DLA DSCC-DWG-90091 REV F-2009 RELAY SOLID STATE HERMETICALLY SEALED OPTICALLY ISOLATED 1 OR 2 A WITH OR WITHOUT CIRCUIT-BREAKER ACTION OR STATUS INDICATION 6-PIN CERAMIC DUAL-IN-LI.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Changes in accordance with NOR 5945-R003-92. 91-11-13 D.E. Moore B Changed CAGE 63745 to CAGE 16170. PINs 90091-001, 90091-003, 90091-005, and 90091 -007 are obsolete. Updated to current requirements of MIL-R-28750C. Editorial changes throughout. 95-03-28 E

2、. Back C Added as an approved source of supply CAGE 58614, part numbers DS13-1002, DS13-1000, DS13-1001, DS13-1Y for DESC PIN 90091-002, -004, -006, -008 respectively. 98-07-01 David E. Moore D Corrected dimension on package height to be .155 MAX instead of .115 MAX. Update to current requirements o

3、f MIL-PRF-28750D. Editorial changes throughout. 00-01-07 Kendall A. Cottongim E Change the turn off time from 0.25 ms maximum to 0.5 ms maximum (paragraph 3.3.3.8). Validation and update 04-14-05 Kendall A. Cottongim F Incorporated boilerplate updates. Modified approved sources of supply information

4、. 09-07-06 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source Control drawing REV STATUS OF PAGES REV F F F F F F F F F F F F F PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Tony J. Westphal DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH 43444-5000 Original

5、date of drawing: 21 December 1990 CHECKED BY R. Gosciniak TITLE RELAY, SOLID STATE, HERMETICALLY SEALED, OPTICALLY ISOLATED, 1 OR 2 A, WITH OR WITHOUT CIRCUIT-BREAKER ACTION OR STATUS INDICATION, 6-PIN CERAMIC DUAL-IN-LINE PACKAGE APPROVED BY Randy Larson SIZE A CODE IDENT. NO. 037Z3 DWG NO. 90091 R

6、EV F PAGE 1 OF 13 AMSC N/A 5945-E140CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH

7、IO SIZE A CODE IDENT NO. 037ZE DWG NO. 90091 REV F PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of sealed, solid state relays, supplied to the “Y” screening requirements of MIL-PRF-28750. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 9

8、0091 002 | | | |_ Drawing Dash number number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for addit

9、ional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.

10、2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICA

11、TIONS MIL-PRF-28750 - Relays, Solid State, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts. MIL-STD-704 - Aircraft Electric Power Characteristics. MIL-STD-883 - Test Methods and Procedures for Microelectronics. (Copi

12、es of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the extent spe

13、cified herein. Unless otherwise specified, the issues of the documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B488 - Electrodeposited Coatings of Gold for Engineering Uses. (Application for copies is available online at http:/www.astm.

14、org/or should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19482-2959.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited her

15、ein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY C

16、ENTER DAYTON, OHIO SIZE A CODE IDENT NO. 037ZE DWG NO. 90091 REV F PAGE 3 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-28750, and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be

17、as specified in MIL-PRF-28750, and on figure 1 herein. 3.2.1 PIN and features. See table I. 3.3 Electrical characteristics. Unless otherwise specified, ambient temperature for electrical characteristics shall be -55C to +105C. Unless otherwise specified, input voltage for functional tests or bias sh

18、all be 5 V dc. 3.3.1 Input characteristics. Open collector TTL or direct control (see figure 2, configuration B). 3.3.1.1 Input supply range. 3.8 V dc minimum to 6.0 V dc maximum. 3.3.1.2 Input (bias) current. 15 mA maximum at Vbias= 5 V dc (see figure 3). 3.3.1.3 Turn-off voltage (assured). 1.5 V d

19、c maximum. 3.3.1.4 Turn-on voltage (assured). 3.8 V dc minimum. 3.3.1.5 Reverse polarity voltage. 2 mA maximum leakage current at -32 V dc (pin 1 reference to pins 2 and 8). 3.3.2 Input (control) characteristics. CMOS or open collector TTL (see figure 2, configuration A). Unless otherwise specified,

20、 input voltage for functional tests is 5 V dc. This only applies if used as shown on figure 4. 3.3.2.1 Control current. 250 A maximum at 5 V dc and 1 mA maximum at 18 V dc (when status is not used). 250 A maximum at 5 V dc (when status is used). 3.3.2.2 Control voltage range. 0 V dc minimum to 18 V

21、dc maximum (when status is not used). 0 V dc minimum to 6 V dc maximum (when status is used). 3.3.2.3 Turn-off voltage (assured). 3.2 V dc minimum. 3.3.2.4 Turn-on voltage (assured). 0.3 V dc maximum. 3.3.3 Output characteristics. 3.3.3.1 Continuous operating output voltage. 60 V dc maximum. 3.3.3.2

22、 Continuous load current. For 90091-002 and 90091-004, see figure 5. For 90091-006 and 90091-008, see figure 6. 3.3.3.3 Output voltage drop. 0.6 V dc maximum for 90091-002 and 90091-004, and 0.75 V dc maximum for 90091-006 and 90091-008. 3.3.3.4 Output leakage current. 40 A maximum at 60 V dc. 3.3.3

23、.5 Transient blocking voltage. 80 V dc maximum in accordance with MIL-STD-704 (28 V dc systems). 3.3.3.6 “ON“ resistance. 0.45 ohm maximum for 90091-002 and 90091-004 and 0.22 ohm maximum for 90091-006 and 90091-008 with Iload= 100 mA and TJ= 25C. Provided by IHSNot for ResaleNo reproduction or netw

24、orking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 037ZE DWG NO. 90091 REV F PAGE 4 3.3.3.7 Turn-on time. 1.5 ms maximum (see figure 7). 3.3.3.8 Turn-off time. 0.5 ms maximum (see figure 7). 3.3.3.9 Exponential rate of voltage rise (dv/

25、dt). 100 volts per microsecond minimum in accordance with MIL-PRF-28750. 3.3.3.10 Electrical system spike. 600 V dc minimum in accordance with MIL-STD-704 (28 V dc systems). 3.3.3.11 Output capacitance. 475 pF maximum at 100 kHz and 25 V dc. 3.3.3.12 Input-to-output capacitance. 10 pF maximum. 3.3.3

26、.13 Dielectric withstanding voltage. 1,000 V ac minimum (input-to-output, and all pins to case). 3.3.3.14 Insulation resistance. 1,000 M at 500 V dc. 3.3.3.15 Status. Applicable to 90091-002 and 90091-006 only. See table II. 3.3.3.15.1 Status supply voltage. 30 V dc maximum. 3.3.3.15.2 Status leakag

27、e current. 4 A maximum at 15 V dc. 3.3.3.15.3 Status (sink) current. 2.0 mA maximum with Vso(Vstatus- 0.3 V) / (Istatus), where Istatus 2 mA. Inductive loads must be diode suppressed. Input transitions should be 1 ms duration and the input drive should be a bounceless contact type. FIGURE 7. Turn-on

28、 and turn-off timing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 037ZE DWG NO. 90091 REV F PAGE 12 FIGURE 8. Typical overload versus trip time at ambient temperature. 5. PACKAG

29、ING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain pac

30、kaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agen

31、cys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. . Relays conforming to this drawing are intended for use

32、when military specifications do not exist and qualified military devices that will perform the required function are not available for O.E.M. application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listing. W

33、hen a military specification exists and the product covered by this drawing has been qualified for listing on QPL-28750, this drawing will become inactive for new design. The QPL-28750 product will be the preferred item for all applications. Provided by IHSNot for ResaleNo reproduction or networking

34、 permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 037ZE DWG NO. 90091 REV F PAGE 13 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the co

35、nformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit ti

36、n whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of

37、tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.4 Notes. Only definitions of the notes specified in MIL-PRF-28750 will app

38、ly to this drawing. 6.5 Supersession data. PIN 90091-001, 90091-003, 90091-005, and 90091-007 have been superseded by PIN 90091-002, 90091-004, 90091-006, and 90091-008, respectively. 6.6 Replaceability. Relays covered by this drawing will replace the same generic device covered by a contractor-prep

39、ared specification or drawing. 6.7 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto:relaydla

40、.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. 6.8 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become a

41、vailable. Assistance in the use of this drawing may be obtained online at mailto:relaydla.mil, or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. DSCC drawing PIN Vendor similar designation o

42、r type number 1/ Vendor CAGE Vendor name and address 90091-002 90091-004 90091-006 90091-008 CD21CDY CD20CDY CD01CFY CD00CFY 16170 Teledyne Electronic Technologies 12964 Panama Street Los Angeles, CA 90066-6534 Phone (310) 822-8229 90091-002 90091-004 90091-006 90091-008 DS13-1002 DS13-1000 DS13-100

43、1 DS13-1Y 18741 Tyco Electronics Corporation/Kilovac Division 550 Linden Avenue Carpinteria, CA 93013-2038 Phone: (800) 806-0480 Plant: Philip Engineering Corporation 3 Peerless Way, Unit C Enfield, CT 06082-2371 Phone: (800) 806-0480 1/ Part must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-