DLA DSCC-DWG-89012 REV C-2006 CAPACITORS FIXED ELECTROLYTIC POLARIZED ALUMINUM OXIDE LOW SCREW-INSERT《固定极化电解质氧化铝及低螺母插入的电容器》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added capacitance 1,100 F at 350 V dc. Editorial changes throughout. 92/07/14 D. Moore B Editorial changes throughout. 11 Dec 00 K. Cottongim C Editorial changes throughout. 6 June 06 Michael Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS

2、 AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV PAGE REV C C C C C C C C C REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Robert E. Grillot DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER

3、 DAYTON, OH 45444-5000 CHECKED BY Heraldine Johnson APPROVED BY David E. Moore TITLE CAPACITORS, FIXED, ELECTROLYTIC POLARIZED, ALUMINUM OXIDE, LOW SCREW- INSERT Original date of drawing 21 April 1989 SIZE A CODE IDENT. NO. 14933 DWG NO. 89012 REV C PAGE 1 OF 9 AMSC N/A 5910-E210 .Provided by IHSNot

4、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for aluminum oxide, electrolytic capacitors. 1.2 Part or

5、Identifying Number (PIN). The complete PIN shall be as follows: 89012 -XX | | | | Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this docu

6、ment to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-PRF-39018 - Capacitors, Fixed, Electrolytic (Aluminum Oxide), Established Reliability, and Non-establishe

7、d Reliability, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-202 - Test Methods Standard for Electronic and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla.mil/ or htt

8、p:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated spe

9、cifications, specification sheets, or MS sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical

10、 dimensions shall be as specified in MIL-PRF-39018 and herein (see figure 1). 3.1.1 Terminals. Low screw-insert terminals (see figure 1). 3.1.2 Case. Case shall be made with insulated tubular metal. 3.1.3 Operating and storage temperature range. The operating and storage temperature range shall be -

11、40C to +85C. 3.1.4 Insulating sleeves. Insulating sleeves shall meet the requirements of MIL-PRF-39018. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

12、m IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 3 Inches mm .031 0.79 .032 0.81 .063 1.60 .219 5.56 .313 7.95 Inches Millimeters Case code D L M Max Max .016 D L M Max Max 0.40 AA AB AC BB BC BF CC CD CF DF DJ 1.453 2.250 .500 1.453 3.25

13、0 .500 1.453 4.250 .500 2.078 3.250 .875 2.078 4.250 .875 2.078 5.750 .875 2.578 4.250 1.125 2.578 4.750 1.125 2.578 5.750 1.125 3.078 5.750 1.250 3.078 8.750 1.250 36.90 57.15 12.70 36.90 82.55 12.70 36.90 107.95 12.70 52.78 82.55 22.22 52.78 107.95 22.22 52.78 146.05 22.22 65.48 107.95 28.57 65.48

14、 120.65 28.57 65.48 146.05 28.57 78.18 146.05 31.75 78.18 222.25 31.75 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Polyvinyl chloride insulating sleeve to be permanently fixed to aluminum case. FIGURE 1. Case dimensions and configuration. Prov

15、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 4 3.2.2 Dielectric. The dielectric shall be aluminum oxide in accordance with MIL-PRF-39018. 3.2.3 Capaci

16、tance. Nominal capacitance shall be within -10 percent, +100 percent of the value shown in table I at +25C, measured at 120 Hz and 1.0 V rms maximum. 3.2.4 Equivalent series resistance (ESR). Equivalent series resistance at 120 Hz shall not exceed the values shown in table I at +25C, when measured w

17、ith a maximum of 1.0 V rms applied. ESR at 10 kHz is shown in table I. 3.2.5 DC leakage current. DC leakage current shall not exceed values determined from the equation: Where CVkI =I = leakage current in A k = a constant: 4.0 at +25C 32.0 at +85C C = rated capacitance in F V = rated dc voltage In n

18、o case, however, shall the dc leakage current exceed 20,000 A when normally stabilized at +85C. 3.2.6 Ripple current. Capacitors shall withstand the rms ripple current at 120 Hz and +85C (see table I). 3.2.7 Life test. One hundred percent of rated voltage applied at +85C for 1,000 hours. After test,

19、 capacitors shall meet the following: a. Capacitors shall then be removed from the test chamber and stabilized at room temperature. b. The capacitance, when measured in accordance with 3.2.3, shall not have changed more than 15 percent from the initial value. c. The equivalent series resistance, whe

20、n measured in accordance with 3.2.4, shall not have increased to more than 150 percent of the initial requirement. d. The leakage current shall meet the requirement specified in 3.2.5. 3.2.8 Reverse voltage. Not applicable. 3.2.9 Reverse voltage aging. Not applicable. 3.3 Environmental characteristi

21、cs. 3.3.1 Altitude operation. The altitude operation shall not exceed 200,000 feet. 3.3.2 Shelf test. Capacitors shall be subjected to a shelf test at +85C 3C for 500 hours. No voltage shall be applied. After test, capacitors shall be removed from the test chamber and stabilized at room temperature,

22、 and meet the following: a. The capacitance, when measured in accordance with 3.2.3, shall be within 15 percent of the initial measured value. b. The equivalent series resistance, when measured as specified in accordance with 3.2.4, shall not exceed 130 percent of the initial requirement. c. The lea

23、kage current, when measured as specified in 3.2.5, except, 10 minutes after reaching rated working voltage, shall not exceed 200 percent of the initial requirement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DA

24、YTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 5 3.4 Physical characteristics. 3.4.1 Terminal strength. Mounting terminals shall withstand the torque pressure shown below when applied in a clockwise direction in a plane perpendicular to the axis of the terminal for a period of 5 to

25、15 seconds. Number of Torque Screw thread threads (pound- Terminal engaged inches) Min Max No. 10-32 3 12.0 18.0 No. 10-32 6 20.0 25.0 3.5 Marking. Marking shall be in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2 with the manufacturers name or code and date code. 3.6 Rec

26、ycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life

27、cycle costs. 3.7 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.8 Workmanship. The capacitor shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VE

28、RIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A inspection of MIL-PRF-39018. Group B inspection shall be performed when specified o

29、n the purchase order. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements instead of performing group B tests (see 6.2c). 4.2.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-39018. 4.3

30、 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor

31、 may use their own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth herein where such inspections are deemed necessary to ensure su

32、pplies and services conform to prescribed requirements. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact th

33、e responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military Departments System Command. Packaging data retrieval is av

34、ailable from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYT

35、ON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 6 6. NOTES (This section contains information of a general or explanatory nature, which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do no

36、t exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists

37、and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the confor

38、mance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. d. Requirements for notification

39、 of change of product to acquiring activity, if applicable. e. Requirements for packaging and packing. 6.3 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor-prepared specification or drawing. 6.4 Similar vendor types. See table II. 6.5 U

40、sers of record. Coordination of this document for future revisions is coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post

41、 Office Box 3990, Columbus, OH 43218-3990 or emailed to capacitorfilterdscc.dla.mil also by telephone (614) 692-0563 or DSN 850-0563. 6.6 Suggested sources of supply. A suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use

42、 of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, P. O. Box 3990, Columbus, OH 43216-5000, by e-mail to capacitorfilterdscc.dla.mil, or by telephone (614) 692-0563 or DSN 850-0563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

43、,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 7 TABLE I. Electrical characteristics. DSCC drawing 89012- F Maximum ESR at 120 Hz, +25C (ohms) Maximum rms ripple current at 120 Hz, +85C (amperes) Case code 150 V dc working, 175 V dc surge 01

44、02 03 04 05 06 07 08 09 10 700 1,300 1,900 2,700 4,100 6,100 8,200 10,000 15,000 25,000 0.2983 0.1611 0.1117 0.0799 0.0536 0.0371 0.0319 0.0263 0.0221 0.0145 1.56 2.47 3.34 4.41 6.00 8.20 9.31 11.09 13.50 19.87 AA AB AC BB BC BF CD CF DF DJ 200 V dc working, 250 V dc surge 11 12 13 14 15 16 17 18 19

45、 20 470 930 1,300 1,800 2,800 4,200 5,600 7,200 10,000 18,000 0.3398 0.1739 0.1251 0.0915 0.0600 0.0410 0.0350 0.0280 0.0238 0.0153 1.46 2.38 3.15 4.12 5.67 7.80 8.89 10.75 13.01 19.34 AA AB AC BB BC BF CD CF DF DJ 250 V dc working, 300 V dc surge 21 22 23 24 25 26 27 28 29 30 340 680 990 1,300 2,00

46、0 3,000 4,100 5,300 7,800 12,000 0.4508 0.2260 0.1565 0.1196 0.0787 0.0535 0.0430 0.0340 0.0268 0.0175 1.27 2.09 2.82 3.60 4.95 6.83 8.02 9.76 12.26 18.08 AA AB AC BB BC BF CD CF DF DJ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONI

47、CS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89012 REV C PAGE 8 TABLE I. Electrical characteristics - Continued. DSCC drawing 89012- F Maximum ESR at 120 Hz, +25C (ohms) Maximum rms ripple current at 120 Hz, +85C (amperes) Case code 350 V dc working, 400 V dc surge 31 32 33 34

48、35 52 36 37 38 39 40 160 320 470 660 990 1,100 1,400 1,900 2,500 3,700 6,100 0.7841 0.3893 0.2659 0.1914 0.1281 0.1520 0.0911 0.0712 0.0550 0.0412 0.0259 0.96 1.59 2.16 2.85 3.88 4.08 5.23 6.23 7.67 9.88 14.86 AA AB AC BB BC CC BF CD CF DF DJ 450 V dc working, 525 V dc surge 41 42 43 44 45 46 47 48 49 50 51 99 190 270 380 570 860 1,100 1,400 2,000 2,