DLA DSCC-DWG-89029 REV A-2003 HOLDER ELECTRICAL CARD CARD GUIDE CONDUCTIVE PLASTIC ANTI-VIBRATION《电卡引导导电塑料抗振夹持器》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Added 15 new devices. Editorial changes throughout. 14 AUG 2003 Thomas M. Hess Prepared in accordance with ASME Y14.100 Selected item drawing REV PAGE REV A A A A A A A A A REV STATUS OF PAGES PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY James B. Walker Jr.

2、 DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 21 March 1989 CHECKED BY Bud Boulter TITLE HOLDER, ELECTRICAL CARD, CARD GUIDE, APPROVED BY Randy Larson CONDUCTIVE PLASTIC, ANTI-VIBRATION SIZE A CODE IDENT. NO. 14933 DWG NO. 89029 REV A PAGE 1 OF 9 A

3、MSC N/A 5998-E045 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

4、cense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of vibration and shock damping card guides intended to hold printed circuit boards and circuit card assemb

5、lies that are .050 to .100 inch (1.27 to 2.54 mm) thick. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 89029 Drawing number XX Dash number (see table I) B Color (B or W, see 3.3) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and hand

6、books. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplemen

7、t thereto, cited in the solicitation (see 6.2). STANDARDS DEPARTMENT OF DEFENSE MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Se

8、rvice (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those list

9、ed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). ASTM INTERNATIONAL (ASTM) ASTM D3935 Polycarbonate (PC) Unfilled and Reinforced Material. ASTM D4

10、066 Nylon Injection and Extrusion Materials (MA) (Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) (Non-Government Standards and other publications are normally available from the organizations which prepare

11、or which distribute the documents. These documents also my be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing

12、 in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The design, construction, and physical dimensions shall be as specified in table I and on figures 1, 2, 3, 4, 5, and 6. Provide

13、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 3 TABLE I. Dimensions of card holders. 1/ 2/ PIN 89029- Figure Mounting hole diameter (+.003, -.000 inch) (0.

14、08 mm) Dim. “L” Dim. “H” Dim. “A” Dim. “B” Dim. “C” Number of cantilevered grips 01 1 N/A 4.00 (101.6) N/A 3.50 (88.90) N/A N/A 2 02 1 N/A 6.00 (152.4) N/A 5.50 (139.70) N/A N/A 3 03 2 .130 (3.30) 3/ 2.500 (63.50) .180 (4.57) 2.200 (55.88) .087 (2.21) N/A 2 04 3 N/A 2.500 (63.50) .180 (4.57) 2.200 (

15、55.88) .087 (2.21) See 4/ 2 05 2 .130 (3.30) 3/ 2.500 (63.50) .270 (6.86) 2.200 (55.88) .100 (2.54) N/A 2 06 3 N/A 2.500 (63.50) .270 (6.86) 2.200 (55.88) .100 (2.54) See 4/ 2 07 2 .130 (3.30) 3/ 3.500 (88.90) .185 (4.70) 3.000 (76.20) .065 (1.65) N/A 2 08 3 N/A 3.500 (88.90) .185 (4.70) 3.000 (76.2

16、0) .065 (1.65) See 4/ 2 09 2 .130 (3.30) 3/ 4.125 (104.76) .180 (4.57) 3.625 (92.08) .087 (2.21) N/A 3 10 3 N/A 4.125 (104.76) .180 (4.57) 3.625 (92.08) .087 (2.21) See 4/ 3 11 4 .130 (3.30) 3/ 4.125 (104.76) .220 (5.59) 3.625 (92.08) .073 (1.85) N/A 3 12 5 N/A 4.125 (104.76) .220 (5.59) 3.625 (92.0

17、8) .073 (1.85) See 4/ 3 13 2 .130 (3.30) 3/ 5.500 (139.70) .220 (5.59) 5.000 (127.00) .087 (2.21) N/A 4 14 3 N/A 6.375 (161.93) .185 (4.70) 5.975 (151.77) .087 (2.21) See 4/ 5 15 2 .130 (3.30) 3/ 6.375 (161.93) .185 (4.70) 5.975 (151.77) .087 (2.21) N/A 5 16 2 .191 (4.85) 5/ 6.875 (174.63) .218 (5.5

18、4) 6.375 (161.93) .087 (2.21) N/A 5 17 6 .130 (3.30) 3/ 7.000 (177.80) .218 (5.54) 6.500 (165.10) .087 (2.21) N/A 4 1/ Dimensions are in inches. Metric equivalents (in parenthesis) are given for information only. 2/ Unless otherwise specified, tolerances for shall be .010 inch (0.25 mm) for all dime

19、nsions under 6.00 inch (152.4 mm) and .020 (0.51 mm) for all dimensions over 6.00 inch (154.2 mm). 3/ Mounting panel thickness shall be .060 to .070 inch (1.5 to 1.8 mm). 4/ Dimension C shall be .125 +.005, -.000 inch (3.18 +0.13 mm) diameter, counter bore .290 inch (7.37 mm) diameter by .038 inch (

20、9.65 mm) deep (2 places). 5/ Mounting panel thickness shall be .070 to .090 inch (1.77 to 2.29 mm). 3.2 Material. Material shall be nylon in accordance with ASTM D4066 (for dash numbers 01 and 02) or conductive polycarbonate in accordance with ASTM D3935 (for dash numbers 03 through 17). 3.3 Color.

21、Card holders shall be either black or white. Card holders fabricated of conductive polycarbonate are black and shall include a suffix “B” in the PIN. Card holders fabricated of nylon are white and shall include a suffix “W” in the PIN (see 1.2). Provided by IHSNot for ResaleNo reproduction or networ

22、king permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 4 3.4 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.5 Marking

23、. Marking of the card holder is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled, recovered, or environm

24、entally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship.

25、 Card guides shall be free of flash, pits, voids, and excessive mold marks. Visible parting line is acceptable. 4. VERIFICATION 4.1 Conformance inspections. 4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface an

26、d physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in 4.1.5. 4.1.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of

27、product for delivery (see 6.2.b). 4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.1.5. TABLE II. Sampling plan. Lot size Normal Tightened

28、2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 and over 29 35 4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct

29、 the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied

30、 to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. 4.1.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when

31、outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. Provided by IHSNot for ResaleNo reproduction or networking permitt

32、ed without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 5 Inches mm Inches mm Inches mm Inches mm .015 .035 .040 0.38 0.89 1.02 .070 .085 .109 1.78 2.16 2.77 .120 .125 .132 3.05 3.18 3.35 .25 .47 1.00 6.35 11.94 25.4 NOTES:

33、1. Dimensions are in inches. Metric equivalents are given for general information only. 2. See table I for A and B dimensions and tolerances. FIGURE 1. Two mounting button design and dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

34、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 6 Inches mm Inches mm .040 1.02 .469 11.91 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. See table I for L, H, A, B, and C dimensions and tolerances. FIGUR

35、E 2. Two mounting button design and dimensions (2 cantilevered grips shown). Inches mm Inches mm .040 1.02 .469 11.91 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. See table I for L, H, A, B, and C dimensions and tolerances. FIGURE 3. Rivet or bolt

36、 mounting design and dimensions (5 cantilevered grips shown). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 7 Inches mm Inches mm .040 1.02 .472 11.

37、99 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. See table I for L, H, A, B, and C dimensions and tolerances. FIGURE 4. Two mounting button design and dimensions (3 cantilevered grips shown). Inches mm Inches mm .040 1.02 .472 11.99 NOTES: 1. Dimen

38、sions are in inches. Metric equivalents are given for general information only. 2. See table I for L, H, A, B, and C dimensions and tolerances. FIGURE 5. Rivet or bolt mounting design and dimensions (3 cantilevered grips shown). Provided by IHSNot for ResaleNo reproduction or networking permitted wi

39、thout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 8 Inches mm Inches mm .040 1.02 .469 11.91 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. See table I for L, H, A, B, and

40、C dimensions and tolerances. FIGURE 6. Three mounting button design and dimensions (4 cantilevered grips shown). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be perfo

41、rmed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military D

42、epartments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature w

43、hich may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when performance specifications do not exist and qualified devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract

44、 or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for pack

45、aging and packing. 6.3 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Colum

46、bus, ATTN: DSCC/VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at “5998.Documentsdla.mil” or by facsimile (614) 692-6939 or DSN 850-6939. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMB

47、US, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89029 REV A PAGE 9 6.4 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact: Defense Supply Center, Columbus, ATTN: DSCC-V

48、AC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail “5998_Documentsdscc.dla.mil” or by facsimile (614) 692-6939 or DSN 850-6939. DSCC drawing PIN (1) Vendor similar designation or type number Vendor CAGE Vendor name and address 89029-03B 89029-04B 89029-05B 89029-06B 89029-07B 89029-08B 89029-09B 89029-10B 89029-11B 89029-12B 89029-13B 89029-14B 89029-15B 89029-16B 89029-17B ED5250 ED5250-CB ED52504 ED5250-4CB ED5350 ED5350-CB ED5412 ED5412-CB ED5413 ED5413-CB ED5550 ED5637 ED5638 ED5687 ED5700 07556 UNITRACK Industries Inc. 967 Masten Circle Millford, DE 19963-1085 TEL: