DLA DSCC-DWG-98023 REV A-2009 CONNECTORS ELECTRICAL RECTANGULAR NONENVIORNMENTAL MINIATURE ONE PIECE NONMAGNETIC POLARIZED SHELL GENERAL SPECIFICATION FOR.pdf

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Updated in accordance with overage review. 4/1/2009 Abdo Abdouni Prepared in accordance with ASME Y14.100 REV PAGE REV A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 PREPARED BY PMIC G Ralph Antonelli DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 C

2、HECKED BY TITLE Richard Taylor APPROVED BY Robert M. Heber CONNECTORS, ELECTRICAL, RECTANGULAR, NONENVIORNMENTAL, MINIATURE, ONE PIECE NONMAGNETIC, POLARIZED SHELL, GENERAL SPECIFICATION FOR SIZE CAGE CODE 037Z3 DWG. NO.98023 Original date of drawing 16 June 2000 A REV A PAGE 1 OF 5 AMSC N/A 5935-E7

3、98-000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 98023 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE2 1. Scope. 1.1 Scope. This drawing covers the general requirements and tests for connectors

4、designed to requirements of MIL-DTL-24308 and NASA 311P except using one piece aluminum shell and grounding detents. Connectors are available with rear grommets for wire stabilization. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as specified on the item requirements drawing and c

5、onstructed using the following format: * * * * * * * DSCC Class Style Type Contacts Mounting Shell size requirements (see 1.2.2) (see 1.2.3) (see 1.2.4) (see 1.2.5) (see 1.2.6) (see 1.2.7) drawing (see 1.2.1) 1.2.1 DSCC requirements drawing. The DSCC requirements drawing, shall state the requirement

6、 values and design modifications required of the connectors to be acquired by the Government, and shall be of the following: Requirement Drawing Contacts, size and type 99012 Size 22 Pin contacts 99013 Size 20 Pin contacts 99014 Size 22 Socket contacts 99015 Size 20 Socket contacts 1.2.2 Classes. Co

7、nnectors covered by this drawing shall be of the following classes: N - Nonmagnetic connectors. S - Same as N except class S has wire stabilizing grommet. 1.2.3 Style of termination. Connectors covered by this drawing shall be of the following signal contacts termination styles: A - Crimp removable

8、signal contacts, not included. 1.2.4 Types. Connectors covered by this drawing shall be of the following types: E - Standard density connectors for size 20 signal contacts. F - High density connectors for size 22D signal contacts. 1.2.5 Contacts. Connectors covered by this drawing shall have the fol

9、lowing contacts: P - Pin. S - Socket. 1.2.6 Mounting style. Connectors covered by this drawing shall be made with the following mounting options: R - Conventional mounting (not float mounted). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE

10、 CODE DWG NO. 037Z3 98023 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE3 1.2.7 Shell size. 1 Shell size 1 2 Shell size 2 3 Shell size 3 4 Shell size 4 5 Shell size 5 6 Shell size 6 2. Applicable documents. 2.1 General. The documents listed in this section are specified in secti

11、ons 3, 4, or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must

12、meet all specified requirements documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent sp

13、ecified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-24308 - Connectors, Electrical, Rectangular, Non-environmental, Miniature, Polarized Shell, Rack and Panel, General Specif

14、ications for. Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Documents Order Desk, 700 Robbins Avenue, Bldg. 4D (Customer Service), , Philadelphia, PA 19111-5094.) 2.3 Other Government documents, drawi

15、ngs and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract (see 6.2). National Aeronautics and Space Administration (NAS

16、A) GSFC-S-311-P-4 - Connectors, Electrical, Subminiature, Rack and Panel, General Specification for Copies of these documents are available online at http:/www.nasa.gov/centers/goddard/home/ or the National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt MD 20771. 2.4 No

17、n-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B211 - Aluminum

18、and Aluminum-Alloy, Bar, Rod, and Wire (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

19、rom IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 98023 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVA PAGE4 3. Requirements. 3.1 DSCC requirements drawing. The individual item requirements shall be in accordance with MIL-DTL-24308 and GSFC-S-311-P-4 except as specified in the requirements dr

20、awing and herein. In case of conflict between this drawing and the requirements drawing, the latter shall govern. 3.2 Design, construction and physical dimensions. The design, construction and physical dimensions shall be as specified in MIL-DTL-24308, except as specified herein and in the requireme

21、nts drawing (see 3.1). 3.2.1 Design documentation. The design documentation shall be in accordance to MIL-DTL-24308 and GSFC-S-311-P-4, and the associated requirements drawings and, unless specified in the acquisition document, shall be retained by the manufacturer, but be available for review by th

22、e contracting activity or contractor upon request. 3.2.2 Material and plating. All material and plating shall be in accordance with MIL-DTL-24308 and GSFC-S-311-P-4 unless otherwise specified. 3.2.2.1 Shell material and underplating. Shell material and underplating shall be Aluminum alloy, temper T-

23、6 shall be in accordance with ASTM B211. 3.2.2.2 Shell finish. Classes N and S connector shells shall have gold finish only. 3.3 Electrical performance characteristics. The electrical performance characteristics shall be in accordance with MIL-DTL-24308, and the requirements drawing, (see 3.1) and a

24、pply over the entire operating temperature range, unless otherwise specified. 3.4 Marking. Marking shall be manufacturers name or CAGE code, manufacturers PIN and date code. 3.5 Quality assurance requirements. Connectors furnished under this drawing shall be certified by the manufacturer to meet the

25、 requirements of MIL-DTL-24308 and the quality conformance inspection as specified herein. 3.6 Environmental and mechanical performance characteristics. The environmental and mechanical performance characteristics shall be in accordance with MIL-DTL-24308 and GSFC-S-311-P-4 and the item requirements

26、 drawing (see 3.1). 3.7 Qualifications. Qualification inspection for connectors specified herein shall not be required. 3.7.1 Quality conformance inspection. The quality conformance inspection shall be in accordance with MIL-DTL-24308 and 4.2 herein. 3.8 Manufacturer eligibility. To be eligible to s

27、upply connectors to this drawing, a manufacturer shall have submitted and had accepted a manufacturers certificate of compliance (see 3.9). 3.9 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply (see 3.1)

28、. The certificate of compliance submitted to DSCC-VAI to attain an eligible manufacturer status (see 3.8) shall state that the manufacturers product shall be in accordance with the requirements of MIL-DTL-24308 and GSFC-S-311-P-4 and the item requirements drawing (see 3.1 and 6.6). 4. Verification.

29、4.1 Qualification inspection. Qualification inspection for connectors specified herein shall not be required. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 037Z3 98023 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A

30、 REVA PAGE5 4.2 Quality conformance inspection. Quality conformance inspection shall be performed on sample units produced with equipment and procedures normally used in production. Manufacturers shall keep lot records for 3 years (minimum). Monitor for compliance to the prescribed procedures, and o

31、bserve that satisfactory manufacturing conditions and records on lots are maintained for these connectors. The records, include as a minimum, an attributes summary of all quality conformance inspections conducted on each lot, shall be available for review by customers at all times. 4.3 Group A inspe

32、ction. Group A inspection shall be in accordance with MIL-DTL-24308 and GSFC-S-311-P-4 with values specified in MIL-DTL-24308 and the item requirements drawing, as applicable. 4.3.1 Sampling plan (group A). Sampling plan for group A inspection shall be in accordance with the group A sampling plan of

33、 MIL-DTL-24308. 5. Packaging. 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-DTL-24308. 6. Notes. 6.1 Intended use. Connectors conforming to this drawing are intended for use when military specifications do not exist and qualified military connectors that

34、will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings and stock catalog listings. When a military specification exists and the product c

35、overed by this drawing has been qualified to listing on Qualified Products List, (QPL)-24308; this drawing will be inactivated and will not be used for new design. The QPL-24308 product shall be the preferred item for all applications. 6.2 Ordering data. The acquisition document should specify the f

36、ollowing: a. Complete PIN (see 1.2). b. Requirements for packaging and packing (see 5.1). c. Requirements for assembly and assembly tools (see 3.1). 6.3 Replaceability. Replaceability is determined as follows: a. Connectors covered by this drawing will replace the same generic connectors covered by

37、a contractor-prepared specification or drawing. b. When a QPL source is established, the part numbered connector specified in the requirements drawing will be replaced by the connector in the requirements drawing supersession table. 6.4 Generic test data. Generic test data may be used to satisfy the

38、 requirements of 4.3. Generic test data shall be on data codes no more than 1 year old, with the same material, design, and manufacturing process. The vendor is required to retain the generic data for a period of not less than 3 years from the date of shipment. 6.5 Comments. Comments on this drawing

39、 should be directed to DSCC-VAI, P. O. Box 3990, Columbus, Ohio 43218-3990, or telephone (614) 692-0576 or e mail rectangularconnectordla.mil . 6.6 Submission of certificate of compliance. The certificate of compliance (see 3.9) submitted to DSCC-VAI, prior to listing as an approved source of supply, shall state that the manufacturers product meets the requirements of the applicable DSCC requirements drawing and as stated herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-