DLA DSCC-DWG-93038 REV C-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL 90 DEG INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES I AND II CONNEC.pdf

1、 NOTICE OF REVISION (NOR) This revision described below has been authorized for the document listed. 1. DATE (YYMMDD) 04-05-07 Form Approved OMB No. 0704-0188 Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, sear

2、ching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Def

3、ense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project (0704-0188), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLET

4、ED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING CONTRACTING OFFICER FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM.2. PROCURING ACTIVITY NO. 3. DODAAC 4. ORIGINATOR b. ADDRESS (Street, City, State, Zip Code)Defense Supply Center Columb

5、us 3990 East Broad Street Columbus, Ohio 43216-5000 5. CAGE CODE037Z3 6. NOR NO.5935-R035-03 a. TYPED NAME (First, Middle Initial, Last)Jeffery Tunstall 7. CAGE CODE037Z3 8. DOCUMENT NO.93038 9. TITLE OF DOCUMENT CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, 90 INDIVIDUAL AND/OR OVERA

6、LL SHIELD TERMINATION, (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS). 10. REVISION LETTER 11. ECP NO.N/A a. CURRENTB b. NEWC 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIESALL 13. DESCRIPTION OF REVISION Page 3, figure 1: Add Max cable range” column to accessory shell size table, as shown t

7、o the left. Max Cable Range 01 02 03 05 06 06 07 07 08 Page 5, Vendor CAGE number table Delete: “390HA005” and substitute: “390FA005”. a. (X one) X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this

8、 change. (3) Custodian of master document shall make above revision and furnish revised document. b. ACTIVITY AUTHORIZED TO APPROVE CHANGE FOR GOVERNMENTDSCC-VAI c. TYPED NAME (First, Middle Initial, Last)d. TITLECHIEF,INTERCONNECTION DEVICES e. SIGNATURERichard L. Taylor f. DATE SIGNED (04-05-07)15

9、a. ACTIVITY ACCOMPLISHING REVISIONDSCC-VAI b. REVISION COMPLETED (Signature)Jeffery Tunstall c. DATE SIGNED (04-05-07)DD Form 1695, APR 92 Previous editions are obsolete Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REVISIONS LTR DESCRIPTION DATE A

10、PPROVED A Correct “A” diameter. 15 Dec 94 Randy Larson B Update format. Correcting references. Correcting address list of sources. 16 July 02 Robert Heber Prepared in accordance with ASME Y14.100 REV PAGE REV B B B B B REV STATUS OF PAGES PAGE 1 2 3 4 5 PMIC N/A PREPARED BY Jeffery Tunstall DEFENSE

11、SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 CHECKED BY Abdo Abdouni APPROVED BY Robert Heber TITLE CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, 90 INDIVIDUAL AND /OR OVERALL SHIELD TERMINATION, CATEGORY 2A (FOR MIL-DTL-38999 SERIES I and II CONNECTORS) SIZE CAGE CODE 037Z3 DWG.

12、 NO. 93038 Original date of drawing 14 November 1994 A REV B PAGE 1 OF 5 AMSC N/A 5935-E678 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93038 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 2 90 C

13、ONFIGURATION FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93038 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 3 Accessory shell size A dia max G max H max

14、09 19.1 (0.75) 15.0 (.59) 64.8 (2.55) 11 21.6 (0.82) 16.8 (.66) 67.8 (2.67) 13 25.4 (1.00) 18.3 (.72) 68.4 (2.69) 15 29.2 (1.10) 20.6 (.81) 83.3 (3.28) 17 31.8 (1.25) 22.5 (.89) 85.6 (3.37) 19 35.6 (1.48) 24.8 (.98) 89.9 (3.54) 21 39.4 (1.50) 24.8 (.98) 89.9 (3.54) 23 41.9 (1.65) 28.6 (1.13) 94.2 (3

15、.71) 25 47.0 (1.75) 28.6 (1.13) 94.2 (3.71) Cable accommodation range Clamp size Min Max B max K max N max 01 3.99 (.157) 5.33 (.210) 19.30 (0.760) 21.4 (0.84) 16.0 (.63) 02 4.75 (.187) 7.92 (.312) 19.30 (0.760) 23.0 (0.91) 19.2 (.76) 03 7.14(.281) 11.13 (.438) 19.30 (0.760) 27.8 (1.09) 23.9 (.94) 0

16、4 9.83 (.387) 14.27(.562) 19.30 (0.760) 30.01 (1.19) 27.1 (1.07) 05 10.80 (.425) 15.88 (.625) 19.30 (0.760) 32.5 (1.28) 30.3 (1.19) 06 14.61 (.575) 19.05 (.750) 19.30 (0.760) 38.1 (1.50) 35.1 (1.38) 07 17.78 (.700) 23.80 (.938) 27.30 (1.073) 43.7 (1.72) 39.0 (1.54) 08 22.53 (.887) 31.75 (1.250) 33.6

17、0 (1.323) 52.4 (2.06) 46.9 (1.85) 09 30.48 (1.20) 34.93 (1.375) 33.60 (1.323) 58.7 (2.31) 57.3 (2.26) 10 33.65(1.325) 41.28 (1.625) 39.93 (1.572) 69.1 (2.72) 63.8 (2.51) 11 40.01(1.575) 47.60 (1.875) 39.93 (1.572) 75.4 (2.97) 70.0 (2.76) NOTES: 1. Dimensions are in millimeters. Inch-pound equivalent

18、s are in parentheses. 2. Dimensions apply after plating. 3. The U.S. Government preferred system of measurements is the metric SI system. However, this item was originally using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units sh

19、all take precedence. FIGURE 1. Dimensions and configuration Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93038 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 4 REQUIREMENTS: Shall be in

20、 accordance with MIL-C-85049, category 2A. Backshell shall be capable of terminating individual and/or overall shields or double overall shields and provide an environmental seal. Design and construction: See figure 1. Interface dimensions shall confirm to MIL-C-85049 accessory intermateability data

21、 for MIL-DTL-38999 series I and II connectors. Material: Accessory components: Aluminum alloy shall be in accordance with MIL-C-85049. O-ring and grommet: Shall be in accordance with MIL-C-85049. Finish: N and W shall be in accordance with MIL-C-85049. Finish N is for space application only. Part or

22、 Identifying number (PIN): The PIN shall be in accordance with the following: Example: 93038 W 11 C 05 Drawing number Finish Shell size (see figure 1) Strain relief style Cable accommodation range Marking: Marking shall be in accordance with MIL-C-85049 except the PIN shall be as stated above. QUALI

23、FICATION: Qualification inspection: Qualification inspection for the adapter specified herein shall not be required. Qualification conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-C-85049. Methods of inspection: Shall be in acc

24、ordance with MIL-C-85049. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 93038 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 A REV B PAGE 5 Approved sources of supply. Approved sources of supply are listed here

25、in. Additional sources will be added as they become available. The vendors listed herein have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. Vendor CAGE number DSCC drawing PIN 1/ 31461 06324 93038* E4130R 390EA005 1/ Parts must be purchased to this DSCC PIN t

26、o assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 31461 Electro Adapter, Incorporated 20640 Nordhoff Street Chatsworth, CA 91311 06324 Glenair, Incorporated 1211 Air Way Glendale, CA 91201-2497 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-