DLA DSCC-DWG-89031 REV C-2001 CONNECTOR ELECTRICAL PLUG COAXIAL RADIO FREQUENCY SERIES TNC PIN CONTACT FOR M17 152-00001《系列TNC插针接触件同轴射频插头连接器 用于M17 152-00001》.pdf

1、REVISIONSLTR DESCRIPTION DATE APPROVEDA Add source 00795. Format changes. 27 Mar 1990 CottongimB Incorporate NOR. 2 Aug 1993 Randy LarsonC Part number and source update. Editorial changes throughout. 14 June 2001 Robert HeberPrepared in accordance with MIL-STD-100REVPAGEREVCCCCCCCREV STATUSOF PAGES

2、PAGE 1234567PREPARED BYPMIC N/ARon GaryDEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OHIO 43216-5000CHECKED BY TITLEC. W. KoellerAPPROVED BYRichard MarbaisCONNECTOR, ELECTRICAL, PLUG, COAXIAL, RADIOFREQUENCY, SERIES TNC, PIN CONTACT, FORM17/152-00001SIZE CAGE CODE037Z3DWG. NO.89031Original date ofdrawing

3、12 July 1989AREV C PAGE 1 OF 7AMSC N/A 5935-E641-08DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBU

4、S, OH 43216-5000AREVCPAGE2FIGURE 1. General configuration.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVCPAGE3NOTES:1. A polyolefin sleeve in accordance with

5、MIL-I-23053/5 shall be supplied with each part.2. Dimensions are in inches.3. Metric equivalents are given for general information only.4. Metric equivalents are in parentheses.5. Dimension .650 (16.51 mm) is the largest overall diameter of the connector.6. Wrench flats to accommodate standard wrenc

6、h opening in accordance with FED-STD-H28, appendix 10.7. All undimensioned pictorial configurations are for reference purposes only.8. Dimension 2.00 maximum defines the overall length of the connector when assembled to the cable.9. No special tools shall be required for assembly to cables.10. Assem

7、bly of these connectors shall be in accordance with MIL-PRF-39012, category C. The shield terminationshall be accomplished using the M22520/5-01 basic crimp tool with die M22520/5-37, closure B. The centercontact shall be soldered.11. Connector coupling nuts and bodies shall be passivated in accorda

8、nce with ASTM-A967 or SAE-AMS-QQ-P-35.12. Series TNC pin contact in accordance with MIL-STD-348.13. Gasket material shall be Viton A or equivalent (Viton A is a brand name of E.I. DuPont).FIGURE 1. General configuration Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted w

9、ithout license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVCPAGE4Inches mm.010.156.343.437.5930.253.968.7111.1015.06NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.FIGURE 2. Cable strip dimensio

10、ns.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVCPAGE5ENGINEERING DATA:Nominal impedance: 50 ohms.Frequency range: DC to 11 GHz.Voltage rating: 500 volts rms

11、 maximum at sea level;125 volts rms at 70,000 feet.Operating temperature: -65C to +165C.REQUIREMENTS: (The requirements of DSCC drawing 84148 are applicable.)Dimensions and configurations: See figure 1 herein and MIL-STD-348.Force to engage and disengage: 2 inch-pounds maximum torque (.225 Nm).Coupl

12、ing proof torque: 15 inch-pounds minimum (1.69 Nm).Hermetic seal: Not applicable.Leakage: Not applicable.Center contact retention: 6 pounds minimum axial force (26.69 N).Voltage standing wave ratio (VSWR): The VSWR, when measured in accordance with MIL-PRF-39012 over afrequency range of 500 MHz to 1

13、1 GHz, or approximately 80 percent of the cables upper cutoff frequency, whicheveris lower, shall not exceed 1.30:1 when measured at 50 ohms.Moisture resistance: Method 106 of MIL-STD-202, except no measurement at high humidity. Insulation resistanceshall be at least 200 megohms within 5 minutes aft

14、er removal from humidity chamber.Insulation resistance: Methods 302, test condition B of MIL-STD-202, 5,000 megohms, minimum.Connector durability: 500 cycles minimum, at 12 cycles per minute maximum. The connector shall meet the matingcharacteristics and force to engage and disengage requirements.Di

15、electric withstanding voltage: 1,500 V rms, in accordance with method 301 of MIL-STD-202, minimum at sea level.Random vibration: Method 2005, test condition V, test level F of MIL-STD-1344.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE

16、 DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVCPAGE6Contact resistance (in milliohms maximum):Initial After environmentalCenter contact: (89031TBS) 1.5 1.5Center contact: (89031 TBS-1) 2.0 2.0Outer contact: 0.2 N/AOuter cable braid to body: 0.1 N/AVibration, high frequ

17、ency: Method 204, test condition B of MIL-STD-202, except the method of mounting shall beapproved by DSCC-VQ. No discontinuity shall be permitted.Shock: MIL-STD-202, test condition I of method 213.Thermal shock: MIL-STD-202, test condition B of method 107 except test high temperature shall be +200C.

18、Corona level: 375 V rms, at 70,000 feet (21.336 km).Altitude: The connector shall operate as specified herein at altitudes up to and including 70,000 feet (21.336 km).Salt spray: Method 101, test condition B of MIL-STD-202.RF high potential withstanding voltage: 1,000 V rms, minimum.Frequency: 5 to

19、7.5 MHz.Leakage current: Not applicable.Coupling mechanism retention force: 100 pounds, minimum (444.8 N).RF leakage: -60 dB, minimum tested between 2 and 3 GHz.RF insertion loss:89031TBS 0.06 F(GHz) dB maximum from 3 to 9 GHz89031TBS-1 0.07 F(GHz) dB maximum from 3 to 6 GHzCable accommodation: M17/

20、152-00001.Cable retention force: 10 pounds, minimum axial force (44.5 N).Part of Identifying Number (PIN): 89031TBS and 89031TBS-1.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89031DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS

21、, OH 43216-5000AREVCPAGE7Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as theybecome available. The vendors listed herein have agreed to this drawing and a certificate of compliance has beensubmitted to DSCC-VAI.DSCC drawingPIN1/VendorCAGE

22、NumberVendorreferencePIN89031TBS 00795950771202100A00E-0004000-007889031TBS-1 00795950771206100A00E-0004093-00181/ Parts must be purchased to this DSCC PIN to assure thatall performance requirements and tests are met.Vender CAGE Vendor namenumber and address00795 Delta Electronics416 Cabot StreetBeverly, MA 0191595077 Solitron/Vector Microwave Products3301 Electronics WayWest Palm Beach, FL 33407Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-