DLA DSCC-DWG-95004 REV G-2009 FILTER EMI HYBRID.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Corrected power dissipation rating 20 Oct 1995 Andrew R. Ernst B Added case outlines T, U, Y, Z 7 July 1998 Michael A. Radecki C Added device type 02. Editorial changes. Added tab dimensions to package end on case outlines T, Y, and Z. 25 Apr 02 Kendall A.

2、Cottongim D Page 6, case outline U; corrected the L1 and T dimensions. Pages 11 and 12; Added e-mail address for contact point. 11 Feb 04 Kendall A. Cottongim E Editorial changes 18 Dec 2007 Michael A. Radecki F Editorial changes. Added pure tin prohibition paragraph. Table I: deleted requirement to

3、 measure noise reduction at 1kHz and 5MHz. 10 Dec 2008 Michael A. Radecki G Deleted device type 02. Added device type 03. 25 June 2009 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawingREV STATUS OF PAGES REV G G G G G G G G G G G G PAGES 1 2 3 4 5 6 7 8 9 10 11 12 PM

4、IC N/A PREPARED BY Patrick Kyne DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OH Original date of drawing 20 January 1995 CHECKED BY Andrew R. Ernst TITLE FILTER, EMI, HYBRID APPROVED BY Andrew R. Ernst SIZE A CODE IDENT. NO. 14933 DWG NO. 95004 REV G PAGE 1 OF 12 AMSC N/A 5915-E083 CUR

5、RENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO.

6、 95004 REV G PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for hybrid microcircuit electromagnetic interference (EMI) suppression filters to be processed in accordance with MIL-PRF-38534. Two product assurance classes consisting of class H (military high reliability) and class K

7、 (space application) and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance (RHA) levels are reflected in the PIN. 1.2 Part or Identifying Number (PIN). The complete PIN shall b

8、e as shown: 95004 - 01 H X X Drawing RHA Device Device class Case Lead number designator type designator outline finish (See 1.2.1) (See 1.2.2) (See 1.2.3) (See 1.2.4) (See 1.2.5) 1.2.1 Radiation hardness assurance (RHA) designator. Device classes H and K RHA marked devices shall meet the MIL-PRF-38

9、534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. Only the RHA levels specified herein are available. 1.2.2 Device types. The device types shall identify the circuit function as follows: Device type Generic number Circuit functio

10、n 01 FME28-461 EMI filter, 15 A 03 SFME28-461 EMI filter, 10 A (Note: Device type 02 has been deleted.) 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level as follows: Device class Device requirements documentation H or K Certi

11、fication and qualification to MIL-PRF-38534 1.2.4 Case outline. The case outline shall be as designated in MIL-STD-1835, and as follows: Outline letter Case outline Package style T See figure 1 Tabbed flange mount, lead formed up U See figure 2 Flange mount, lead formed down X See figure 3 Flange mo

12、unt, short lead Y See figure 4 Tabbed flange mount, short lead Z See figure 5 Tabbed flange mount, lead formed down 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534 for classes H and K. Finish letter “X“ will not be marked on the filter or its packaging. The “X“ designation

13、is for use when lead finishes A, B, or C are considered acceptable and interchangeable without preference. 1.3 Absolute maximum ratings. 1/ Input voltage - +50 V dc Input current - 15 A (for 01 device type); 10A (for 03 device type) Power dissipation - 19.7W (for 01 device type); 8.75W (for 03 devic

14、e type) Lead temperature (soldering, 10 seconds) - +300 C Storage temperature - -65 C to +150 C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability.Provided by IHSNot for Resal

15、eNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 3 1.4 Recommended operating conditions. Input voltage - +16 to +40 V dc Case operating temperature range - -55 C to +125 C 2. APP

16、LICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure

17、the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, st

18、andards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTM

19、ENT OF DEFENSE STANDARDS MIL-STD-883 - Test Methods Standard Microcircuits. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence

20、. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements

21、. The individual item requirements shall be in accordance with MIL-PRF-38534 and as specified herein. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-38534 and as specified herein. 3.2.1 Case outline. The case outline shall be in accordan

22、ce with 1.2.4 and on figures 1 through 5 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figures 1 through 5 herein. 3.3 Pure tin prohibition. The use of pure tin as an underplate or final finish in the internal or external construction of the filter and the ter

23、minations is prohibited. This includes the discrete devices and solders used internal to the case. The use of tin alloys other than lead is permissible as specified in APPENDIX E of MIL-PRF-38534. 3.4 Electrical performance characteristics. Unless otherwise specified herein, the electrical performan

24、ce characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.5 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.6 Mark

25、ing. Marking shall be in accordance with MIL-PRF-38534. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed on QML-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

26、ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 4 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, the manufacturer shall be certified and qualified to MIL-PRF-38534. In addition to the general requirements of MIL-

27、PRF-38534, the manufacturer of the part described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, produced on the certified line, for each device type listed herein. The data should also include a summary of all pa

28、rameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VAT) upon request. 3.8 Certificate of compliance. A certificate of compliance shall be

29、required from a manufacturer in order to supply to this drawing. The certificate of compliance submitted to DSCC-VAT shall affirm that the manufacturers product meets the requirements of MIL-PRF-38534 and the requirements herein. 3.9 Certificate of conformance. A certificate of conformance as requir

30、ed in MIL-PRF-38534 shall be provided with each lot of filters delivered to this drawing. 3.10 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or

31、exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.11 Workmanship. Filters shall be processed in such a manner as to be uniform in quality and shall be free from cold soldering, corrosion, pits, dents, cracks, rough or sharp edges, misali

32、gnments and other defects that will affect life, serviceability, or appearance. TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C Tc 125C unless otherwise specified Group A subgroup Device types Limits Units Min Max Input voltage Vin1,2,3 All 0 40 V Noise reduction NO f =

33、500 kHz 4,5,6 01 60 - dB 03 60 100 f = 1 MHz 4,5,6 01 60 - 03 60 100 DC resistance Rdc1 All - .07 Isolation ISO Any pin to case, 500 V dc 1 All 100 - M Capacitance CAP Any pin to case 1 All 50,000 70,000 pF Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

34、-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 5 Case outline T NOTES: 1. The U. S. Preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict b

35、etween the metric and inch-pound units, the inch-pound shall take precedence. 2. Device weight: 86 grams maximum. FIGURE 1. Case outline T configuration, dimensions and terminal connections.Symbol Millimeters Inches Min Max Min Max A 10.16 0.400 A1 5.33 5.84 0.210 0.230 b 0.89 1.14 0.035 0.045 D 50.

36、55 51.05 1.990 2.010 D1 37.85 38.35 1.490 1.510 e 5.08 BSC 0.200 BSC E 69.85 72.39 2.750 2.850 E1 63.25 63.75 2.490 2.510 F 1.14 1.40 0.045 0.055 L 6.10 6.60 0.240 0.260 P 3.43 3.68 0.135 0.145 q/q1 44.20 44.70 1.740 1.760 q2 28.96 29.46 1.140 1.160 s 6.10 6.60 0.240 0.260 T 10.92 11.43 0.430 0.450

37、Device type 01, 03 Case outline T(Figure 1) Terminal number Terminal symbol 1, 2, 3 +Vin10, 11, 12 +Vout* case ground 7, 8, 9 output return 4, 5, 6 input return * NOTE: Case ground connection is made by contact of the base plate to the chassis. Provided by IHSNot for ResaleNo reproduction or network

38、ing permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 6 Case outline U NOTES: 1. The U. S. Preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of m

39、easurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2. Device weight: 86 grams maximum. FIGURE 2. Case outline U configuration, dimensions and terminal connections.Symbol Millimeters Inches Min Max Min Max A 10.16 0.400 A1 5.46 5.72 0.2

40、15 0.225 b 0.89 1.14 0.035 0.045 D 37.97 38.23 1.495 1.505 e 5.08 BSC 0.200 BSC e1 3.30 BSC 0.130 BSC E 87.38 87.88 3.440 3.460 E1 75.95 76.45 2.990 3.010 E2 63.37 63.63 2.495 2.505 F 1.14 1.40 0.045 0.055 L 6.10 6.60 0.240 0.260 L1 5.59 5.84 0.220 0.230 P 3.12 3.38 0.123 0.133 q 31.88 32.13 1.255 1

41、.265 q1 69.85 70.36 2.750 2.770 S 6.22 6.48 0.245 0.255 T 5.08 7.62 0.200 0.300 Device type 01, 03 Case outline U(Figure 2) Terminal number Terminal symbol 1, 2, 3 +Vin10, 11, 12 +Vout* case ground 7, 8, 9 output return 4, 5, 6 input return * NOTE: Case ground connection is made by contact of the ba

42、se plate to the chassis. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 7 Case outline X NOTES: 1. The case was originally designed using inch-pound

43、 units of measurement; in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2. Device weight: 86 grams maximum. FIGURE 3. Case outline X configuration, dimensions and terminal connections.Device type 01, 03 Case outline X(Figure 3) Terminal number T

44、erminal symbol 1, 2, 3 +Vin10, 11, 12 +Vout* case ground 7, 8, 9 output return 4, 5, 6 input return * NOTE: Case ground connection is made by contact of the base plate to the chassis. Symbol Millimeters Inches Min Max Min Max A 10.16 0.400 A1 5.46 5.72 0.215 0.225 b 0.89 1.14 0.035 0.045 D 37.97 38.

45、23 1.495 1.505 e 5.08 BSC .200 BSC e1 3.30 BSC .130 BSC E 75.95 76.46 2.990 3.010 E1 63.37 63.63 2.495 2.505 F 1.14 1.40 0.045 0.055 L 6.10 6.60 0.240 0.260 L1 5.58 6.10 0.220 0.240 P 3.12 3.38 0.123 0.133 q 31.88 32.13 1.255 1.265 q1 69.97 70.23 2.755 2.765 s 6.22 6.48 0.245 0.255 Provided by IHSNo

46、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER, DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 95004 REV G PAGE 8 Case outline Y NOTES: 1. The U. S. Preferred system of measurement is the metric SI. This case outline was originally designed using inch- pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2. Device we