DLA DSCC-VID-V62 04658 REV A-2010 MICROCIRCUIT DIGITAL LOW VOLTAGE CMOS HEX SCHMITT-TRIGGER INVERTER MONOLITHIC SILICON.pdf

1、 REVISIONSLTR DESCRIPTION DATE APPROVEDA Update boilerplate paragraphs to current requirements. - PHN 10-04-19 Thomas M. Hess Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Charl

2、es F. Saffle DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.milOriginal date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, LOW VOLTAGE CMOS, HEX SCHMITT-TRIGGER INVERTER, MONOLITHIC SILICON YY-MM-DD 04-02-24 APPROVED BY Thomas M. Hess SIZE A CODE I

3、DENT. NO. 16236 DWG NO. V62/04658 REV A PAGE 1 OF 10 AMSC N/A 5962-V043-10 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 2 1. SCOPE 1.1 Scope.

4、This drawing documents the general requirements of a high performance hex Schmitt-trigger inverter microcircuit, with an operating temperature range of -40C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing e

5、stablishes an administrative control number for identifying the item on the engineering documentation: V62/04658 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74LVC14A-EP Hex Schmitt-tr

6、igger inverter 1.2.2 Case outlines. The case outlines are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 14 MS-012 Plastic small-outlineY 14 MO-153 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided

7、by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plateC Gold plateD PalladiumE Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE I

8、DENT NO. 16236 DWG NO. V62/04658 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to 6.5 V Input voltage range (VI) . -0.5 V to 6.5 V 2/ Output voltage range (VO) . -0.5 V to VCC+ 0.5 V 2/ 3/ Input clamp current (IIK) (VI 0) -50 mA Output clamp current (IOK) (VO 0) .

9、 -50 mA Continuous output current (IO) . 50 mA Continuous current through VCCor GND . 100 mA Package thermal impedance (JA): 4/ X package . 86C/W Y package . 113C/W Storage temperature range (TSTG) . -65C to 150C 5/ 1.4 Recommended operating conditions. 6/ 7/ Supply voltage range (VCC): Operating 2.

10、0 V to 3.6 V Data retention only 1.5 V minimum Input voltage range (VI) . 0.0 V to 5.5 V Output voltage range (VO) . 0.0 V to VCCMaximum high level output current (IOH): VCC= 2.7 V -12 mA VCC= 3.0 V -24 mA Maximum low level output current (IOL): VCC= 2.7 V 12 mA VCC= 3.0 V 24 mA Operating free-air t

11、emperature range (TA) -40C to +125C 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating co

12、nditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 3/ The value of VCCis provided in the recommended

13、 operating conditions table. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. 5/ Long-term high-temperature storage and/or extended use at maximum recommended operating conditions may result in a reduction of overall device life. 6/ Use of this product beyond the manufact

14、urers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits 7/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot

15、for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC PUB 95 - Registered and Standard Outlines for Semiconductor Devices JEDEC STD 51-7 -

16、High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanent

17、ly and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A a

18、nd C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimension

19、s are as specified herein. 3.5 Diagrams. 3.5.1 Case outlines. The case outlines shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal co

20、nnections shall be as shown in figure 4. 3.5.5 Test circuit and timing waveforms. The test circuit and timing waveforms shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE

21、 A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions VCCTemperature, TALimits Units Min Max Positive-going threshold voltage VT+2.7 V 25C, -40C to 125C 0.8 2 V 3.0V 0.9 2 3.6 V 1.1 2 Negative-going threshold voltage VT-2.7

22、V 0.4 1.4 V 3.0V 0.6 1.53.6 V 0.8 1.7 Hysteresis voltage (VT+- VT-) VT2.7 V 0.3 1.1V 3.0V 0.3 1.23.6 V 0.3 1.2 High level output voltage VOHIOH= -100 A 2.7 V to 3.6 V VCC 0.2 V IOH= -12 mA 2.7 V 2.2 3.0 V 2.4 IOH= -24 mA 3.0 V 2.2 Low level output voltage VOLIOL= 100 A 2.7 V to 3.6 V 0.2 V IOL= 12 m

23、A 2.7 V 0.4 IOL= 24 mA 3.0 V 0.55 Input current IIVI= 5.5 V or GND 3.6 V 5 A Quiescent supply current ICCVI= VCCor GND IO= 0 A 3.6 V 10 A Quiescent supply current delta ICCOne input at VCC 0.6 V, Other inputs at VCCor GND 2.7 V to 3.6 V 500 A Input capacitance CiVI= VCCor GND 3.3 V 25C 5 TYP pF Powe

24、r dissipation capacitance per gate Cpdf = 10 MHz 2.5 V 12 TYP 3.3 V 15 TYP Propagation delay time, A to Y tpdSee figure 5. 2.7 V 25C, -40C to 125C 7.5 ns 3.3 V 0.3 V 1 6.4 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the s

25、pecified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. Provided by IHSNot for ResaleNo repro

26、duction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 6 Case X Dimensions Symbol Inches Millimeters Symbol Inches Millimeters Min Max Min Max Min Max Min Max A - 0.069 - 1.75 E 0.150 0.157

27、3.81 4.00 A1 0.004 0.010 0.10 0.25 E1 0.228 0.244 5.80 6.20 b 0.014 0.020 0.35 0.51 e 0.050 BSC 1.27 BSC c 0.008 NOM 0.20 NOM L 0.016 0.044 0.40 1.12 D 0.337 0.344 8.55 8.75 NOTES: 1. All linear dimensions are in inches (millimeters). 2. This case outline is subject to change without notice. 3. Body

28、 dimensions do not include mold flash or protrusion, not to exceed 0.006 inches (0.15 mm). 4. Falls within JEDEC MS-012. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CO

29、DE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 7 Case Y Dimensions Symbol Millimeters Inches Symbol Millimeters Inches Min Max Min Max Min Max Min Max A - 1.20 - 0.047 E 4.30 4.50 0.169 0.177 A1 0.05 0.15 0.002 0.006 E1 6.20 6.60 0.244 0.260 b 0.19 0.30 0.007 0.012 e 0.65 BSC 0.026 BSC c 0.15 NOM 0

30、.006 NOM L 0.50 0.75 0.020 0.030 D 4.90 5.10 0.193 0.201 NOTES: 1. All linear dimensions are in millimeters (inches). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters (0.006 in). 4. Fall within JEDEC

31、MO-153. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 8 (each inverter) Input Output A Y H L L H H = High v

32、oltage level L = Low voltage level FIGURE 2. Truth table. FIGURE 3. Logic diagram. Device type 01 Case outlines: X and Y Terminal number Terminal symbol Terminal number Terminal symbol 1 1A 8 4Y 2 1Y 9 4A 3 2A 10 5Y 4 2Y 11 5A 5 3A 12 6Y 6 3Y 13 6A 7 GND 14 VCCFIGURE 4. Terminal connections. Provide

33、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 9 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses are supplied by generators having t

34、he following characteristics: PRR 10 MHz, ZO= 50 . 3. tPLHand tPHLare the same as tpd. 4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

35、e from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04658 REV A PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentati

36、on. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manuf

37、acturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the devic

38、e manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present

39、or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/04658-01XE 01295 SN74LVC14AQDREP LVC14AE V62/04658-01YE 01295 SN74LVC14AQPWREP LVC14AE 1/ The vendor item drawing e

40、stablishes an administrative control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-