Vibration 1/ Salt spray 1/ Torque 2/ Axial terminal retention 2/ Terminal bend 2/ Solderability 3/ Resistance to soldering heat 3/ 4/ 3.2 3.2.1 and 3.3 3.5.2 3.5.3 3.5.4 3.6.1 3.6.3 3.6.4 3.6.5 3.7.1 3.7.2 3.7.3 3.8.1

49、 3.8.2 1/ Applicable to recertification only. 2/ Applicable to adapters with wire wrap terminations. 3/ Applicable to adapters with solder terminations. 4/ Where specified. 5. PACKAGING 5.1 Packaging requirements. For acquisition purposes, the packaging requirements shall be as specified in the contract or purchase order. When actual packaging of materiel s to be performed by DoD personnel, these personnel need to contact the responsible packa