DLA DSCC-DWG-92025 REV D-2013 CONNECTORS RECEPTACLE ELECTRICAL PWB TERMINATION ( 062 TO 093) DOUBLE ROW TOP ENTRY 100 CENTERS 025 POSTS.pdf

1、REVISIONS LTR DSCCRIPTION DATE APPROVED A Change CAGE 14933 to 037Z3. Replace MIL-G-45204 with ASTM B488. Editorial changes throughout. 05/14/02 Robert M. Heber B Updating references and CAGE (8N187) Part or Identifying Numbers (PIN) 8/17/09 Abdo M. Abdouni C Update vendor CAGE OAKZ5 name and addres

2、s. Editorial changes throughout. 6 June 2011 Howard Jenkins D Page 2, figure 1, recommended board layout, change termination hole from .035 .003 to .040 min. Page 5 add MIL-DTL-45204. 7 July 2013 Abdo M. Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV PAGE REV ST

3、ATUS OF PAGES REV D D C C D C C C PAGE 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 William Carpenter Original date of drawing 1 July 1994 CHECKED BY TITLE James P. Donohue CONNECTORS, RECEPTACLE, ELECTRICAL, PWB TERMINATION (.062 TO .093), DOUBLE RO

4、W, TOP ENTRY, .100 CENTERS, .025 POSTS APPROVED BY Randy Larson SIZE CAGE CODE DWG. NO. 92025 A 037Z3 REV D PAGE 1 OF 8 AMSC N/A 5935-E850-001 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or

5、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV D PAGE 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerances shall be .00

6、5 inch ( 0.13 mm). 4. Contact design is optional. 5. Position of contact tail is optional provided it has a minimum thickness of .006 inch (0.15 mm) and a typical reference width of .030 inch (0.76 mm). FIGURE 1. Dimensions and configurations. Inches mm .003 0.08 .004 0.10 .010 0.25 .013 0.33 .015 0

7、.38 .025 0.64 .034 0.86 .040 1.02 .047 1.19 .100 2.54 .135 3.43 .220 5.59 .325 8.26 .040 MIN Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV C PAGE 3 Dim

8、ensions A and B. 1/ 2/ Dash numbers Dimension A center to center Dimension B overall length Number of contacts Inches mm Inches mm 01 .000 0.00 .100 2.54 2 02 .100 2.54 .200 5.08 4 03 .200 5.08 .300 7.62 6 04 .300 7.62 .400 10.16 8 05 .400 10.16 .500 12.70 10 06 .500 12.70 .600 15.24 12 07 .600 15.2

9、4 .700 17.78 14 08 .700 17.78 .800 20.32 16 09 .800 20.32 .900 22.86 18 10 .900 22.86 1.000 25.40 20 11 1.000 25.40 1.100 27.94 22 12 1.100 27.94 1.200 30.48 24 13 1.200 30.48 1.300 33.02 26 14 1.300 33.02 1.400 35.56 28 15 1.400 35.56 1.500 38.10 30 16 1.500 38.10 1.600 40.64 32 17 1.600 40.64 1.70

10、0 43.18 34 18 1.700 43.18 1.800 45.72 36 19 1.800 45.72 1.900 48.26 38 20 1.900 48.26 2.000 50.80 40 21 2.000 50.80 2.100 53.34 42 22 2.100 53.34 2.200 55.88 44 23 2.200 55.88 2.300 58.42 46 24 2.300 58.42 2.400 60.96 48 25 2.400 60.96 2.500 63.50 50 26 2.500 63.50 2.600 66.04 52 27 2.600 66.04 2.70

11、0 68.58 54 28 2.700 68.58 2.800 71.12 56 29 2.800 71.12 2.900 73.66 58 30 2.900 73.66 3.000 76.20 60 31 3.000 76.20 3.100 78.74 62 32 3.100 78.74 3.200 81.28 64 33 3.200 81.28 3.300 83.82 66 34 3.300 83.82 3.400 86.36 68 35 3.400 86.36 3.500 88.90 70 36 3.500 88.90 3.600 91.44 72 37 3.600 91.44 3.70

12、0 93.98 74 38 3.700 93.98 3.800 96.52 76 39 3.800 96.52 3.900 99.06 78 40 3.900 99.06 4.000 101.60 80 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking per

13、mitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV C PAGE 4 TABLE I. Contact finishes. PIN designator Contact PC Tail plating B Tin/lead Tin/lead C 30 microinches gold (0.76 m) Tin/lead D 50 microinches gold (1.27 m) T

14、in/lead E Tin/lead Hot tin dipped TABLE II. Number of positions. Dash numbers Number of positions Dash numbers Number of positions 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 2X1 2X2 2X3 2X4 2X5 2X6 2X7 2X8 2X9 2X10 2X11 2X12 2X13 2X14 2X15 2X16 2X17 2X18 2X19 2X20 21 22 23 24 25 26

15、27 28 29 30 31 32 33 34 35 36 37 38 39 40 2X21 2X22 2X23 2X24 2X25 2X26 2X27 2X28 2X29 2X30 2X31 2X32 2X33 2X34 2X35 2X36 2X37 2X38 2X39 2X40 TABLE III. Temperature range. PIN Designator Temperature range C Blank -40 to +105 M -55 to +125 H -65 to +220 Provided by IHSNot for ResaleNo reproduction or

16、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV D PAGE 5 REQUIREMENTS: Shall meet the requirements of drawing number 92024. Design and construction: Dimensions and configurations: See figure 1, and ta

17、bles I, II, and III. Materials: Housing: The insulator shall be glass-mineral-filled nylon in accordance with ASTM D4066 or glass filled thermoplastic in accordance with ASTM D5927 or MIL-M-24519. All plastic shall be rated V-0 in accordance with UL-94. Contact body: Copper alloy in accordance with

18、C770, 1/4 hard brass or beryllium copper. Spring: Heat treated beryllium copper. NOTE: When contact body and spring are an integral part of the contact design they shall be of the same material. Plating: See table I for contact and tail platings. Spring: Gold flash on spring in accordance with MIL-D

19、TL-45204, grade C, type II, 10 micro inches minimum or equivalent. Electrical: Body: Dielectric withstanding voltage: 1,250 volts rms, 60 Hz at sea level. Contact: Maximum current rating: 3 amperes rms at sea level. Environmental: Operating temperature range: See table III. Resistance to soldering h

20、eat: Only applicable to “H” temperature range, see table III. Mechanical: Body: Contact retention: 1.5 pounds (0.68 kg) minimum, per position. Contact: Durability: 50 cycles (mating and unmating). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFEN

21、SE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV C PAGE 6 Interface: Mates to .025 inch (0.64 mm) square pin on .100 inch (2.54 mm) true centers. See DSCC drawings 89042, 86102, and 92023. Mating pin length: .190 inch (4.83 mm) minimum, .240 inch (6.10 mm)

22、maximum. Printed circuit board: Board thickness: .062 to .093 inch. (1.57 to 2.36 mm). Hole pattern: See figure 1. Marking: The Part or Identifying Number (PIN) shall be marked on the package in accordance with MIL-STD-1285. The PIN shall include the complete DSCC PIN, manufacturers name or CAGE cod

23、e, and date code. The marking shall be permanent and legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed in the following format: 92025 X XX Z DSCC drawing Plating Number of positions Temp. range number (see table I) (see table II) designator (see table III) Provided b

24、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV C PAGE 7 Approved sources of supply are listed herein. Additional sources will be added as they become available. T

25、he vendors listed on the requirements drawing have agreed to this drawing and a certificate of compliance has been submitted to DLA Land and Maritime-VAI. DSCC PIN Vendors PIN 1/ Vendor CAGE OAKZ5 1/ Vendor CAGE 8N187 1/ 2/ Vendor CAGE 67720 1/ 3/ 4/ 92025-X-01Z 92025-X-02Z 92025-X-03Z 92025-X-04Z 9

26、2025-X-05Z 92025-X-06Z 92025-X-07Z 92025-X-08Z 92025-X-09Z 92025-X-10Z 92025-X-11Z 92025-X-12Z 92025-X-13Z 92025-X-14Z 92025-X-15Z 92025-X-16Z 92025-X-17Z 92025-X-18Z 92025-X-19Z 92025-X-20Z 92025-X-21Z 92025-X-22Z 92025-X-23Z 92025-X-24Z 92025-X-25Z 92025-X-26Z 92025-X-27Z 92025-X-28Z 92025-X-29Z 9

27、2025-X-30Z 92025-X-31Z 92025-X-32Z 92025-X-33Z 92025-X-34Z 92025-X-35Z 92025-X-36Z 92025-X-37Z 92025-X-38Z 92025-X-39Z 92025-X-40Z SATP025Z-X-02MIL SATP025Z-X-04MIL SATP025Z-X-06MIL SATP025Z-X-08MIL SATP025Z-X-10MIL SATP025Z-X-12MIL SATP025Z-X-14MIL SATP025Z-X-16MIL SATP025Z-X-18MIL SATP025Z-X-20MIL

28、 SATP025Z-X-22MIL SATP025Z-X-24MIL SATP025Z-X-26MIL SATP025Z-X-28MIL SATP025Z-X-30MIL SATP025Z-X-32MIL SATP025Z-X-34MIL SATP025Z-X-36MIL SATP025Z-X-38MIL SATP025Z-X-40MIL SATP025Z-X-42MIL SATP025Z-X-44MIL SATP025Z-X-46MIL SATP025Z-X-48MIL SATP025Z-X-50MIL SATP025Z-X-52MIL SATP025Z-X-54MIL SATP025Z-X

29、-56MIL SATP025Z-X-58MIL SATP025Z-X-60MIL SATP025Z-X-62MIL SATP025Z-X-64MIL SATP025Z-X-66MIL SATP025Z-X-68MIL SATP025Z-X-70MIL SATP025Z-X-72MIL SATP025Z-X-74MIL SATP025Z-X-76MIL SATP025Z-X-78MIL SATP025Z-X-80MIL 87606-302LF 87606-303LF 87606-304LF 87606-304LF 87606-305LF 87606-306LF 87606-307LF 87606

30、-308LF 87606-309LF 87606-310LF 87606-311LF 87606-312LF 87606-313LF 87606-314LF 87606-315LF 87606-316LF 87606-317LF 87606-318LF 87606-319LF 87606-320LF 87606-321LF 87606-322LF 87606-323LF 87606-324LF 87606-325LF 87606-326LF 87606-327LF 87606-328LF 87606-329LF 87606-330LF 87606-331LF 87606-332LF 87606

31、-333LF 87606-334LF 87606-335LF 87606-336LF - - - - *-121-02-2 *-121-04-2 *-121-06-2 *-121-08-2 *-121-10-2 *-121-12-2 *-121-14-2 *-121-16-2 *-121-18-2 *-121-20-2 *-121-22-2 *-121-24-2 *-121-26-2 *-121-28-2 *-121-30-2 *-121-32-2 *-121-34-2 *-121-36-2 *-121-38-2 *-121-40-2 *-121-42-2 *-121-44-2 *-121-4

32、6-2 *-121-48-2 *-121-50-2 *-121-52-2 *-121-54-2 *-121-56-2 *-121-58-2 *-121-60-2 *-121-62-2 *-121-64-2 *-121-66-2 *-121-68-2 *-121-70-2 *-121-72-2 *-121-74-2 *-121-76-2 *-121-78-2 *-121-80-2 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. 2/

33、 Vendor PIN covers “C” contact finish. 3/ Vendor PIN covers “Blank” and “M” temperatures only. 4/ Asterisks replaced by the number 6 for “B” and “E” contact finish, 36 for “C” contact finish, and 56 for “D” contact finish. For tin/lead pc tail use “-T” suffix in conjunction with prefix “E”. Provided

34、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 92025 REV C PAGE 8 Vendor CAGE Vendor name number and address OAKZ5 Muller-Crane 1280 Massillon Road Building G Suite 1500n Akron, OH 44306 67720 Cristek Interconnects, Incorporated 1301 South Lewis Street Anaheim, CA 92805-6431 8N187 T.T.I. 2601 Sylvania Cross Dr Fort Worth, TX 76137 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-