DLA DSCC-VID-V62 03665 REV B-2012 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS DUAL 4-CHANNEL ANALOG MULTIPLEXER DEMULTIPLEXER MONOLITHIC SILICON.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add case outline Y. - CFS 04-03-08 Thomas M. Hess B Update boilerplate paragraphs to current requirements. - PHN 12-06-04 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared i

2、n accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing CHECKED BY Charles F. Saffle TI

3、TLE MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, DUAL 4-CHANNEL ANALOG MULTIPLEXER/ DEMULTIPLEXER, MONOLITHIC SILICON YY-MM-DD 03-10-07 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/03665 REV A PAGE 1 OF 14 AMSC N/A 5962-V067-12 .Provided by IHSNot for ResaleNo reproduction or netw

4、orking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance dual 4-channel analog multiplexer/demultiplexer microcircu

5、it, with an operating temperature range of -40C to +105C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03

6、665 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 74LV4052A-EP Dual 4-channel analog multiplexer/demultiplexer 1.2.2 Case outline. The case outline are as specified herein. Outline letter

7、 Number of pins JEDEC PUB 95 Package style X 16 JEDEC MO-153 Plastic small-outline Y 16 JEDEC MS-012 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-le

8、ad plate C Gold plate D Palladium E Gold flash palladium 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to +7.0 V Input voltage range (VI) . -0.5 V to +7.0 V 2/ Switch I/O voltage range (VIO) . -0.5 V to VCC+ 0.5 V 2/ 3/ Input clamp current (IIK) (VIVCC) . 50 mA Switch through

9、current (IT) (VIO= 0 to VCC) . 25 mA Continuous current through VCCor GND . 50 mA Package thermal impedance (JA): 4/ Case outline X . 108C/W Case outline Y . 73C/W Storage temperature range (TSTG) . -65C to +150C 1/ Stresses beyond those listed under “absolute maximum rating” may cause permanent dam

10、age to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

11、2/ The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 3/ This value is limited to 5.5 V maximum. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. Provided by IHSNot for ResaleNo reproduction or networking permitted w

12、ithout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 3 1.4 Recommended operating conditions. 5/ Supply voltage range (VCC) . 2.0 V to 5.5 V 6/ Minimum high level input voltage (VIH), control inputs: VCC= 2.0 V 1.5 V VCC=

13、2.3 V to 2.7 V . VCCx 0.7 VCC= 3.0 V to 3.6 V . VCCx 0.7 VCC= 4.5 V to 5.5 V . VCCx 0.7 Maximum low level input voltage (VIL), control inputs: VCC= 2.0 V 0.5 V VCC= 2.3 V to 2.7 V . VCCx 0.3 VCC= 3.0 V to 3.6 V . VCCx 0.3 VCC= 4.5 V to 5.5 V . VCCx 0.3 Control input voltage range (VI) . 0.0 V to 5.5

14、 V Input/output voltage range (VIO) 0.0 V to VCCMaximum input transition rise or fall rate (t/v): VCC= 2.3 V to 2.7 V . 200 ns/V VCC= 3.0 V to 3.6 V . 100 ns/V VCC= 4.5 V to 5.5 V . 20 ns/V Operating free-air temperature range (TA) -40C to +105C 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY A

15、SSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor Devices JESD51-7 High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103

16、North 10th Street, Suite 240S, Arlington, VA 22201.) 5/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. 6/ With supply voltages at or near 2 V, the analog switch on-state resistance becomes very nonlinear. It is recommended that only digital signals be tr

17、ansmitted at these low supply voltages. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 4 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently

18、and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and

19、C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions a

20、re as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal conne

21、ctions shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuits. The timing waveforms and test circuits shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE

22、A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 5 TABLE I. Electrical performance characteristics. Test Symbol Conditions VCCTemperature, TALimits Unit Min Max On-state switch resistance ronIT= 2 mA VI= VCCor GND VINH= VILSee figure 5 2.3 V 25C, -55C to 125C 225 3.0 V 25C, -55C to 125C 190 4.5 V

23、 25C, -55C to 125C 100 Peak on-state resistance ron(p)IT= 2 mA VI= VCCor GND VINH= VIL2.3 V 25C, -55C to 125C 600 3.0 V 25C, -55C to 125C 225 4.5 V 25C, -55C to 125C 125 Difference in on-state resistance between switches ronIT = 2 mA VI= VCCor GND VINH= VIL2.3 V 25C, -55C to 125C 40 3.0 V 25C, -55C

24、to 125C 30 4.5 V 25C, -55C to 125C 20 Control input current IIVI= 5.5 V or GND 0.0 V to 5.5 V 25C, -55C to 125C 1.0 A Off-state switch leakage current IS(off)VI= VCCand VO= GND, or VI= GND and VO= VCCVINH= VIHSee figure 5 5.5 V 25C, -55C to 125C 1.0 A On-state switch leakage current IS(on)VI= VCCor

25、GND VINH= VILSee figure 5 5.5 V 25C, -55C to 125C 1.0 A Quiescent supply current ICCVI= VCCor GND 5.5 V 25C, -55C to 125C 20.0 A Power dissipation capacitance CpdCL= 50 pF f = 10 MHz 3.3 V 25C 11.8 TYP pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permi

26、tted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 6 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions VCCTemperature, TALimits Unit Min Max Propagation delay time, COM or Y to Y

27、or COM tPLH, tPHLCL= 50 pF See figure 5 3.0 V and 3.6 V 25C, -55C to 125C 12.0 ns 4.5 V and 5.5 V 25C, -55C to 125C 8.0 Propagation delay time, INH to COM or Y tPZH, tPZLCL= 50 pF See figure 5 3.0 V and 3.6 V 25C, -55C to 125C 25.0 ns 4.5 V and 5.5 V 25C, -55C to 125C 18.0 Propagation delay time, IN

28、H to COM or Y tPHZ, tPLZCL= 50 pF See figure 5 3.0 V and 3.6 V 25C, -55C to 125C 25.0 ns 4.5 V and 5.5 V 25C, -55C to 125C 18.0 Frequency response (switch on), COM or Y to Y or COM CL= 50 pF RL= 600 fin= 1 MHz (sine wave) 1/ See figure 5 2.3 V 25C 30 TYP MHz 3.0 V 25C 35 TYP 4.5 V 25C 50 TYP Crossta

29、lk (between any switches), COM or Y to Y or COM CL= 50 pF RL= 600 fin= 1 MHz (sine wave) 2/ See figure 5 2.3 V 25C -45 TYP dB 3.0 V 25C -45 TYP 4.5 V 25C -45 TYP Crosstalk (control input to signal output), INH to COM or Y CL= 50 pF RL= 600 fin= 1 MHz (square wave) See figure 5 2.3 V 25C 20 TYP mV 3.

30、0 V 25C 35 TYP 4.5 V 25C 65 TYP Feed-through attenuation (switch off), COM or Y to Y or COM CL= 50 pF RL= 600 fin= 1 MHz (sine wave) 2/ See figure 5 2.3 V 25C -45 TYP dB 3.0 V 25C -45 TYP 4.5 V 25C -45 TYP Sine wave distortion, COM or Y to Y or COM CL= 50 pF RL= 10 k fin= 1 kHz (sine wave) See figur

31、e 5 VI= 2.0 Vp-p2.3 V 25C 0.1 TYP % VI= 2.5 Vp-p3.0 V 25C 0.1 TYP VI= 4.0 Vp-p4.5 V 25C 0.1 TYP 1/ Adjust finvoltage to obtain 0 dBm output. Increase finfrequency until dB meter reads 3 dB. 2/ Adjust finvoltage to obtain 0 dBm input. Provided by IHSNot for ResaleNo reproduction or networking permitt

32、ed without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 7 Case X Dimensions Symbol Millimeters Inches Symbol Millimeters Inches Min Max Min Max Min Max Min Max A - 1.20 - .047 E 4.30 4.50 .169 .177 A1 0.05 0.15 .002 .006

33、 E1 6.20 6.60 .244 .260 b 0.19 0.30 .007 .012 e 0.65 NOM .026 NOM c 0.15 NOM .006 NOM L 0.50 0.75 .020 .030 D 4.90 5.10 .193 .201 NOTES: 1. This drawing is subject to change without notice. 2. Body dimensions do not include mold flash or protrusion not to exceed 0.15 mm. 3. Falls within JEDEC MO-153

34、. 4. All linear dimensions are shown in millimeters (inches). Inches equivalents are given for general information only. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CO

35、DE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 8 Case Y Dimensions Symbol Inches Millimeters Symbol Inches Millimeters Min Max Min Max Min Max Min Max A - .069 - 1.75 E .150 .157 3.81 4.00 A1 .004 .010 0.10 0.25 E1 .228 .244 5.80 6.20 b .014 .020 0.35 0.51 e .050 NOM 1.27 NOM c .008 NOM 0.20 NOM L

36、.016 .044 0.40 1.12 D .386 .394 9.80 10.00 NOTES: 1. This drawing is subject to change without notice. 2. Body dimensions do not include mold flash or protrusion not to exceed 0.006 inches (0.15 mm). 3. Falls within JEDEC MS-012. 4. All linear dimensions are shown in inches (millimeters). Millimeter

37、s equivalents are given for general information only. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 9 Input

38、s On Channels INH B A L L L 1Y0, 2Y0 L L H 1Y1, 2Y1 L H L 1Y2, 2Y2 L H H 1Y3, 2Y3 H X X None X = Immaterial FIGURE 2. Truth table. FIGURE 3. Logic diagram. Device type 01 Case outlines X, Y Terminal number Terminal symbol Terminal number Terminal symbol 1 2Y0 9 B 2 2Y2 10 A 3 2-COM 11 1Y3 4 2Y3 12 1

39、Y0 5 2Y1 13 1-COM 6 INH 14 1Y1 7 GND 15 1Y2 8 GND 16 VCCFIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 10 FIGURE

40、5. Timing waveforms and test circuits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 11 FIGURE 5. Timing waveforms and test circuits - Continued

41、. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 12 NOTE: finis a sine wave. FIGURE 5. Timing waveforms and test circuits - Continued. Provided b

42、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 13 FIGURE 5. Timing waveforms and test circuits - Continued. Provided by IHSNot for ResaleNo reproduction or

43、 networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03665 REV B PAGE 14 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as ind

44、icated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking s

45、hall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the

46、salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be

47、construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top-Side Marking V62/03665-01XE 01295 SN74LV4052ATPWREP L4052EP V62/03665-01YE 01295 SN74LV4052ATDREP LV4052ATEP 1/ The vendor item drawing es