DLA DSCC-DWG-93042 REV C-2004 CONNECTOR ACCESSORIES ELECTRICAL BACKSHELL ENVIRONMENTAL STRAIGHT INDIVIDUAL AND OR OVERALL SHIELD TERMINATION (FOR MIL-DTL-38999 SERIES I AND II CONN.pdf

1、I NOTICE OF REVISION (NOR) r i 1. DATE (YYMMDD) 1 This revision described below has been authorized for the document listed. I 04-05-07 Form Approved OMB NO. 0704- I 0188 9. TITLE OF DOCUMENT CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, STRAIGHT, INDIVIDUAL AND/OR SERIES I AND II CON

2、HNECTORS). OVERALL SHIELD TERMINATION, (FOR MIL-DTL-38999 I Public reporting burden for this collection is estimated to average 2 hours per response, including the time for reviewing instructions, searching existing data Sources, gathering and maintaining the data needed, and completing and reviewin

3、g the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports, 1215 Je

4、fferson Davis Highway, Suite 1204, Arlington. VA 222024302, and to the Offce of Management and Budget, Paperwork Reduction Project (0704-OW), Washington, DC 20503. PLEASE DO NOT RETURN YOUR COMPLETED FORM TO EITHER OF THESE ADDRESSED. RETURN COMPLETED FORM TO THE GOVERNMENT ISSUING a. (X one) 2. PRO

5、CURING ACTIVITY NO. X (1) Existing document supplemented by the NOR may be used in manufacture. (2) Revised document must be received before manufacturer may incorporate this change. (3) Custodian of master document shall make above revision and furnish revised document. 3. DODAAC CONTRACTING OFFICE

6、R FOR THE CONTRACT/ PROCURING ACTIVITY NUMBER LISTED IN ITEM 2 OF THIS FORM. DSCC-VAI 4. ORIGINATOR n Richard L. Taylor a. TYPED NAME (First, Middle Initial, Last) Jeffery Tunstall d. TITLE CHIEF,INTERCONNECTION DEVICES 15a. ACTIVITY ACCOMPLISHING REVISION DSCC-VAI b. ADDRESS (Street, City, State, Z

7、ip Code) Defense Supply Center Columbus 3990 East Broad Street Columbus, Ohio 43216-5000 e. SIGNATURE f. DATE SIGNED (04-05-07) Richard L. Taylor b. REVISION COMPLETED (Signature) C. DATE SIGNED (04-05-07) Jeffery Tunstall 5. CAGE CODE 03723 7. CAGE CODE 03723 6. NOR NO. 5935-R039-03 . DOCUMENT NO.

8、93042 io. REVISION LETTER I b“EW c a. CURRENT B ECP NO. 11. NIA ALL 12. CONFIGURATION ITEM (OR SYSTEM) TO WHICH ECP APPLIES I 13. DESCRIPTION OF REVISION Page 3, Figure KI 07 07 1: Add “Max cable rang e“ column to accessory shell size table, as shown to the left. Provided by IHSNot for ResaleNo repr

9、oduction or networking permitted without license from IHS-,-,-LTR A 6 IREV I I I I I I I I I I I I I I I I I I DESCRIPTION DATE APPROVED Correct “A diameter 15 Dec 94 Randy Larson Update format. 16 July 02 Robert Heber Correcting references. Correcting address list of sources. PAGE REV STATUS OF PAG

10、ES REV BBBBB PAGE 12345 AMSC NIA DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. PMIC NIA Original date of drawing 14 November 1994 5935-E681 PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS Jeffery Tunstall COLUMBUS, OHIO 43216-5000 CHECKED BY TITLE Abdo Abdouni APPROVE

11、D BY Robert Heber CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, ENVIRONMENTAL, STRAIGHT, INDIVIDUAL AND /OR OVERALL SHIELD SERIES I AND II CONNECTORS) TERMINATION, CATEGORY 2A (FOR MIL-DTL-38999 DWG. NO. 93042 SIZE CAGE CODE 03723 REV B PAGE 1 OF 5 A Provided by IHSNot for ResaleNo reproduction or n

12、etworking permitted without license from IHS-,-,-, TYPE 1 O-RING, DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 KNURL MFR OP CAGE CODE DWG NO. SIZE 03723 93042 REV B PAGE 2 A PTIONAL SHIELD - TERMINATION METHOD OPTIONAL STYLE A STYLE B STYLE C FIGURE 1. Dimensions and confiauration. Provid

13、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I Accessory I A dia max I shell size o9 11 13 19.1 (0.75) 21.6 (0.85) 25.4 (1 .O01 Clamp size Cable accommodation range B max K max N max NOTES: 1. Dimensions are in millimeters. Inch-pound equivalents are in

14、 parentheses. 2. Dimensions apply after plating. 3. The U.S. Government preferred system of measurements is the metric SI system. However, this item was originally using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units shall, the inch-pound units take

15、 precedence. o1 02 03 04 05 06 07 08 o9 10 11 FIGURE 1. Dimensions and confiauration - Continued. Min Max 3.99 (.157) 5.33 (.210) 19.30 (.760) 21.4 (34) 16.0 (.63) 4.75 (.187) 7.92 (.312) 19.30 (.760) 23.0 (.91) 19.2 (.76) 7.14 (.281) 11.13 (.438) 19.30 (.760) 27.8 (1.09) 23.9 (.94) 9.83 (.387) 14.2

16、7 (562) 19.30 (.760) 30.1 (1.19) 27.1 (1.07) 10.80 (.425) 15.88 (.625) 19.30 (.760) 32.5 (1.28) 30.3 (I. 19) 14.61 (575) 19.05 (.750) 19.30 (.760) 38.1 (1.50) 35.1 (1.38) 17.78 (.700) 23.83 (.938) 27.30 (1.073) 43.7 (1.72) 39.0 (1 54) 22.53 (.887) 31.75 (1.250) 33.60 (1.323) 52.4 (2.06) 46.9 (1.85)

17、30.48 (1.200) 34.93 (1.375) 33.60 (1.323) 58.7 (2.31) 57.3 (2.26) 33.65 (1.325) 41.28 (1.625) 39.93 (1 572) 69.1 (2.72) 63.8 (2.51) 40.01 (1 575) 47.60 (1 375) 39.93 (1 572) 75.4 (2.97) 70.0 (2.76) CAGE CODE DWG NO. 03723 93042 A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IH

18、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REQUIREMENTS: Shall be in accordance with MIL-C-85049, category 2A. Backshell shall be capable of terminating individual and/or overall shields or double overall shields and provide an environmental seal. Design and

19、construction: See figure 1. Interface dimensions shall confirm to MIL-C-85049 accessory intermateability data for MIL-DTL-38999 series I and II connectors. Material: Accessory components: Aluminum alloy shall be in accordance with MIL-C-85049. O-ring and grommet: Shall be in accordance with MIL-C-85

20、049. Finish: N and W shall be in accordance with MIL-C-85049. Finish N is for space application only. Part or Identifying Number (PIN): The PIN shall be in accordance with the following: Example: - C Finish Shell size (see figure 1) Strain relief style 2 - Accessory length I 12.7 mm I 6.4 mm (0.50 i

21、nch I .25) increments: e.g., 6 = 76.2 mm (3.0 inches). 2 = 25.4 mm (1 .O inch) minimum length. Cable accommodation range Marking: Marking shall be in accordance with MIL-C-85049 except the PIN shall be as stated above. QUAL I FI CATION : Qualification inspection: Qualification inspection for the ada

22、pter specified herein shall not be required. Qualification conformance inspection: Shall be in accordance with MIL-C-85049. Inspection of packaging: Shall be in accordance with MIL-(2-85049. Methods of inspection: Shall be in accordance with MIL-C-85049. CAGE CODE DWG NO. 03723 93042 A DEFENSE SUPPL

23、Y CENTER, COLUMBUS COLUMBUS, OH 43216-5000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. The vendors listed herein

24、have agreed to this drawing and a certificate of compliance has been submitted to DSCC-VAI. I DSCCdrawinn I Vendor CAGE - PIN Il 93042* number 31461 1 06324 E4101S I 390FS005 - I/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE numb

25、er Vendor name and address 31461 06324 Electro Adapter, Incorporated 20640 Nordhoff Street Chatsworth, CA 9131 1 Glenair, Incorporated 121 1 Air Way Glendale, CA 91201-2497 CAGE CODE DWG NO. A DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 I I I REV B I PAGE 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-