DLA DSCC-VID-V62 03643 REV A-2009 MICROCIRCUIT LINEAR DUAL MICROPOWER VOLTAGE COMPARATOR MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add the word, “LINEAR” to the title block. Add notes to figure 1. Make changes to 6.3. Update the boilerplate paragraphs. - ro 09-02-11 R. HEBER Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV A A A A A A A A A A A A REV ST

2、ATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY TOM HESS APPROVED BY RAYMOND MONNIN TITLE MICROCIRCUIT, LINEAR, DUAL, MICROPOWER VOLTAGE COMPARATOR, MONOLITHIC SILICO

3、N SIZE A CODE IDENT. NO. 16236 DWG NO. V62/03643 03-08-11 REV A PAGE 1 OF 12 AMSC N/A 5962-V030-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE

4、 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual, micropower voltage comparator microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identificat

5、ion. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03643 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 0

6、1 TLC3702-EP Dual, micropower voltage comparator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 8 MS-012 Plastic surface mount 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provi

7、ded by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A

8、CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VDD) -0.3 V to 18 V 2/ Differential input voltage . 18 V 3/ Input voltage range (VI) -0.3 V to VDDOutput voltage range (VO) -0.3 V to VDDInput current (II) 5 mA Output current (IO) (each output

9、) 20 mA Total supply current into VDD. 40 mA Total current out of ground . 40 mA Continuous total power dissipation (PD) . See 1.5 dissipation rating table Storage temperature range . -65C to +150C Lead temperature, 1.6 mm (1/16 inch) from case for 10 seconds +260C 1.4 Recommended operating conditio

10、ns. 4/ Supply voltage range (VDD) 4 V minimum to 16 V maximum Common mode input voltage (VIC) . 0 V minimum to VDD 1.5 V maximum High level output current (IOH) -20 mA maximum Low level output current (IOL) . 20 mA maximum Operating free air temperature range (TA) -55C to +125C 1.5 Dissipation ratin

11、g table. Ambient temperatures Case outline TA 25C Power rating Derating factor above TA= 25C TA= 70C Power rating TA= 85C Power rating TA= 125C Power rating X 725 mW 5.8 mW/C 464 mW 377 mW 145 mW 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device

12、. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ All voltage va

13、lues, except differential voltages, are with respect to network ground. 3/ Differential voltages are at the IN+ with respect to IN-. 4/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibi

14、lity or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 9

15、5 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marke

16、d with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable)

17、 above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified h

18、erein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Timing waveforms and test circuit. The ti

19、ming waveforms and test circuit shall be as shown in figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 5 TABLE I. Electrical performance c

20、haracteristics. Limits Test Symbol Conditions 1/ VDD= 5 V unless otherwise specifiedTemperature, TADevice type Min Max Unit Input offset voltage VIOVDD= 5 V to 10 V, 2/ 25C 01 5 mV VIC= VICRmin -55C to +125C 10 Input offset current IIOVIC= 2.5 V 25C 01 1 typical pA +125C 15 nA Input bias current IIB

21、VIC= 2.5 V 25C 01 5 typical pA +125C 30 nA Common mode input voltage range VICR25C 01 0 to VDD- 1 V -55C to +125C 0 to VDD 1.5 CMRR VIC= VICRmin 25C 01 84 typical dB Common mode rejection ratio +125C 83 typical -55C 82 typical kSVRVDD= 5 V to 10 V 25C 01 85 typical dB Supply voltage rejection ratio

22、+125C 85 typical -55C 82 typical VOHVID= 1 V, IOH= -4 mA 25C 01 4.5 V High level output voltage +125C 4.2 VOLVID= -1 V, IOH= -4 mA 25C 01 300 mV Low level output voltage +125C 500 Supply current IDDOutputs low, no load 25C 01 40 A (both comparators) -55C to +125C 90 See footnotes at end of table. Pr

23、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 6 TABLE I. Electrical performance characteristics continued. Limits Test Symbol Conditions 1/ VDD= 5

24、 V unless otherwise specifiedTemperature, TADevice type Min Max Unit tPLHOverdrive = 2 mV, f = 10 kHz, CL= 50 pF 25C 01 4.5 typical s Propagation delay 3/ time, low-to-high level output Overdrive = 5 mV, f = 10 kHz, CL= 50 pF 2.7 typical Overdrive = 10 mV, f = 10 kHz, CL= 50 pF 1.9 typical Overdrive

25、 = 20 mV, f = 10 kHz, CL= 50 pF 1.4 typical Overdrive = 40 mV, f = 10 kHz, CL= 50 pF 1.1 typical tPHLVI= 1.4 V step at IN+ 25C 01 1.1 typical s Propagation delay 3/ time, high-to-low level output Overdrive = 2 mV, f = 10 kHz, CL= 50 pF 4 typical Overdrive = 5 mV, f = 10 kHz, CL= 50 pF 2.3 typical Ov

26、erdrive = 10 mV, f = 10 kHz, CL= 50 pF 1.5 typical Overdrive = 20 mV, f = 10 kHz, CL= 50 pF 0.95 typical Overdrive = 40 mV, f = 10 kHz, CL= 50 pF 0.65 typical VI= 1.4 V step at IN+ 0.15 typical Fall time tfOverdrive = 50 mV, f = 10 kHz, CL= 50 pF 25C 01 50 typical ns Rise time trOverdrive = 50 mV, f

27、 = 10 kHz, CL= 50 pF 25C 01 125 typical ns 1/ All characteristics are measured with zero common-mode voltage unless otherwise noted. 2/ The offset voltage limits given are the maximum values required to drive the output up to 4.5 V or down to 0.3 V. 3/ Simultaneous switching of inputs causes degrada

28、tion in output response. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 7 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduc

29、tion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 8 Case X Dimensions Inches Millimeters Symbol Min Max Min Max A - 0.069 - 1.75 A1 0.004 0.010 0.10 0.25 b 0.014 0.020 0.35 0.51 c 0.008 no

30、minal 0.20 nominal D 0.189 0.197 4.80 5.00 e 0.050 BSC 1.27 BSC E 0.150 0.157 3.81 4.00 E1 0.228 0.244 5.80 6.20 L 0.016 0.044 0.40 1.12 n 8 leads 8 leads NOTE: 1. Controlling dimensions are inch, millimeter dimensions are given for reference only. 2. Body length does not include mold flash, protrus

31、ion, or gate burrs. Mold flash, protrusion, or gate burrs shall not exceed 0.006 inch (0.15 mm) per end. 3. Body width does not include interlead flash. Interlead flash shall not exceed 0.017 inch (0.43 mm) per side. 4. Falls within reference to JEDEC MS-012. FIGURE 1. Case outline. continued. Provi

32、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol 1 1 OUT 2 1 IN- 3 1 IN+ 4 GND 5 2 IN+ 6

33、 2 IN- 7 2 OUT 8 VDDFIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 10 FIGURE 3. Block diagram. Provided by IHSNot

34、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 11 NOTE: CLincludes probe and jig capacitance. FIGURE 4. Timing waveforms and test circuit. Provided by IHSNot for R

35、esaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03643 REV A PAGE 12 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and t

36、est requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging,

37、labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained

38、herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supp

39、ly herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Package Top side marking Vendor part number V62/03643-01XE 01295 Tape and reel 3702ME TLC3702MDR

40、EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ Package drawings, standard packaging quantities, thermal data, symbolization, and printed circuit board (PCB) design guidelines are available at CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-