DLA DSCC-VID-V62 03605 REV A-2009 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS HEX SCHMITT-TRIGGER INVERTER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - PHN 09-02-17 Charles F. Saffle Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV A A A A A A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARE

2、D BY Thanh V. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Thanh V. Nguyen APPROVED BY Thomas M. Hess TITLE MICROCIRCUIT, DIGITAL, ADVANCED HIGH SPEED CMOS, HEX SCHMITT-TRIGGER INVERTER, MONOLITHIC SILICON SIZE A CODE IDENT. NO. 16236 DWG NO. V

3、62/03605 YY-MM-DD 02-11-07 REV A PAGE 1 OF 11 AMSC N/A 5962-V038-09 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 2 1. SCOPE 1.1 Scope. This dr

4、awing documents the general requirements of a high performance hex Schmitt-trigger inverter microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establis

5、hes an administrative control number for identifying the item on the engineering documentation: V62/03605 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 74AHC14-EP Hex Schmitt-trigger inve

6、rter 1.2.2 Case outline(s). The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 14 MS-012 Plastic small-outline package Y 14 MO-153 Plastic small-outline package 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as

7、provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO S

8、IZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to 7.0 V Input voltage range (VI). -0.5 V to 7.0 V 2/ Output voltage range (VO) . -0.5 V to VCC+ 0.5 V 2/ Input clamp current (IIK) (VI 0) . -20 mA Output clamp current (IOK

9、) (VO 0 or VO VCC) . 20 mA Continuous output current (IO) (VO= 0 to VCC) 25 mA Continuous current through VCCor GND. 50 mA Storage temperature range (TSTG). -65C to 150C Package thermal impedance (JA): 3/ X package .86C/W Y package .113C/W 1.4 Recommended operating conditions. 4/ 5/ Supply voltage r

10、ange (VCC) . 2.0 V to 5.5 V Input voltage range (VI). 0.0 V to 5.5 V Output voltage range (VO) . 0.0 V to VCCMaximum high level output current (IOH): VCC= 2.0 V -50 A VCC= 3.3 V 0.3 V -4.0 mA VCC= 5.0 V 0.5 V -8.0 mA Maximum low level output current (IOL): VCC= 2.0 V 50 A VCC= 3.3 V 0.3 V 4.0 mA VCC

11、= 5.0 V 0.5 V 8.0 mA Operating free-air temperature range (TA). -55C to +125C 2. APPLICABLE DOCUMENTS JEDEC PUB 95 - Registered and Standard Outlines for Semiconductor Devices JEDEC STD 51-7 - High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Applications for copies s

12、hould be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional operatio

13、n of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output voltage ratings may be exceeded if the input and

14、output current ratings are observed. 3/ The package thermal impedance is calculated in accordance with JESD 51-7. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability f

15、or product used beyond the stated limits. 5/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT

16、 NO. 16236 DWG NO. V62/03605 REV A PAGE 4 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit cont

17、ainer. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4

18、 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline(s) shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic di

19、agram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Test circuit and timing waveforms. The test circuit and timing waveforms shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or ne

20、tworking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Limits Test Symbol Conditions VCC Temperature, TA Device type Min Max Unit 3.0 V 1.2 2.2 4.5 V

21、 1.75 3.15 Positive-going input threshold voltage VT+ 5.5 V 25C, -55C to 125C All 2.15 3.85 V 3.0 V 0.9 1.9 4.5 V 1.35 2.75 Negative-going input threshold voltage VT- 5.5 V 25C, -55C to 125C All 1.65 3.35 V 3.0 V 0.3 1.2 4.5 V 0.4 1.4 Hysteresis (VT+- VT-) VT 5.5 V 25C, -55C to 125C All 0.5 1.6 V 2.

22、0 V 1.9 3.0 V 2.9 IOH= -50 A 4.5 V 25C, -55C to 125C 4.4 25C 2.58 IOH = -4 mA 3.0 V -55C to 125C 2.48 25C 3.94 High level output voltage VOH IOH= -8 mA 4.5 V -55C to 125C All 3.80 V 2.0 V 0.1 3.0 V 0.1 IOL= 50 A 4.5 V 25C, -55C to 125C 0.1 25C 0.36 IOL = 4 mA 3.0 V -55C to 125C 0.5 25C 0.36 Low leve

23、l output voltage VOL IOL= 8 mA 4.5 V -55C to 125C All 0.5 V 25C All 0.1 Input current II VI = 5.5 V or GND 0.0 V to 5.5 V -55C to 125C 1.0 A 25C All 2.0 Quiescent supply current ICC VI= VCCor GND IO= 0 A 5.5 V -55C to 125C 20.0 A See footnote at end of table. Provided by IHSNot for ResaleNo reproduc

24、tion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Limits Test Symbol Conditions VCC Temperature, TA Device type Min Max Un

25、it Quiet output, maximum dynamic VOL VOL(P)2/ 5.0 V 25C All 0.8 typical V Quiet output, minimum dynamic VOL VOL(V)2/5.0 V 25C All -0.4 typical V Quiet output, minimum dynamic VOH VOH(V)2/5.0 V 25C All 4.6 typical V High level dynamic input voltage VIH(D)2/5.0 V 25C All 3.5 V Low level dynamic input

26、voltage VIL(D)2/CL= 50 pF 5.0 V 25C All 1.5 V Input capacitance CI VI= VCCor GND 5.0 V 25C All 10 pF Power dissipation capacitance CPD No load f = 1 MHz 5.0 V 25C All 9.0 typical pF 25C 12.8 3.0 V and 3.6 V -55C to 125C 1.0 15.0 25C 8.6 CL= 15 pF See figure 5 4.5 V and 5.5 V -55C to 125C All 1.0 10.

27、0 25C 16.3 3.0 V and 3.6 V -55C to 125C 1.0 18.5 25C 10.6 Propagation delay time, A to Y tPLH, tPHL CL= 50 pF See figure 5 4.5 V and 5.5 V -55C to 125C All 1.0 12.0 ns 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the speci

28、fied temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Characteristics are for surface-mount

29、packages only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 7 Case X Dimensions Inches Millimeters Inches Millimeters Symbol Min Max Min Max Sy

30、mbol Min Max Min Max A .069 1.75 E .150 .157 3.81 4.00 A1 .004 .010 0.10 0.25 E1 .228 .244 5.80 6.20 b .014 .020 0.35 0.51 e .050 BSC 1.27 BSC c .008 NOM 0.20 NOM L .016 .044 0.40 1.12 D .337 .344 8.55 8.75 NOTES: 1. All linear dimensions are in inches (millimeters). 2. This case outline is subject

31、to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed .006 inches. 4. Fall within JEDEC MS-012. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COL

32、UMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 8 Case Y Dimensions Inches Millimeters Inches Millimeters Symbol Min Max Min Max Symbol Min Max Min Max A .047 1.20 E .169 .177 4.30 4.50 A1 .002 .006 0.05 0.15 E1 .244 .260 6.20 6.60 b .007 .012 0.19 0.30 e .026 BSC 0.65 BSC c .00

33、6 NOM 0.15 NOM L .020 .030 0.50 0.75 D .193 .201 4.90 5.10 NOTES: 1. All linear dimensions are in millimeters (inches). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters. 4. Fall within JEDEC MO-153. F

34、IGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 9 Inputs Output A Y H L L H H = High voltage level L = Low vol

35、tage level FIGURE 2. Truth table. FIGURE 3. Logic diagram. Device type 01 Case outlines: X and Y Terminal number Terminal symbol Terminal number Terminal symbol 1 1A 8 4Y 2 1Y 9 4A 3 2A 10 5Y 4 2Y 11 5A 5 3A 12 6Y 6 3Y 13 6A 7 GND 14 VCC FIGURE 4. Terminal connections. Provided by IHSNot for ResaleN

36、o reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03605 REV A PAGE 10 NOTES: 1. CLincludes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output

37、is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 3. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO= 50 , tr 3 ns, tf 3 ns.

38、4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 162

39、36 DWG NO. V62/03605 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices,

40、classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6

41、. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes w

42、ithout notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing admin

43、istrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/03605-01XE 01295 SN74AHC14MDREP AHC14MEP V62/03605-01YE 01295 SN74AHC14MPWREP HA14MEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering

44、documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-