DLA DSCC-DWG-97006 REV C-2011 CAPACITORS FIXED CERAMIC DIELECTRIC NON-HERMETICALLY SEALED FEEDTHROUGH.pdf

1、 AMSC N/A 5910-2011-E12 REVISIONS LT DESCRIPTION DATE APPROVED A Editorial changes. Removed one suggested source of supply. Added a new suggested source of supply. 27 APR 01 Kendall A. Cottongim B Corrected error in Figure 1. Editorial changes throughout. 17 May 2006 Michael A. Radecki C Update for

2、5 year review. 21 June 2011 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS OF PAGES REV C C C C C C C C PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Patrick Kyne DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing: CHECKED BY Michael A.

3、Radecki TITLE CAPACITORS, FIXED, CERAMIC DIELECTRIC, 29 June 1999 APPROVED BY William E. Sindelar NON-HERMETICALLY SEALED, FEEDTHROUGH SIZE A CODE IDENT. NO. 037Z3 DWG NO. 97006 REV C PAGE 1 OF 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENS

4、E SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 2 1. SCOPE 1.1 Scope MIL-PRF-28861. This drawing and describe the requirements for feedthrough capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 97006- XXX X Drawing nu

5、mber Dash number Finish (see table I) (see 3.1.3) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or

6、as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this drawing, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standar

7、ds, and handbooks6.2. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (See ). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-288

8、61 - Filters and Capacitors, Radio Frequency/Electromagnetic Interference Suppression, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or f

9、rom the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, how

10、ever, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensionsMIL-PRF-28861. The interface and physical dimensions shall be as specified in and herein. 3.1.1 Terminals figure 1. Terminals shall be solderable and i

11、n accordance with . 3.1.2 Case dimensions figure 1. The case dimensions shall be in accordance with . 3.1.3 FinishMIL-PRF-28861. The finish shall be T (tin plated or tin-lead plated), S (silver plated), or G (gold plated) in accordance with . (NOTE: Pure tin plating is prohibited (see 6.4). Provided

12、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 3 3.2 Operating temperature range. The operating temperature range shall be -55C to +125C. 3.3 Electrical char

13、acteristics. 3.3.1 Rated voltage. The rated voltage shall be 500 V dc. 3.3.2 Rated current. The rated current shall be 10 amperes maximum. 3.3.3 Dissipation factor (DF). The DF shall be 3.0 percent maximum. 3.3.4 Capacitance table I. Capacitance shall be in accordance with . 3.3.5 Capacitance tolera

14、nce. Capacitance tolerance shall be +100 percent, -0 percent. 3.3.6 Insulation resistanceAt +25C: 1,000 megohm-microfarads or 100,000 megohms minimum, whichever is less. . When measured between one terminal and the case, insulation resistance shall be as follows: At +125C: 100 megohm-microfarads or

15、10,000 megohms minimum, whichever is less. 3.3.7 Insertion loss. Not applicable. 3.3.8 Voltage-temperature limits MIL-PRF-28861. In accordance with and the following: Capacitance change with reference to 25C Capacitance values Bias = 0 volts Bias = rated voltage 15 percent +15, -25 percent less than

16、 1000 pF 15 percent +15, -40 percent 1,000 pF and greater 3.3.9 Dc resistance. Dc resistance shall be 0.01 ohm, maximum. 3.3.10 Dc voltage drop. Dc voltage drop shall be 0.1 volt, maximum. 3.4 Thermal shock: Not applicable. 3.5 Seal. Not applicable. 3.6 Immersion. Not applicable. 3.7 Moisture Resist

17、ance. Not applicable. 3.8 Temperature rise. Temperature rise shall be +25C, maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 4 3.9 Life MIL-PR

18、F-28861. Life test shall be in accordance with . The following details and exceptions shall apply: a. Operating conditions: 200 percent of rated dc voltage shall be applied at 125C. b. Measurements after test: Capacitance: Shall change no more than 20 percent from initial measured value. Dissipation

19、 factor: Not greater than 3.0 percent. IR: at 25C, 100,000 megohms or 1,000 megohm-microfarads minimum, whichever is less. at 125C, 10,000 megohms or 100 megohm-microfarads minimum, whichever is less. 3.10 Resistance to soldering heat MIL-PRF-28861. Resistance to soldering heat test shall be in acco

20、rdance with . The following details and exceptions shall apply: a. Measurements after test: Capacitance: Shall change no more than 20 percent from initial measured value. DF: Shall not exceed 3.0 percent. IR: at 25C: Shall not be less than the initial 25C requirement. 3.11 Vibration (high frequency)

21、 MIL-PRF-28861. Vibration (high frequency) test shall be in accordance with . The following details and exceptions shall apply: a. Measurements after test: Capacitance shall meet initial requirements. 3.12 Product assurance level. Product assurance level requirements shall be class B only. 3.13 Mark

22、ing 1.2. Capacitors shall be marked with the PIN as specified in and as shown on the following example. The unit package shall be marked in accordance with MIL-STD-1285, except the PIN shall be as specified in 1.2, with the manufacturers name or Commercial and Government Entity (CAGE) code, date lot

23、 code, voltage rating, and current rating. 9 0670 -0 01 TExample of marking for the PIN on the hex flats (expanded view). 3.14 Manufacturer eligibilityMIL-PRF-28861. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the Qualified Products List (QPL) for at

24、 least one part or, perform first article inspection in accordance with the MIL-PRF-28861 qualification inspection requirements for class B. 3.15 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum e

25、xtent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.16 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of su

26、pply. 3.17 Workmanship. Capacitors shall be processed in such a manner as to be uniform in quality and shall be free from cold soldering, corrosion, pits, dents, cracks, rough sharp edges, misalignments, and other defects that will affect life, serviceability, or appearance. Cracks in glass seals ar

27、e not allowed; however, minor meniscus crazing is acceptable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 5 NOTES: 1. Dimensions are in inches. 2.

28、 Metric equivalents are given for information only. 3. Circuit diagram is for information only. 4. All capacitors shall be supplied with mounting hardware (hex nut and lockwasher). 5. Recommended mounting torque: 32 oz-inch 4 oz-inch. 6. Potting shall not extend beyond .030 inch (0.76 mm) from the b

29、ody. FIGURE 1. Case and hardware dimensions and circuit diagram. Inches mm .001 0.03 .004 0.10 .03 0.76 .047 1.19 .051 1.30 .100 2.54 .156 3.96 .250 6.35 .468 11.89 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUM

30、BUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 6 TABLE I. Electrical characteristics. PIN 97006- Capacitance (pF) 001 002 003 004 005 006 007 008 009 10 22 47 100 220 470 1000 1500 2700 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Confor

31、mance inspection. 4.2.1 Inspection of product for deliveryMIL-PRF-28861. Inspection of product for delivery shall consist of group A and group B inspections of for class B. 4.2.2 Certification6.2. The acquiring activity, at its discretion, may accept a certification of compliance with group B requir

32、ements in lieu of performing group B tests (see d). 4.2.3 Inspection of packaging MIL-PRF-28861. Inspection of packaging shall be in accordance with . 5. PACKAGING 5.1 Packaging6.2. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see ). When packa

33、ging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the Military Service

34、or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 5.1.1 Mounting hardware. Mounting hardw

35、are (hex nut and lockwasher) shall be packaged with each capacitor but need not be assembled. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 7 6. NOT

36、ES 6.1 Intended useQPL-28861. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. This drawing is intended exclusively to prevent the prolife

37、ration of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing on , this drawing becomes obsolete and will not be used for new design. The QPL-28861 product shall be the

38、 preferred item for all applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with

39、 each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of change of product to acquiring activity, if applicable

40、. 6.3 Application note. These nonhermetically sealed capacitors may be susceptible to moisture intrusion when subjected to repeated thermal cycling. If these items are to be used in applications enduring harsh environments, the user should consider placing them within hermetic enclosures. 6.4 Tin wh

41、isker growththe use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacturer. Tin whiskers may occur anytime from a day to years after manufacturer and can develop under typical operating conditions, on products that use such materials.

42、Conformal coatings applied over top of a whisker-prone surface will not prevent the formation on tin whiskers. Alloys of 3 percent by mass, have been shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposite

43、d Coatings of Tin). 6.5 Users of recordcapacitorfilterdla.mil. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Lan

44、d and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to , or by telephone (614) 692-4709 or DSN 850-4709. 6.6 Approved source(s) of supplycapacitorfilterdla.mil. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. F

45、or assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990, by email to , or by telephone (614) 692-4709 or DSN 850-4709. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE S

46、UPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 97006 REV C PAGE 8 DSCC drawing PIN 97006- Vendor similar designation or type number 1/ Vendor CAGE Vendor similar designation or type number 1/ Vendor CAGE 001- 002- 003- 004- 005- 006- 007- 008- 009- SJ1F3-100MX SJ1F3-220MX

47、SJ1F3-470MX SJ1F3-101MX SJ1F3-221MX SJ1F3-471MX SJ1F3-102MX SJ1F3-152MX SJ1F3-272MX 59942 59942 59942 59942 59942 59942 59942 59942 59942 2186-4255-100-V_F 2186-4255-220-V_F 2186-4255-470-V_F 2186-4255-101-V_F 2186-4255-221-V_F 2186-4255-471-V_F 2186-4255-102-V_F 2186-4255-152-V_F 2186-4255-272-V_F

48、66230 66230 66230 66230 66230 66230 66230 66230 66230 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name and address 59942 AVX Filters Corporation 11144 Penrose Street Sun Valley, CA 91352-3921 66230 Pacific Aerospace & Electronics, Inc Filter Division 434 Olds Station Road Wenatchee, WA 98801 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-