DLA DSCC-DWG-94011 REV D-2005 RESISTOR CHIP FIXED FILM ZERO-OHM STYLE RM1206 [Use DLA MIL-PRF-32159 7 (1) DLA MIL-PRF-32159 7]《固定薄膜片状0欧姆RM1206型电阻器[使用 DLA MIL-PRF-32159 7]》.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Change figure 1 from a two-view drawing to a three-view drawing. Change the width and length dimensions. Editorial changes throughout. 23 NOV 94 N. Christolear B Add vendor. Editor changes throughout. 10 SEP 99 K. Cottongim C Modify PIN to include terminati

2、on material. Add new paragraphs 3.4 and 6.3. Revised figure 1 to coincide with MIL-PRF-55342/7. 12 DEC 02 K. A. COTTONGIM D Inactive for new design. New vendor plant address. Revise to present DoD policy requirements. 12 Apr 05 Kendall A. Cottongim CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOG

3、ISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH 43218-3990 Notice of Inactivation for New Design DSCC Drawing 94011 is inactive for new design and is no longer used, except for replacement purposes. Use MIL-PRF-32159/7 Prepared in accordance with ASME Y14.100 Selected item drawing REV D D

4、C D D REV STATUS OF PAGES PAGES 1 2 3 4 5 PMIC N/A PREPARED BY Andrew R. Ernst DESIGN ACTIVITY: DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 CHECKED BY Andrew R. Ernst APPROVED BY David E. Moore TITLE RESISTOR, CHIP, FIXED, FILM, ZERO-OHM, STYLE RM1206 SIZE A CODE IDENT. NO. 14933 DWG NO.

5、94011 Original date of drawing 4 March 1994 REV D PAGE 1 OF 5 AMSC N/A 5905-E486 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 94011 REV D PAGE 2 1. SCOPE 1.1 Scope.

6、This drawing describes the requirements for a zero-ohm, chip resistor with wrap around termination, style 1206. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 94011 -B | | | | Drawing number Termination material (see 3.4 however, each unit package shall be marked in accordance

7、 with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, date, and lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be

8、used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs.Inches .005 .008 .010 .020 .033 .063 .126 mm 0.13 0.20 0.25 0.51 0.84 1.60 3.20 Provided by IHSNot for ResaleNo reprod

9、uction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 94011 REV D PAGE 4 3.7 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supp

10、ly. 3.8 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MIL-STD-790 is not applicab

11、le to this document. 4.2 Qualification inspection. Qualification inspection is not applicable to this document. 4.3 Product level qualification. The product level qualification specified in MIL-PRF-55342 and MIL-STD-690 is not applicable to this document. 4.4 Conformance inspection. 4.4.1 Inspection

12、 of product for delivery. Inspection of product for delivery shall consist of group A inspection (established reliability level only and the parts per million reporting is not applicable) of MIL-PRF-55342. 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the material

13、s, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of mat

14、eriel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain requisite requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service or Defense

15、Agency, or within the Military Services System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a ge

16、neral or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended, also in most surface mount application. 6.2 Ordering data. The contract or purchase order should specify the

17、following: a. Complete PIN (see 1.2). b. Requirements for delivery and one copy of the conformance inspection data or certification of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 PIN superses

18、sion. The PIN in the original 94011 and revision B has been superseded by a new PIN in revision C that includes a code for termination material. Table I illustrates a generic PIN substitution: TABLE I. PIN supersession. Revisions through B Revision C 94011 94011-B Provided by IHSNot for ResaleNo rep

19、roduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 94011 REV D PAGE 5 6.4 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the

20、users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at Resistordla.mil or in writing to: DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. 6.5 Suggested sources of supply. Approved so

21、urces of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at Resistordla.mil or contact DSCC-VAT, 3990 East Broad Street, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC draw

22、ing PIN 94011-* Vendors similar designation or type number 1/ Vendor CAGE Vendors name and address Termination B. J1415-0R02Y 50316 Mini-Systems Incorporated Thick Film Division P.O. 69 North Attleboro, MA 02761-0069 Term. B, G, U, and C. H1206CP*000(D94011) 56235 State of the Art, Incorporated 2470

23、 Fox Hill Road State College, PA 16803-1797 Termination B. M1206XR000SB 57489 Vishay Thin Film, Incorporated 2160 Liberty Drive Niagara Falls, NY 14304-3676 Termination B. RCWPM-1206-99 91637 Vishay Dale Electronics, Incorporated PO Box 609 Columbus, NE 68602-0609 PLANT: Vishay Israel, Ltd Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-