DLA DSCC-DWG-89074 REV D-2006 CONNECTOR ELECTRICAL INSERT ARRANGEMENT MINIATURE FOUR SIZE 20 SIGNAL CONTACTS WITH ONE SIZE 8 CONTACT CAVITY《插入管理微型四号20次信号接触带一号8次接触能力的连接器》.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5935-R021-92. For CAGE 28198, add additional DESC part numbers and corresponding vendor part number. 92-05-08 James P. Donohue B Change “part number” to “Part or Identifying Number (PIN)”. Editorial changes throughout. 93-10-27

2、 James P. Donohue C Vendor CAGE 60563, PINs, delete and substitute new PINs. Editorial changes throughout. 01-01-22 Robert M. Heber D Add Vendor CAGE SW884, delete MIL-STD-1344 test methods, add EIA-364 test procedures 06-01-20 Richard L. Taylor Prepared in accordance with ASME-Y14.100 REV PAGE REV

3、D C C D D D REV STATUS OF PAGES PAGE 1 2 3 4 5 6 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Carl Dello-Stritto APPROVED BY Charles W. Koeller CONNECTOR, ELECTRICAL, INSERT ARRANGEMENT, MINIATURE, FOUR SIZE 20 SIGNAL CONTACTS, WITH ON

4、E SIZE 8 CONTACT CAVITY SIZE CAGE CODE 037Z3 DWG. NO.89074 Original date of drawing 31 July 1990 A REV D PAGE 1 OF 6 AMSC N/A 5935-E769-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Engaging face (pin) Inches mm .056 .112

5、 .162 .216 . 1.42 2.84 4.11 5.49 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance for three place decimals is .005 inch (0.13 mm). 4. All dimensions are true position (TP). 5. Contact holes in insert shall be located o

6、n TP within a .005 inch (0.13 mm) diameter circle. 6. Markings are shown for the pin insert front. Socket inserts are the opposite. 7. Reference documents shall be of the issue in effect on date of invitations for bid. FIGURE 1. Insert arrangement-four size 20 signal contacts with one size 8 contact

7、 cavity. 037Z3 89074 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVC PAGE2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. ENGINEERING DATA: Voltage rating: 500 volts rms at sea level. Operating temperature: -55C

8、 to +125C. REQUIREMENTS: Requirements of drawing 85039 and MIL-DTL-24308 are applicable. Dimensions and configurations: See figure 1. Signal contact specifications: Style A (crimp removable signal contacts): Socket: M39029/63-368. in: M39029/64-369. Style B (solder fixed signal contacts): Socket: MI

9、L-DTL-24308, Appendix B, figure B-1. Pin: MIL-DTL-24308, Appendix B, figure B-2. Shell size: One. Shell specifications: Style A: Socket: MIL-DTL-24308/2, figure 1. Pin: MIL-DTL-24308/4, figure 1. Style B: Socket: MIL-DTL-24308/1, figure 1. Pin: MIL-DTL-24308/3, figure 1. Tools: Connectors with crimp

10、 removable signal contacts shall be designated for contact insertion and removal with the applicable military tool as follows: Contact size Tool PIN20 M81969/39 - 01 with plastic tip M81969/1-02 with metal tip 037Z3 89074 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVC PAGE3 Provided

11、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Mating and unmating forces (with signal contacts only installed): See table I. TABLE I. Mating and unmating forces. Mating force (pounds) Unmating force (pounds) Contact type Minimum Maxim

12、um Minimum Maximum Signal 0.154 2.61 0.154 1.54 Contact resistance: See table II. TABLE II. Contact resistance (millivolts maximum). 1/ Contact classes G, D, M, N Contact Size AWG wire Size Test current (amperes) After salt spray All others 20 24 20 3.0 7.5 55 65 45 55 1/ Not applicable to crimp or

13、shielded contacts. Dielectric withstanding voltage: See table III. TABLE III. Dielectric withstanding voltage. Altitude Humidity condition All other conditions Sea level 600 1,000 70,000 - 325 Vibration: Test procedure EIA364-28, test condition IV. Temperature cycling: Test procedure EIA364-32, cond

14、ition 1, 5 cycles, except temperature shall be -55C to +125C. 037Z3 89074 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Approved sources of supply are liste

15、d herein. Additional sources will be added as they become available. The vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor similar PIN 1/ DSCC drawing PIN 2/ 3/ 4/ 5/ CAGE 71468 CAGE 60563 CAGE 28198 CAGE SW8

16、84 89074DAEPT 89074DAEST 89074DAEPR 89074DAESR CBC5W1M1F000-50-799.2 CBC5W1F1F000-50-799.2 CBC5W1M10000-50-799.0 CBC5W1F10000-50-799.0 89074GAEPT 89074GAEST 89074GAEPR 89074GAESR CBC5W1M1F00C-50 CBC5W1F1F00C-50 CBC5W1M1000C-50 CBC5W1F1000C-50 89074GBEPT 89074GBEST 89074GBEPR 89074GBESR DEMMY5W1PA101

17、 DEMMY5W1SA101 DEMM5W1PA101 DEMM5W1SA101 P51PSA2D P51RSA2D P51PSA2 P51RSA2 CBM5W1M02F00C-0 CBM5W1F02F00C-0 CBM5W1M02000C-0 CBM5W1F02000C-0 89074NAEPT 89074NAEST 89074NAEPR 89074NAESR CBC5W1M1F00C-50-403.0 CBC5W1F1F00C-50-403-0 CBC5W1M1000C-50-403.0 CBC5W1F1000C-50-403.0 PEMMHW5W1P PAMMHW5W1S PAMMW5W

18、1P PAMMW5W1S 89074MAEPT 89074MAEST 89074MAEPR 89074MAESR CBC5W1M1F000-50-403.4 CBC5W1F1F000-50-403.4 CBC5W1M10000-50-403.3 CBC5W1F10000-50-403.3 85040MAEPT 85040MAEST 85040MAEPR 85040MAESR CBC7W2M1F000-50-403.4 CBC7W2F1F000-50-403.4 CBC7W2M10000-50-403-4 CBC7W2F10000-50-403-4 1/ Caution. Do not use

19、this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 2/ Connectors supplied to this drawing shall include a full complement of signal contacts. 3/ Size 8 contacts should be ordered separately. 4/ Size 8 contacts are snap-in and

20、 removable. 5/ For size 8 contacts, see DSCC drawings 89046 through 89061. 037Z3 89074 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. Vender CAGE Vendor name

21、 number and address 28198 Positronics Industries, Incorporated 423 North Campbell Springfield, MO 65801-8247 60563 The Phoenix Company 555 Pond Drive Wood Dale, IL 60191-1192 71468 ITT Cannon P.O. Box 929 666 East Dyer Road Santa Ana, CA 92702-0929 SW884 The Phoenix Company of Chicago, Mexico Carretera Internacional K M 1969 Guadalajara Nogales KM 2 Empalme, Mexico 85340 037Z3 89074 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVD PAGE6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-