DLA DSCC-VID-V62 03662 REV C-2012 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS HEX SCHMITT-TRIGGER INVERTER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 02. Update boilerplate. Editorial change throughout. - phn 06-02-22 Thomas M. Hess B Add case outline Y. Update boilerplate to current revision. - CFS 06-06-22 Thomas M. Hess C Update boilerplate paragraphs to current requirements. - PHN 12-

2、06-04 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV C C C C C C C C C C C PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARE

3、D BY Charles F. Saffle DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, HEX SCHMITT-TRIGGER INVERTER, MONOLITHIC SILICON YY-MM-DD 03-09-02 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 1

4、6236 DWG NO. V62/03662 REV C PAGE 1 OF 11 AMSC N/A 5962-V065-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing

5、 documents the general requirements of a high performance hex Schmitt-trigger inverter microcircuit, with an operating temperature range of -40C to +105C for device 01, and of -55C to +125C for device 02. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of ide

6、ntification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03662 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit fu

7、nction 01 SN74LV14AT-EP Hex Schmitt-trigger inverter 02 SN74LV14AM-EP Hex Schmitt-trigger inverter 1.2.2 Case outline. The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 14 JEDEC MO-153 Plastic small-outline Y 14 JEDEC MS-012 Plastic small-outline

8、 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute maximum ratings. 1/ Supply voltage range (VC

9、C) . -0.5 V to +7.0 V Input voltage range (VI) . -0.5 V to +7.0 V 2/ Voltage range applied to any output in the high-impedance or power-off state (VO) . -0.5 V to +7.0 V 2/ Output voltage range (VO) . -0.5 V to VCC+ 0.5 V 2/ 3/ Input clamp current (IIK) (VIVCC) 50 mA Continuous output current (IO) (

10、VO= 0 to VCC) 25 mA Continuous current through VCCor GND . 50 mA Package thermal impedance (JA) . 113C/W 4/ Storage temperature range (TSTG) . -65C to +150C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and fu

11、nctional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output voltage ratings may be exceeded

12、if the input and output current ratings are observed. 3/ This value is limited to 5.5 V maximum. 4/ The package thermal impedance is calculated in accordance with JESD 51-7.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMB

13、US COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 3 1.4 Recommended operating conditions. 5/ Supply voltage range (VCC) . 2.0 V to 5.5 V Minimum high level input voltage (VIH): VCC= 2.0 V 1.5 V VCC= 2.3 V to 2.7 V . VCCx 0.7 VCC= 3.0 V to 3.6 V . VCCx 0.7 VCC= 4.5 V to 5.5 V

14、 . VCCx 0.7 Maximum low level input voltage (VIL): VCC= 2.0 V 0.5 V VCC= 2.3 V to 2.7 V . VCCx 0.3 VCC= 3.0 V to 3.6 V . VCCx 0.3 VCC= 4.5 V to 5.5 V . VCCx 0.3 Input voltage range (VI) . 0.0 V to 5.5 V Output voltage range (VO) . 0.0 V to VCCMaximum high level output current (IOH): VCC= 2.0 V -50 A

15、 VCC= 2.3 V to 2.7 V . -2 mA VCC= 3.0 V to 3.6 V . -6 mA VCC= 4.5 V to 5.5 V . -12 mA Maximum low level output current (IOL): VCC= 2.0 V 50 A VCC= 2.3 V to 2.7 V . 2 mA VCC= 3.0 V to 3.6 V . 6 mA VCC= 4.5 V to 5.5 V . 12 mA Operating free-air temperature range (TA) Device type 01 . -40C to +105C Dev

16、ice type 02 . -55C to +125C 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor Devices JESD51-7 High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available onl

17、ine at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201.) 5/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo reproduction or networking permitted

18、without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 4 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers

19、 name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and

20、 electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and f

21、igure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuit. The timing waveforms and test

22、circuit shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test

23、Symbol Conditions -40C TA 105C 2/ -55C TA 125C 3/ unless otherwise specified VCCDevice type 01 Device type 02 Unit Limits Limits Min Max Min Max Positive-going threshold voltage VT+2.5 V 1.75 1.78 V 3.3 V 2.31 2.31 5.0 V 3.5 3.5 Negative-going threshold voltage VT-2.5 V 0.75 0.75 V 3.3 V 0.99 0.99 5

24、.0 V 1.5 1.5 Hysteresis (VT+- VT-) voltage VT2.5 V 0.25 1.0 0.25 1.0 V 3.3 V 0.33 1.32 0.33 1.32 5.0 V 0.5 2.0 0.5 2.0 High level output voltage VOHIOH= -50 A 2.0 V to 5.5 V VCC 0.1 VCC 0.1 V IOH= -2 mA 2.3 V 2.0 2.0 IOH= -6 mA 3.0 V 2.48 2.48 IOH= -12 mA 4.5 V 3.8 3.8 Low level output voltage VOHIO

25、L= 50 A 2.0 V to 5.5 V 0.1 V IOL= 2 mA 2.3 V 0.4 IOL= 6 mA 3.0 V 0.44 IOL= 12 mA 4.5 V 0.55 Input current IIVI= VCCor GND 0.0 V to 5.5 V 1.0 A Quiescent supply current ICCVI= VCCor GND IO= 0 A 5.5 V 20.0 A Input/output power-off leakage current IoffVIor VO= 0.0 V to 5.5 V 0.0 V 5.0 A Input capacitan

26、ce CIVI= VCCor GND 3.3 V 2.3 Typ 2.3 Typ pF 5.0 V 2.3 Typ 2.3 Typ Power dissipation capacitance CpdCL= 50 pF f = 10 MHz 3.3 V 8.8 Typ 8.8 Typ 5.0 V 9.6 Typ 9.6 Typ See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE

27、SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions -40C TA 105C 2/ -55C TA 125C 3/ unless otherwise specified VCCDevice type 01 Device type 02 Unit Limits Limits Min

28、Max Min Max Quiet output, maximum dynamic VOLVOL(P)4/ CL= 50 pF, TA= 25C 3.3 V 0.8 0.8 V Quiet output, minimum dynamic VOLVOL(V)4/ 3.3 V -0.8 -0.8 V Quiet output, minimum dynamic VOHVOH(V)4/ 3.3 V 3.1 TYP 3.1 TYP V High level dynamic input voltage VIH(D)4/ 3.3 V 2.31 2.31 V Low level dynamic input v

29、oltage VIL(D)4/ 3.3 V 0.99 0.99 V Propagation delay time, from input A to output Y tPLH, tPHLCL= 50 pF, TA= 25C See figure 5 3.3 V 0.3V 16.3 16.3 ns 5.0 V 0.5V 10.6 10.6 Propagation delay time, from input A to output Y tPLH, tPHLCL= 50 pF See figure 5 3.3 V 0.3V 1.0 20.4 1.0 20.4 5.0 V 0.5V 1.0 14 1

30、.0 14 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence o

31、f specific parametric testing, product performance is assured by characterization and/or design. 2/ For device type 01 only. 3/ For device type 02 only. 4/ Characteristics are for surface-mount packages only. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

32、HS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 7 Case X SEATINGPLANESEEDETAIL AbD1 7814E E1AA1e0.25(.010)c0-8LDETAIL AGAGEPLANEM0.10(.004)0.10(.004)Dimensions Symbol Millimeters Inches Symbol Millimeters Inches Min Max Min Max Min Max M

33、in Max A - 1.20 - .047 E 4.30 4.50 .169 .177 A1 0.05 0.15 .002 .006 E1 6.20 6.60 .244 .260 b 0.19 0.30 .007 .012 e 0.65 NOM .026 NOM c 0.15 NOM .006 NOM L 0.50 0.75 .020 .030 D 4.90 5.10 .193 .201 NOTES: 1. This drawing is subject to change without notice. 2. Body dimensions do not include mold flas

34、h or protrusion not to exceed 0.15 mm. 3. Falls within JEDEC MO-153. 4. All linear dimensions are shown in millimeters (inches). Inches equivalents are given for general information only. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

35、om IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 8 Case Y ebD78E E1AA1.004(0.10)SEEDETAIL A.010(0.25)c0-8LDETAIL AGAGEPLANE.010(0.25) MSEATING PLANE114PIN 1INDEX AREADimensions Symbol Inches Millimeters Symbol Inches Millimeters Min M

36、ax Min Max Min Max Min Max A - 0.069 - 1.75 E 0.150 0.157 3.80 4.00 A1 0.004 0.010 0.10 0.25 E1 0.228 0.244 5.80 6.20 b 0.012 0.020 0.31 0.51 e 0.050 NOM 1.27 NOM c 0.007 0.010 0.17 0.25 L 0.016 0.050 0.40 1.27 D 0.337 0.344 8.55 8.75 NOTES: 1. This drawing is subject to change without notice. 2. Bo

37、dy dimensions do not include mold flash or protrusion not to exceed 0.006 inches (0.15 mm). 3. Falls within JEDEC MS-012, variation AB. 4. All linear dimensions are shown in inches (millimeters). Millimeters equivalents are given for general information only. FIGURE 1. Case outlines - Continued. Pro

38、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 9 (each inverter) Input A Output Y H L L H FIGURE 2. Truth table. FIGURE 3. Logic diagram. Device typ

39、es: 01 and 02 Case outlines: X and Y Terminal number Terminal symbol Terminal number Terminal symbol 1 1A 8 4Y 2 1Y 9 4A 3 2A 10 5Y 4 2Y 11 5A 5 3A 12 6Y 6 3Y 13 6A 7 GND 14 VCCFIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

40、HS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 10 Notes: 1. CL includes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform

41、2 is for an output with internal conditions such that the output is high except when disabled by the output control. 3. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO= 50, tr 3 ns, tf 3 ns. 4. The outputs are measured one at a time with one input tran

42、sition per measurement. 5. For 3-state and Open Drain outputs tests: tPLH/tPHLS1 = Open tPLZ/tPZLS1 = VCCtPHZ/tPZHS1 = GND Open Drain S1 = VCCFIGURE 5. Timing waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY

43、CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03662 REV C PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should inc

44、lude proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial p

45、ractices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The

46、 device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a

47、 source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top-Side Marking V62/03662-01

48、XE 01295 SN74LV14ATPWREP LV14AEP V62/03662-02XE 01295 SN74LV14AMPWREP LV14AEP V62/03662-02YE 01295 SN74LV14AMDREP LV14AEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc.